Falcon F900 SERIES Manual


F900 SERIES
User, installation and servicing instructions
BRATT PAN
G9881


Readtheseinstructionsbeforeuse






T100914 REV. 1
DATE PURCHASED:
MODEL NUMBER:
SERIAL NUMBER:
DEALER:
SERVICE PROVIDER:

2

Falcon Foodservice Equipment
HEAD OFFICE
Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.
WEEE Directive Registration No. WEE/DC0059TT/PRO
At end of appliance life, dispose of appliance and any replacement parts in a safe
manner, via a licensed waste handler. Appliances are designed to be dismantled
easily and recycling of all material is encouraged whenever practicable.
Dear Customer,
Thank you for choosing Falcon Foodservice Equipment.
This manual can be downloaded from www.falconfoodservice.com or scan
here.
IMPORTANT: Please keep this manual for future reference.

3




These instructions are only valid if the country code appears on the
appliance. If the code does not appear on the appliance, refer to the
technical instructions for adapting the appliance to the conditions for use
in that country.
Installation must meet national or local regulations. Attention must be paid
to: gas safety (installation & use) regulations, health and safety at work
act, local and national building regulations, fire precautions act.
To prevent shocks, all appliances must be earthed.
This equipment is for professional use only and must be used by qualified
persons.
The installer must instruct the responsible person(s) of the correct
operation and maintenance of the appliance.
Only competent persons are allowed to service or convert the appliance to
another gas type.
Gas appliances must have a stop cock fitted in the supply pipe work. The
user must be familiar with the location and operation of this device in order
to turn off the supply of gas in the event of an emergency.
Unless otherwise stated, parts which have been protected by the
manufacturer must not be adjusted by the installer.
Take care when moving an appliance fitted with castors.
The appliance must be serviced regularly by a qualified person. Service
intervals should be agreed with the service provider.

4

CONTENTS
Section1:Generalremindersandnotes
1.1.Generalreminders6
1.2.Technicaldata7‐8
1.3.Construction8
1.4.Installationconformity8‐9
1.5.Specialrequirementsfortheinstallationsite9
Section2:Positioning,installationandmaintenance
2.1.Positioning9
2.2.Installation10
2.2.1.Connectiontowatersupply10
2.2.2.Gasconnectionprocedures10
2.3.Checkinggassystemoperation10‐11
2.3.1.Controlofgasinletpressure11
2.3.2.Controlofprimaryairflow11
2.3.3.Controlofpilotburner12
2.3.4Operationcontrol12
2.4.Commissioningandtesting12
2.5.Conversiontoothergastypes12‐13
2.5.1.Replacementofinjectorsformainburners13
2.5.2.Replacementofinjectorsforpilotburner13
2.6.Maintenanceofappliance13
2.6.1.Troubleshooting13‐14
Section3:Useandcleaning
3.1.Warningsandhintsforuser14
3.2.Instructionsforuse15
3.2.1.Basicoperation15
3.3.Cleaningandcareoftheappliance15‐16
3.3.1.Dailycleaning16
3.4.Specialproceduresincaseoflonginactivity16
3.5.Specialproceduresincaseoffailures16
Section4:Figuresanddetails
4.1.Unitdimensionsandconnectionpositions17
4.2.Measuringinletpressure18
4.3.Gascockdetail19
4.4.Pilotburner20
4.5.Mainburner20

5

4.6.Primaryairregulation21
4.7.Knobforwaterinlet21
4.8.Controls21
APPLIANCE INFORMATION
This appliance has been CE-marked on the basis of compliance with the relevant EU
directives for the heat inputs, gas pressures and voltages stated on the data plate.
1.1. GENERAL REMINDERS
Read the warnings contained in this manual carefully as they provide important information
concerning safety during installation, use and maintenance.
Keep these instructions for future use! Only trained personnel should use the equipment.
The appliance should be used only for the purpose for which it has been specifically
designed; other uses are improper and hence dangerous.
During operation, surfaces can become hot.
Unplug appliance in the event of failure or improper operation.
Provision should be made for regular servicing in order to maintain performance of the
equipment.
All important information about the appliance required for technical service is located on the
technical data plate. Refer to Section 3.6.
In the event of technical assistance being required, the problem must be described in as
much detail as possible so that a service technician can assess the nature of any such
event.
PPE should be worn during installation and maintenance operations.

