Falcon F900 SERIES Manual

1
F900 SERIES
User, installation and servicing instructions
NEUTRAL UNIT
N940, N940D, N940DR, N940T, N941, N960, N960D,
N960DR, N961, N910, N920
Read these instructions before use
T100893
DATE PURCHASED:
MODEL NUMBER:
SERIAL NUMBER:
DEALER:
SERVICE PROVIDER:
REV. 6
Published: 12/10/2016

2
Falcon Foodservice Equipment
HEAD OFFICE
Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.
WEEE Directive Registration No. WEEE/DC0059TT/PRO
At end of appliance life, dispose of appliance and any replacement parts in a safe
manner, via a licensed waste handler. Appliances are designed to be dismantled
easily and recycling of all material is encouraged whenever practicable.
Dear Customer,
Thank you for choosing Falcon Foodservice Equipment.
This manual can be downloaded from www.falconfoodservice.com or scan
here.
IMPORTANT: Please keep this manual for future reference.

3
SYMBOLS
• SPANNER • SCREWDRIVER • COOKING OIL • GREASE
• SPARK IGNITION • FLAME • WARNING • VIEWPORT
• ALLEN KEY •IGNITER

4
These instructions are only valid if the country code appears on the
appliance. If the code does not appear on the appliance, refer to the
technical instructions for adapting the appliance to the conditions for use
in that country.
Installation must meet national or local regulations. Attention must be paid
to: safety (installation & use) regulations, health and safety at work act,
local and national building regulations, fire precautions act.
To prevent shocks, all appliances must be earthed.
This appliance has been CE-marked on the basis of compliance with the
Low Voltage and EMC Directives for the voltages stated on the data plate
This equipment is for professional use only and must be used by qualified
persons.
The installer must instruct the responsible person(s) of the correct
operation and maintenance of the appliance.
Only competent persons are allowed to service this appliance.
Unless otherwise stated, parts which have been protected by the
manufacturer must not be adjusted by the installer.
Take care when moving an appliance fitted with castors.
The appliance must be serviced regularly by a qualified person. Service
intervals should be agreed with the service provider.
Check that no damage has occurred to the appliance, power cable, or plug
during transit. If damage has occurred, do not use this appliance.
Installation, periodic testing, repair and fixed wiring connections should
only be undertaken by a competent electrician.
Ensure power cable is routed free from the appliance to avoid damage.
We recommend supplementary electrical protection with the use of a
residual current device (RCD)
The appliance has been designed and approved to use Falcon Kick plates,
non Falcon kick plates could potentially adversely affect the performance
of the appliance by restricting the air to the appliance.

5
CONTENTS
1APPLIANCE INFORMATION.........................................................................................6
2SPECIFICATION ...........................................................................................................7
3DIMENSIONS / CONNECTION LOCATIONS................................................................8
4INSTALLATION ...........................................................................................................11
4.1 ASSEMBLY ..........................................................................................................11
4.2 EQUIPOTENTIAL CONNECTION ........................................................................11
4.3 SUITING...............................................................................................................11
5SPARE PARTS............................................................................................................14
6SERVICING INFORMATION .......................................................................................14

6
1 APPLIANCE INFORMATION
This appliance has been CE-marked on the basis of compliance with the relevant EU
directives for the heat inputs, gas pressures and voltages stated on the data plate.
A - Serial No
B - Model No
C - Flue Type
D - Gas Category
E - Gas Pressure
F - Gas Type
G - Gas Rate
H - Total Heat Input
I - Electrical Rating
J - Total Electrical Power
K - Magnetic Field Frequency
L - Electrical Phase Loading

7
2 SPECIFICATION
Model
Description
N940
400mm unit
N940D
400mm unit with left hand door
N940DR
400mm unit with right hand door
N940T
400mm worktop unit
N941
400mm unit with side guides
N960
600mm unit
N960D
600mm unit with left hand door
N960DR
600mm unit with right hand door
N961
600mm unit with side guides
N910
100mm Infill unit
N920
200mm Infill unit

8
3 DIMENSIONS / CONNECTION LOCATIONS

9

10

11
4 INSTALLATION
4.1 ASSEMBLY
4.1.1 Position appliance and level using feet or castor adjusters as shown below.
4.2 EQUIPOTENTIAL CONNECTION
4.2.1 This appliance is also provided with a terminal for connection of an external
equipotential conductor. This terminal is in effective electrical contact with all
fixed exposed metal parts of the appliance, and shall allow the connection of
conductor having a nominal cross-section area of up to 10mm². It is located at
the rear of the unit and identified by the following label and must only be used
for bonding purposes.
4.3 SUITING

12
“Patent pending, application no. GB 1511389.7”
4.3.1 Before leveling and suiting units ensure the units are fully built, including all
accessories and castings.
4.3.2 Undo the 4 fixing screws on the control panel and remove.
4.3.3 Remove the hob rear infill and replace with rear suiting plate and fixings.
4.3.4 Remove the front side panel countersunk screw and suiting plate.
NOTE:The DLS system is designed to give a quick and easy suiting solution. If you
require an improved seal between appliances we recommend you use, a food grade,
high temperature silicon sealant. This can be supplied by Falcon part no –523400021
4.3.5 Run a bead of silicon 5 mm from profile edge as highlighted below.
4.3.6 Slide suited units into position.

13
4.3.7 Right hand unit: Screw the M5 x 40 screw (supplied in the kit) into one of the
suiting plates as shown and then insert through the front fixing holes of both
units.
4.3.8 (B) Left hand unit: Slide the penny and lock washer on to the screw and
secure using the M5 nut.
4.3.9 (C) Remove the front bolts from feet, insert base tie plate and secure the bolts
back into position.
4.3.10 (D) Replace fixings on the rear hob and tighten screw caps into position.
4.3.11 Replace control panel.
A
B
C
D

14
5 SPARE PARTS
F900 SCREW CAP KIT
533550009
NEUTRAL UNIT LH HINGE KIT
533810001
400 LH DOOR ASSY
533810000
MAGNET CATCH ASSY
533810003
ADJUSTABLE LEG 150MM
535480067
SWIVEL CASTOR SET OF 2
535400222
FIXED CASTOR SET OF 2
530964340
ST/ST ADJUSTABLE FEET
535150025
NEUTRAL UNIT RH HINGE KIT
533810004
400 RH DOOR ASSY
533810005
600 LH DOOR ASSY
533910000
600 RH DOOR ASSY
533910001
When ordering spares, quote the following:
Model Number
Serial number
This information will be found on data plate attached to the appliance. (see 1.0)
Visit our website for further spares information.
6 SERVICING INFORMATION
It is recommended to have a maintenance contract with a local service provider.
SERVICELINE CONTACT:
(UK only)
Phone: [phone]
Warranty Policy Shortlist
For our warranty policy please go to www.falconfoodservice.com