Factoryfurniture PIK Manual

Factory Furniture Ltd |5 Pioneer Road |Faringdon |Oxfordshire SN7 7BU |T [phone]
[e-mail] |www.factoryfurniture.co.uk
We reserve the right to change specification without notice. © 2017 Factory Furniture Ltd
Operation & Maintenance Manual
PIK picnic table

&
5HVSRQVLEOH
)RUHVW0DQDJHPHQW
Introduction
Design
Design, shop drawings and development by Factory Furniture Ltd.
Manufacture
Factory Furniture manufactured components. Products are assembled in Factory workshops, checked and
dispatched ready for installation. Replacement products or components thereof should be ordered direct from
Factory Furniture Ltd.
Copyright
The design copyright for the product and drawing copyright remains the sole property of Factory Furniture Ltd.
General Specifications
PIK Picnic Table
Metric length 3000mm | width 1480mm | height 740mm
Imperial length 9’ 10” | width 4’ 10½” | height 2’ 5”
Approx Weight 267kg
Fixing Centres 1600mm (5’ 3”) x 750mm (2’ 5½”)
Detailed Material & Finish Specifications
Table & Seat Slats
• Manufactured from FSC®certified tanalised timber.
• Slats are profiled and left untreated as standard.
• Bolted to frame.
Frame
• Manufactured from mild steel with a hot dip galvanised finish (option available for corten steel or galv. mild
steel with a polyester powder coat (colour white as standard or as per client specification)).
• Timber slats bolted to spacer and frame and LH and RH sections of frame bolted together.
• Anchored to ground using 8 no. zinc-coated M10 x 75mm sleeve anchors per table.
General Maintenance (Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of timber table slats and frame - check all items for superficial or physical damage.
Three Monthly
Clean all items as detailed below check all fixings are seated correctly; inspect timber for serious damage and
splinters.
Six Monthly
Secure all fixings; full clean as detailed below; check that table is firmly secured to the ground
Specific Maintenance Details
FSC Tanalised Timber
Clean with a stiff brush once per year, especially in more exposed locations, in order to prevent a verdigris type
build up on the timber surface. Ideally this should be completed in early spring. During the cleaning stage, all
exposed timber surfaces should be inspected for splits and splinters. Any splinters and graffiti should be
removed and the surface sanded with 100 grit sandpaper in order to remove any uneven / sharp edges or
surfaces.
Galvanised Surfaces
For general cleaning using a damp cloth and warm soapy water only. Scourers and abrasive cleaners are NOT
suitable for this type of finish and may damage it. Before using any cleaning agents to remove graffiti etc. try
on a small, inconspicuous area first to avoid causing more unsightly damage.
2PIK PICNIC TABLE specification

Repairs
FSC Timber
For light damage, please see section on specific maintenance details above. For instances of heavy damage,
the timber item should be replaced. Please order against the part number reference in the reordering section
towards the end of this manual.
Galvanised Surfaces
For light damage to hot dipped galvanised finishes repair using a high performance cold galvanising zinc spray
(70% zinc or above). Spray application should be carried out in accordance with approved methods detailed by
the product manufacturer. Please note that it is advisable to use professional painters to achieve best results
when touching up larger areas.
Heavy Damage
In the event of serious damage to any component, replacements should be ordered from Factory Furniture Ltd.
In this event (or if the product needs to be disassembled for any reason), please contact Factory Furniture for
detailed technical advice.
Reordering / Spares
Part No. Item Description
P2009 / 01 1 no. Pik picnic table top slat set (4 slats)
P2009 / 02 1 no. Pik picnic table seat slat set (2 slats)
Instructions For Reordering
If possible, please specify job name or number at the time of reordering to enable identification of details such
as the original species of timber used, stainless steel finishes and polyester powder coat colours etc. In any
event where either, additional orders are required, or spares and replacements are required please contact
Factory Furniture Ltd. Using the part numbers given above as reference should help us to process your enquiry
more efficiently.
Note - All fittings required to assemble ordered parts will automatically be included in the order.
AutoCAD Drawing List
FF2009 / 01 PIK PICNIC TABLE GENERAL ARRANGEMENT DRAWING
FF2009 / 02 PIK PICNIC TABLE X-SECTION DRAWINGS
FF2009 / 03 PIK PICNIC TABLE TIMBER PARTS DETAIL DRAWINGS
FF2009 / 04 PIK PICNIC TABLE STEEL PARTS DETAIL DRAWINGS
FF2009 / 05 PIK PICNIC TABLE SETTING OUT DRAWING
Contacts
Factory Furniture Ltd
5 Pioneer Road
Faringdon, Oxon
SN7 7BU UK
Tel [phone]
Email [e-mail]
Web www.factoryfurniture.co.uk
3PIK PICNIC TABLE repairs

200x12mm mild steel
galvanised frame
M12x40mm
csk bolt
M12 lock nut
300 (Ctrs)
M10 x 75mm sleeve
anchor into Ø12mm
hole in foundation
Foundation -
300x300x1000mm
C20 concrete block
(recommended)
300 (Ctrs)150 (Ctrs)
80
Ø12
FFL
200x12mm mild steel
galvanised frame
1600 (Ctrs) 300 (Ctrs)
435
740
300 (Ctrs)
150
14803000
1300 Foundation - 300x300x1000mm
C20 concrete block (recommended)
Installation Instructions
ALL INSTALLATION WORKS TO BE CARRIED OUT BY COMPETENT PERSONNEL - INSTALL AS COMPLETE UNIT
Table - Surface fix
Pik Picnic Table
1. Install suitable foundation pads (see illustration) each with top face at ground level.
2. Position table in correct orientation with bases centrally on foundation pads; mark hole positions through
frame.
3. Remove the table; drill holes Ø12mm x 75mm deep (or as bolt manufacturer’s recommendations).
4. Clear debris from holes.
5. Reposition table and fix to foundation pads using 8 no. zinc-coated M10 x 75mm sleeve anchors tightened to
50Nm (or as per manufacturer’s instruction). Ensure table remains level during fixing process.
4PIK PICNIC TABLE installation