Fantini Cosmi CH119NFC User manual

CH119NFC
NFC WEEKLY
PROGRAMMABLE THERMOSTAT
INSTRUCTIONS FOR USE
FANTINI COSMI S.p.A.
Via dell’Osio, 6 20090 Caleppio di Settala, Milan – ITALY
Tel. [phone] | Fax [phone] | [e-mail]
www.fantinicosmi.it

2
NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
Thank you for purchasing a FANTINI COSMI S.p.A. product.
Please read this instruction manual carefully and always keep it at hand should you need to consult it for any reason.
The documentation reflects the characteristics of the product. However, for regulatory or commercial developments,
customers should verify the availability of updates relating to this documentation on the FANTINI COSMI S.p.A.
website: pdf.fantinicosmi.it
OPERATION
The CH119NFC is a two-temperature + antifreeze temperature weekly programmable thermostat that allows you to
adjust the room temperature in both heating and cooling.
CONTENTS OF PACKAGE
■1 programmable thermostat
■2 6/32UNC American standard thread screws to secure onto 503 recessed box (approximately Ø 3.5mm)
■1 quick guide

3
NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
DESCRIPTION OF DISPLAY KEYS
1 Date and time setting
2 Operating mode: AUTO - MAN - OFF
3 Hourly programming setting (profile)
4 Configurations
5 Room temperature Celsius
6 Menu selection key
Press and hold: ESC (the already changed values are still assigned).
7 Room temperature Fahrenheit
8 On/ Off - Confirm
9 Flat battery
10 NFC phone connection
11 Activation status: air conditioning or heating
12 Temperature read
13 Activation status: Summer or Winter
14 Activation status: economy or comfort
15 DOWN arrow - Decreases
16 UP arrow - Increases
2
8
6
15
16
1 3 4 5
7
91011121314

4
NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
TECHNICAL FEATURES
Battery power supply 2 AA 1.5V alkaline batteries
Battery life >1 year
Temperature regulation scale 2 - 40 °C, increase 0.1°C
Measurement scale/room T display - 50 to + 50 °C, resolution 0.1°C
Type of internal sensor NTC
Relay output with potential-free changeover contacts 5(3)A 230 V~
Terminals COM relay, NC relay, NO relay,
Type of action 1B (micro disconnection)
Conductor rated cross-section for flexible cables: from 0.5 to 1mm2
Connection of cables to terminals Type X
Minimum regulation differential STD (from 0.1 to 0.4 K variable over time)
Reference thermal gradient 4 K/h
Maximum room temperature 45°C
Storage temperature -10°C to +60°C
Rated pulse voltage 4000V
Software class A
NFC yes
Insulation class Class II
Protection rating IP20
Degree of pollution 2
Number of operating cycles for manual actions 3000
Number of operating cycles for automatic actions 10000
Wall-mounting or on recessed box
Dimensions 135 x 83 x 21 mm
Weight 0.100 kg
Compliant with ■EN 60730-1 and second parts
■Directive 2014/53/EU (RED)
■Directive 2014/30/EU (EMC)
■Directive 2014/35/EU (LVD)
ErP classification according to Reg. EU 811/2013 - 813/2013 Class IV; 2%
Product not made in Italy