6

Warning! : Follow the fire prevention regulations very carefully.
WARNING! : THE UNIT SHOULD NOT BE USED AS A FRYER!
1.2 TECHNICAL DATA
Gaspart
ModelOuter
dimensions
cm
Qn
kW
Gas
connection
G20
Hi=9,45
kWh/m³
m³/h
G30
Hi=12,68
kWh/kg
kg/h
80litre80X90X9022R½”2.31.73
Cooking Pan Characteristics
Model Dimensions (mm) Pan capacity Angle of Drain minimum
(Max. Level) pan rotation width (mm)
720 x 560 x 225 80 litres 80° 125

7

Table 4 – Technical data (injector table)
Cat.:II2H3+TYPEOFCONSTRUCTION“A”
Model80lt
Ratedpower(kW)22
Minimumpower(kW)“ON/OFF”
Gasconsumption
G20(Hi=9,45kWh/m3)inm3/h
G30(Hi=12,68kWh/kg)inkg/h

2,3
1,73

Injector
Ø
In
1/100
mm

Pilot
G2020mbar:Ratedpower
Minimumpower
40
4x270
“ON/OFF”
25
4x120
“ON/OFF”
Pilot
G3028‐30/37mbar:
Ratedpower
Mini.power
Primarydistance“H”G20

G30
20
30
Table 7a
Nominal main pressurefor the Gas family 2 – Natural 20 mbar
different typesof gas Gas family 3 – Propane 28-30/37 mbar
Table 7b
Operation permissible Gas family 2 – Natural from 17 mbar
if pressureis inthe range: Gas family 3 – Propane from 20/25 to 35/45 mbar
Table 7c
Operation non permissible Gas family 2 – Natural from 17 to 25 mbar
ifpressureislowerthan: Gas family 3 – Propane from 20/25 mbar
Table 7d
Operation non permissible Gas family 2 – Natural 25 mbar
if pressureis higher than: Gas family 3 – Propane from 35/45 mbar

8

1.3 CONSTRUCTION
Robust stainless steel structure mounted upon adjustable legs.
Exterior panels are stainless steel 18/10.
Stainless steel pan, pan base is 304 grade.
Stainless steel pan lid (AISI 304).
Hand-tilting of pan.
Pan is heated by four stainless steel burners.
Gas is supplied via control as detailed in Section 4.3
Main burner is lit by means of a pilot with fixed injector.
Thermostat temperature adjustment is from 100°C to 290°C.
Stainless steel flue.
The following components are included as standard:
Safety thermostat, piezo ignition, burner, pilot, plug, thermocouple and control knob. 
1.4. INSTALLATION CONFORMITY
When installing the unit, it is necessary to follow and comply with the following regulations:
Current regulations at time of installation.
Municipal and/or territorial building regulations and fire prevention prescriptions;
Current accident prevention guidelines;
Standards for the use of combustible gas;
Standards for gas-fired systems utilizing natural or propane gas;
Standards relating to gas-fired cooking appliances and equipment for large-scale catering.
Safety requirements; Standards relating to gas systems for appliances used in professional
kitchens and communal facilities;
The regulations of the gas supply company or agency;
Electricity board regulations concerning safety;
The regulations of the electrical power supply company or agency and any other local
legislation with regard to equipment operation.
1.5. SPECIAL REQUIREMENTS FOR THE INSTALLATION SITE
The appliance belongs to the installation class A1 (no direct connection of a chimney or flue
exhaust system is required). It is very important for the environment in which it is installed to
be well-aired.
In addition, it is good policy to position the unit below an extractor hood so that cooking
vapours can be removed rapidly and continuously.
The gas supply system must be equipped with an isolation control that can be shut down in
the event of servicing or an emergency.
This unit requires two water connections: one for hot and one for cold water. Each line must
be fitted with an on-off valve.