5
NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
Contents
OPERATION ..................................................................... 2
CONTENTS OF PACKAGE................................................. 2
DESCRIPTION OF DISPLAY KEYS .................................... 3
TECHNICAL FEATURES ................................................... 4
1 - INSTALLATION ........................................................... 6
1.1 - BATTERY REPLACEMENT ....................................................7
2 - ELECTRICAL CONNECTION........................................ 8
3 - PROGRAMMING GUIDE .............................................. 9
3.1 - DATE AND TIME SETTING ....................................................9
3.2 - HOURLY PROGRAMMING SETTING (PROFILE)..................10
4 - OPERATION .............................................................. 11
4.1 - OPERATING PROGRAMS ....................................................11
4.2 - SELECTING THE OPERATING PROGRAM...........................11
4.3 - SETTING THE “AUTO” PROGRAM tE/tC TEMPERATURE ...12
4.4 - SETTING THE “MAN” PROGRAM TEMPERATURE .............12
4.5 - DISPLAYING THE TEMPERATURE WITH THE PROGRAM
“OFF”...........................................................................................12
5 - CONFIGURATION MENU........................................... 13
5.1 - SUMMER/WINTER (default = Winter).................................13
5.2 - CELSIUS / FAHRENHEIT (default = Celsius)......................13
5.3 - DAYLIGHT SAVING / STANDARD TIME (default = Auto) .....14
5.4 - ANTIFREEZE TEMPERATURE (default = 5.0°C) .................14
5.5 - SCREEN LOCK WITH PASSWORD (default = OFF) .............15
5.6 - OFFSET TEMPERATURE (default = 0.0°C) .........................16
5.7 - MAX WINTER TEMPERATURE LIMIT (default = 40°C)........16
5.8 - MIN WINTER TEMPERATURE LIMIT (default = 2°C)..........16
5.9 - MAX SUMMER TEMPERATURE LIMIT (default = 40°C)......17
5.10 - MIN SUMMER TEMPERATURE LIMIT (default = 2°C) ......17
5.11 - RESETTING DEFAULT PARAMETERS (default = rS 0)......18
6 - PROGRAMMING VIA APP.......................................... 19
6.1 - INSTALLATION PROCEDURE .............................................19
6.2 - PROGRAMMING CH119NFC...............................................20
6.3 - GENERAL CH119NFC SETTINGS .......................................22
6.4 - HOME SETTINGS ................................................................30
6.5 - APP SETTINGS: PUSH NOTIFICATIONS .............................30
7 - DISPOSAL................................................................. 31
8 - GENERAL WARRANTY CONDITIONS ........................ 31

mm
mm
mm
6
NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
1 - INSTALLATION
ATTENTION!
Installation must be carried out by qualified personnel in compliance with the requirements concerning
the installation of electrical equipment.
ATTENTION!
Installation operations must be performed with the system’s power disconnected.
The CH119NFC programmable thermostat comes with a panel suitable for wall-mounting or on recessed boxes, with 3
modules or round. It must be installed at a height of about 1.5m from the floor, in a suitable position to detect the room
temperature correctly.
1.5 m
OK
NO NO

21
3 4
1 2 3
7
NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
Undo the screw as shown in figure 1 and release the panel from the appliance.
1.1 - BATTERY REPLACEMENT
Connect to
terminals 1-2

8
NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
2 - ELECTRICAL CONNECTION
ATTENTION!
Electrical connections must be made by qualified personnel.
ATTENTION!
Electrical connection operations must be done with the system’s power disconnected.
Electrical connections must be made by making reference to the following diagram.
During potential blackouts, the parameters will not be lost as the settings are stored in a non-volatile memory. Even
when there are long power failures, the time/date remain stored thanks to an internal battery.
Heat
pump
Connect to
terminals 1-2

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
9
3 - PROGRAMMING GUIDE
The first time any key is pressed has no effect, but only activates the functions of the buttons.
After 30 seconds of no interaction, the display goes back to the main screen.
3.1 - DATE AND TIME SETTING
Note: the SELECTION key makes the icons at the top of the display flash cyclically every time it is pressed. The
icon flashes for 3 seconds, after which, if nothing has been pressed, it goes back to the “initial” mode.
Use the SELECTION key to go to the CLOCK icon and press ENTER.
To edit the HOUR, use the keys
and press ENTER.
Repeat the same operations to edit
the SECONDS.
Repeat the same operations to edit the YEAR.
Repeat the same operations to edit the MONTH.
Repeat the same operations to edit the DAY.
18:30
2
1
3
24.7
:30
10 10:
55
4Y 18
5m 01
6
PRESS
PRESS
PRESS
PRESS
PRESS

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
10
3.2 - HOURLY PROGRAMMING SETTING (PROFILE)
The profiles are set based on whether the WINTER or SUMMER mode is selected.
Note: the SELECTION key makes the icons at the top of the display flash cyclically every time it is pressed. The
icon flashes for 3 seconds, after which, if nothing has been pressed, it goes back to the “initial” mode.
Note: use the arrows to change the time. Use the key to select tE or tC according to the chosen time. By
scrolling through all 24 hours, the next day is displayed.
Note: by pressing the arrows from the day display screen you can choose the day on which to make the
settings directly.
Press the CONFIRM key for 2 seconds to copy the programming of the previous day.
Note: press and hold for 2 seconds to go back to the main screen.
Note: use the arrows to choose the desired comfort temperature. Press CONFIRM to switch to the economy
temperature.
d 01 = Monday
d 02 = Tuesday
d 03 = Wednesday
d 04 = Thursday
d 05 = Friday
d 06 = Saturday
d 07 = Sunday
= Comfort Temperature (tC)
= Economy Temperature (tE)
In Winter
In Summer
Press the SELECTION key 5 times,
then press CONFIRM.
124.7
PRESS
220.0
00:00 00:00
400:00
PRESS
PRESS
303
03
5
20.0
PRESS
PRESS
PRESS
x5
PRESS
24.7

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
11
[ MAN ]
■MANUAL PROGRAM
The device adjusts the room temperature by using a set temperature
specified each time, for an unlimited amount of time, until another
program is selected.
[ AUTO ]
■WEEKLY PROGRAM
The device manages the set Economy and Comfort temperatures
depending on the hourly programs.
[ OFF ]
■SYSTEM OFF or ANTIFREEZE PROGRAM
Press the OFF key to switch off the system. During WINTER mode, it
maintains the antifreeze temperature.
Note: the SELECTION key makes the icons at the top of the display flash
cyclically every time it is pressed. The icon flashes for 3 seconds, after
which, if nothing has been pressed, it goes back to the “initial” mode.
Note: if the confirm button is not pressed, you go back to the “initial” mode.
Note: if the confirm button is not pressed, you go back to the “initial” mode.
4 - OPERATION
The CH119NFC programmable thermostat is a device that controls cooling and heating systems.
4.1 - OPERATING PROGRAMS
The CH119NFC programmable thermostat has different operating modes, called programs.
4.2 - SELECTING THE OPERATING PROGRAM
The programs are selected by cyclic sequence.
Program selection [AUTO]
Press the SELECTION key 3 times,
then press CONFIRM.
Press the SELECTION key twice,
then press CONFIRM.
Program selection [MAN]
Press the SELECTION key 4 times,
then press CONFIRM.
Note: if the confirm button is not pressed, you go back to the “initial” mode.
Program selection [OFF]
24.7
24.7
24.7
5.0
24.7
1
PRESS
x2 24.7
PRESS
24.7
224.7
PRESS
x3
PRESS
24.7
324.7
PRESS
x4
PRESS

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
12
4.3 - SETTING THE “AUTO” PROGRAM tE/tC TEMPERATURE
Note: it is not necessary to press the confirm key. After 2 seconds the chosen value is set.
4.4 - SETTING THE “MAN” PROGRAM TEMPERATURE
Note: it is not necessary to press the confirm key. After 2 seconds the chosen value is set.
4.5 - DISPLAYING THE TEMPERATURE WITH THE PROGRAM “OFF”
Note: the set tA is displayed. It is not possible to change the tA from this menu.
Note: use the arrows to change the temperature value tE or tC (depending on whether tE or tC is set). Pressing
the key once does not change the value but displays the set point. In winter tE < tC; in summer tC < tE
Note: use the arrows to change the current manual temperature value. Pressing the key once does not change
the value but displays the set point.
Comfort Temperature (tC) =
Economy Temperature (tE) =
24.7
1
218.5
24.7
1
221.2
24.7
1
5.0
2