9

Warning! The shut-off valves must both be located close to the appliance, within easy reach
for the user.
SECTION 2 – POSITIONING, INSTALLLATION and MAINTENANCE
2.1. POSITIONING
Remove all packaging and check that appliance is in perfect condition. If visible damage is
detected, do not connect the appliance and notify the service agent immediately.
Remove all PVC protection from the exterior panels.
Dispose of packaging according to regulations.
Maintain a distance of 300mm between the rear (flue) of unit and the wall. There are no
particular dimensions regarding side distances from other equipment or walls, however it is
advisable to leave enough space in case of maintenance and/or repairs. It is advisable to fit
suitable heat insulation if unit is in direct contact with walls made of combustible material.
The appliance must stand level. Small differences in level can be eliminated by screwing or
unscrewing the adjustable feet: A significantly uneven or sloping stance can affect the
operation of the appliance adversely.
2.2. INSTALLATION
Warning! Only qualified technicians install, maintain and test this appliance.
Warning! Before connecting any part of the unit to main supplies, make sure that the latter
is equivalent the requirements stated in the technical data plate, if the appliance has been
designed for these supplies.
2.2.1. CONNECTION TO WATER SUPPLY
Water inlet pressure must be between 50 and 300kPA, otherwise a pressure regulator must
be installed before the appliance.
A water tap is connected to the appliance.
The water connection must be in conformity with regulation at time of installation.
2.2.2. CONNECTION TO GAS SUPPLY
The choice of the gas piping depends on the diameter required for the type of gas, appliance
and installation and should be performed in conformity with current regulations.
The gas supply can either be fixed or quick-release; if flexible pipes are employed they must
be made from stainless material and not be affected by corrosion.
The gas inlet is located at the rear on the lower right side of the appliance.
When the unit has been connected, carry out a leak test on all the fittings connecting the
appliance to the main supply. It is advisable to use a leakage spray, otherwise treat parts
with foam that does not cause corrosion; no bubbles should develop. Also, carry out a leak
test on the rapid cut-off valve.
Warning! Flames are strictly prohibited for leakage tests!

10

2.3 CHECKING THE OPERATION OF THE GAS SYSTEM
Check that the appliance has been prepared (category and type of gas) equivalent to the
family of gas available on site. If not, it is necessary to convert the appliance to whatever is
available. Refer to Section 2.5.
The appliance must be used with the correct injectors for its thermal power rating
(See Table 4 in Section 1.2).
The operation of the appliance with its heating capacity depends on the inlet pressure and
the calorific power of the gas.
The pressure range (inlet pressure) within which the appliance is allowed to operated is
stated of the paragraph “Technical Data”. The appliance shall not be operated out of the
given pressure range. If pressure should differ from the figures stated in Table 6b, advise
gas supplier or the company which has installed the system.
Power rating with G30
The power rating is achieved by using the injectors indicated in the table without any
preliminary regulation.
The possibility of operation depends on the supply pressure available:
Admitted if inlet pressure is within the range 20-35 and 25-45 mbar.
Non-admitted if the pressure is lower than 20-25 mbar or higher than 35-45 mbar.
Inform installer and do not start operation before the cause has been found and eliminated.
Power rating with G20
The power rating is achieved by using the injectors indicated in the table without any
preliminary regulation.
The possibility of operation depends on the supply pressure available:
Admitted if supply pressure is within the range 17 and 25 mbar
Non-admitted if the pressure is lower than 17 mbar or higher than 25 mbar. Inform installer
and do not start operation before the cause has been found and eliminated.
The power rating for the maximum position is obtained in all the burners when the right
injectors have been installed. Compare the injectors installed with those indicated in Table 4.
There is no the minimum power because the main burners work in ON/OFF.
Request the heat value to the gas supply board and control the injectors according to the
data indicated in Table 4.

11

2.3.1 CONTROL OF THE GAS INLET PRESSURE
The feed pressure is measured using a liquid pressure gauge (eg: a U-shaped pressure
gauge, minimum definition 0.1 mbar). The supply pressure can be measured directly at the
inlet pressure intake on the gas feed pipe. The inlet pressure intake can be reached by
opening the lower front panel once the two side screws have been removed. Refer to
Section 4.2.
Undo or remove pressure intake screw
Connect U-shaped pressure gauge
Start the appliance according to instructions
Measure inlet pressure
Disconnect U-shaped pressure gauge and tighten sealing screw
Warning! The sealed adjuster screws on the gas solenoid valve must not be tampered with,
otherwise any guarantee rights shall be forfeited immediately.
2.3.2 CONTROL OF PRIMARY AIR FLOW
Primary air can be considered correctly adjusted if no flame lift is ensured when the burner is
cold and the injector lights when the burner is hot.
The distance recommended for primary air regulation is indicated in Table 4.
2.3.3 CONTROL OF PILOT BURNER
Start the pilot burner according to instructions. If the pilot is adjusted correctly, the ignition
flame will contact the thermocouple evenly and the flame will have a perfect appearance.
Otherwise it is necessary to check if the correct injectors have been installed (see table 4).
2.3.4 OPERATION CONTROL
Start the appliance according to instructions for use.
Control that the appliance does not leak.
Control combustion safety in the regulation range by passing from maximum to minimum
Control that the regulation of the pilot flame is correct (use of correct injectors).
Control progressive ignition and correct regulation of main burner flames.
2.4 COMMISSIONING AND TESTING
Once all the connections have been made, the appliance and the overall installation must be
checked following the directions given in this manual.
Check in particular:
That the protective film has been removed from the external surfaces;
That connections have been made in accordance with the requirements and directions
indicated in this manual;
That all safety requirements in current standards, statutory regulations and directives have
been met;

12

That the water and gas connections are leak-free;
That the electrical connection has been performed according to standards.
Now the burner can be lit by following instructions for use and these points:
Progressive ignition of the burner;
even flame;
flame security: check these points at both minimum and maximum output.
Check flue gas exhaust is not clogged and that they are expelled without any hindrance.
The test report must be completed in full and submitted to the customer who should then
sign in acceptance. With effect from this moment, the appliance is covered by the
manufacturer’s warranty.
2.5. CONVERSION TO OTHER TYPES OF GAS
To adapt appliance to another gas type, for instance from G20 to G30, it is necessary to
control if main burner injectors and by-pass screws have been installed properly; in addition,
it is also necessary to replace the oven pilot burner injector (see Table 5 “Technical Data”).
All injectors needed for different types of gas are supplied with unit.
2.5.1. REPLACEMENT OF INJECTORS FOR MAIN BURNERS
To access injectors, remove water inlet tap knob, control panel and pan-tilting hand wheel.
2.5.2. REPLACEMENT OF INJECTORS FOR PILOT BURNER
Undo screw (E) and replace injector (D) with appropriate injector (see Table 3).
With a size 12 key, undo injector and replace it with injector to suit gas supply (see Table 3).
Control the correct distance “H” for primary air (refer to Section 4.6).
ATTENTION! After each conversion, the unit must be tested to ensure that there are no
leakages and that it operates correctly.
2.6. MAINTENANCE OF THE APPLIANCE
Warning!: All maintenance operations shall only be performed by a technically qualified
service centre!
To ensure correct and safe operation, the appliance must be inspected and serviced at least
once a year only. Maintenance includes components, pipes, feeding pipes etc.
It is advisable to replace worn components during maintenance operations to avoid the need
for other maintenance calls and unexpected failures.
It is also advisable to apply for a maintenance contract with the customer.

13

2.6.1. TROUBLESHOOTING
Warning! Only qualified service centre should perform the operations described
below!
Warning! Before resetting safety thermostat, it is always necessary to eliminate the
problem causing its activation!
Problem and possible cause
Access to components and operation
THE MAIN BURNER DOES NOT LIGHT UP!
The ignition plug is not fixed correctly or the connection is faulty.
The piezo igniter has been damaged.
There is a loss of gas supply pressure.
The injector is clogged or the gas cock is damaged.
The pilot burner turns off when control knob or igniter button is released
The thermocouple is not heated sufficiently by the pilot burner.
The gas cock is faulty
The pilot burner is on but the main burner does not light
Loss of pressure in the gas supply
The injector is clogged or the gas cock is damaged
The gas outlet holes are clogged
The heating pan temperature cannot be adjusted
The bulb is faulty.
The thermostat is faulty. Even normal use may cause operation inconveniences and failures.
The most common problems are the following.
Ignition plug and thermocouple
Remove the lower front panel.
Remove the igniter cable and loosen the screws of pilot burner support
Replace the plug and install the new plug working in the opposite order.
Remove the thermocouple by loosening the screws of pilot burner support
Replace the thermocouple and install the new thermocouple working in the opposite order.
Unscrew gas pipe and undo thermocouple connections, remove bulb from its seat.
Undo both screws that fix the gas valve with a suitable spanner.
Install a new control and replace parts in reverse order.

14

SECTION 3 – USE and CLEANING
3.1. WARNINGS AND HINTS FOR USER
This manual contains all instructions required for proper and safe use of the unit.
Keep the manual in a safe place for future consultation!
This appliance is for catering use and must only be used by trained kitchen staff.
The appliance must always be observed during use.
Warning! The manufacturer shall not be held responsible for injuries or damage due to
non-compliance with safety rules or improper use of the appliance by the operator.
Some operating conditions may be caused by an improper use of the appliance, it is
important to train personnel properly.
All the installation and maintenance operations must be performed by fitters who are
members of an official register.
Regular maintenance is required and customers are recommended to sign a service
agreement.
In case of failures concerning the appliance, all outputs (gas and water) must be cut off
instantly.
In case of recurrent failures contact a service technician.
3.2. INSTRUCTIONS FOR USE
Before using the appliance for the first time, thoroughly wash the interior of the pan.
Warning! Fill pan up to a maximum depth of 40mm below overflow, according to the
maximum level mark, including the food to be cooked.
3.2.1. BASIC OPERATION
The appliance is equipped with a selector to start all cooking operations (see figure
“Controls”).
Here is a list of the procedures for a safe and correct use of the appliance.
The appliance can be started only once it has been filled.
PILOT BURNER LIGHTING
Starting from position press thermostat knob and turn leftwards to position; keep the
thermostat knob pressed and press the ignition button several times .
Keep thermostat knob pressed for a few more seconds.
Release thermostat knob and control if the pilot burner is lit.
Repeat operation if the flame turns off.

15

MAIN BURNER IGNITION AND TEMPERATURE REGULATION
Once the pilot burner has been lit, turn the thermostat knob towards left to the desired
temperature. The thermostat knob is numbered from 1 to 7; the temperatures corresponding
to each position are the following:
Position 1 2 3 4 5 6 7
°C 100 125 150 180 210 250 290
The regulation of the thermostat causes automatic ignition and turning off of the main burner
(ON/OFF regulation); only the pilot flame is lit. When the thermostat knob is turned to
position , the main burner is constantly off and only the pilot flame is on.
TURNING THE PILOT BURNER OFF
Press thermostat knob and turn to position to turn off pilot burner and prevent main
burner from lighting.
3.3. CLEANING AND CARE OF THE APPLIANCE
Correct operation is only guaranteed if these instructions are followed very carefully.
Any repair or maintenance operation must be performed by a qualified technician.
We recommend that the appliance should be serviced at least annually. For this purpose,
it is advisable to arrange a service contract with Serviceline.
Keep thermocouples clean and handle such parts carefully.
Inspect burner holes periodically; these must always be kept free of obstruction.
Never use an aggressive substance or abrasive detergent when cleaning stainless steel
parts.
Avoid using steel pads as these may cause rust. For the same reason, avoid contact with
materials containing iron.
Do not use sandpaper or abrasive paper for cleaning; in special cases use a powder pumice
stone. In instances of particularly resistant staining, it is advisable to use an abrasive sponge
type. (e.g. Scotch-Brite).
It is advisable to allow the pan to cool before any cleaning or maintenance commences.
3.3.1. DAILY CLEANING
Warning! When cleaning the appliance never use a direct jet of water. Infiltration could
cause damage to components and affect warranty.
Clean pan with water and a detergent, rinse thoroughly and dry well with a soft cloth.
External surfaces should be washed down using a sponge soaked in hot water with a
suitable proprietary cleaner added.
Always rinse all surfaces with clean water and dry thoroughly with a soft cloth.

16

3.4. SPECIAL PROCEDURES IN CASE OF PROLONGED INACTIVITY
If the unit is to stand idle for any length of time (e.g. holidays or seasonal closing) it must be
cleaned thoroughly, leaving no trace of food or dirt.
Leave lid open so that air can circulate inside pan.
For added care after cleaning, external surfaces may be protected by applying a proprietary
metal polish.
Be absolutely certain to shut off all utilities (gas and water).
Air the room appropriately.
3.5. SPECIAL PROCEDURES IN CASE OF FAILURES
If the appliance should not work properly during use, turn it off immediately and shut down all
supplies (gas and water).
Apply to a service centre for help.
The manufacturer shall not be held responsible nor has any warranty commitments for
damage caused by non-compliance with prescriptions or by installation not in conformity with
instructions.
The same applies in case of improper use or different application by the operator.







17

SECTION 4 – FIGURES and DETAILS
4.1 UNIT DIMENSIONS AND CONNECTION POSITIONS
A. Water connection d.12
G. Gas connection R ½” in conformity with ISO 7-1

18

4.2 MEASURING THE INLET PRESSURE
A. Screw
B. Pressure intake
C. Gas tube
AC
B

19

4.3 GAS COCK DETAIL
A. Bulb F. Minimum output adjustment screw
B. Pilot output adjustment screw G. Maximum output adjustment screw
C. Gas outlet for pilot H. Gas outlet
D. Pressure plug at inlet I. Gas inlet
E. Pressure plug at outlet L. Control knob
IMPORTANT! The visible adjustment screws on the controls must not be recalibrated.
These parts have been set and sealed in the factory.

20

4.4 PILOT BURNER
A. Thermocouple D. Injector
B. Pilot burner E. Tightness screw
C. Ignition plug



4.5 MAIN BURNER
A. Burner B. Injector C. Injector pipe
B
C
A