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
13
5.2 - CELSIUS / FAHRENHEIT (default = Celsius)
Use the arrow keys until reaching P02, then press CONFIRM.
5 - CONFIGURATION MENU
From this menu, it is possible to change certain configuration parameters of CH119NFC.
Note: the SELECTION key makes the icons at the top of the display flash cyclically every time it is pressed. The icon
flashes for 3 seconds, after which, if nothing has been pressed, it goes back to the “initial” mode.
P 01 = summer/winter selection
P 02 = °C/°F selection
P 03 = daylight saving time/standard time selection
P 04 = tA setting
P 05 = screen lock with password setting
P 06 = temperature offset setting
P 07 = Max / Winter temperature limit setting
P 08 = Min / Winter temperature limit setting
P 09 = Max / Summer temperature limit setting
P 10 = Min / Summer temperature limit setting
P 11 = default parameters reset
5.1 - SUMMER/WINTER (default = Winter)
or
This allows you to choose the temperature display scale between Celsius and Fahrenheit degrees.
Use the arrow keys to
select the parameter to edit.
Press CONFIRM to edit a parameter.
SU = summer
WN = winter
Select the season and press CONFIRM.
124.7 P 01
2P 01
PRESS
1P 01
PRESS
2SU WN
PRESS
PRESS
x6
PRESS
1P 01
PRESS
2P 02

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
14
or
5.3 - DAYLIGHT SAVING / STANDARD TIME (default = Auto)
or
5.4 - ANTIFREEZE TEMPERATURE (default = 5.0°C)
Note: the tA that can be set is between 2.0 and 7.0 °C or OFF = “----”, and it can only be enabled in winter.
CEL = Celsius
FAH = Fahrenheit
Use the arrow keys until reaching P03, then press CONFIRM.
AUTO = Automatic
MAN = Manual
Use the arrow keys until reaching P04, then press CONFIRM.
Automatically selects daylight saving time, applicable in Europe and some other countries. This set-up automatically
updates the time when it changes (March and October).
3CEL FAH
PRESS
1P 01
PRESS
3AUTO MAN
PRESS
2P 03
1P 01
PRESS
35.0
PRESS
2P 04

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
15
5.5 - SCREEN LOCK WITH PASSWORD (default = OFF)
or
Note: confirming ON allows you to set the password. Continue to follow this paragraph.
Selecting OFF does not set the screen lock with password.
Note: enter the 4 digits of the password to unlock the device. In the event of an error, the message LOC appears
again and the device remains locked.
Use the arrow keys until reaching P05, then press CONFIRM.
ON = Screen lock on
OFF = No screen lock
Password Setting
When the screen is locked, LOC will be displayed when pressing the or SELECTION keys.
To unlock the screen
Press CONFIRM and repeat the operation from point 4.
Note: a blackout does not reset the password.
It allows you to lock the CH119NFC keyboard with a 4-digit code. It only works once and then must be re-enabled.
1P 01
PRESS
3OFF
PRESS
2P 05
ON
40000
PRESS
3000
3
PRESS
33 002
PRESS
33 205
PRESS
524.7 LOC
PRESS
0000
PRESS

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
16
Note: offset value that can be set is between -5.0 and 5.0°C
5.6 - OFFSET TEMPERATURE (default = 0.0°C)
5.7 - MAX WINTER TEMPERATURE LIMIT (default = 40°C)
Note: default value 40.0°C, value that can be set is between 2.0 and 40.0°C
5.8 - MIN WINTER TEMPERATURE LIMIT (default = 2°C)
It allows you to edit the temperature measured from CH119NFC. Due to incorrect wall-mounting installation (behind
walls, curtains or in crannies), the sensor might not indicate the correct temperature perceived by the device. This
function corrects the temperature measured ± 5.0 °C.
Use the arrow keys until reaching P06, then press CONFIRM.
Use the arrow keys until reaching P07, then press CONFIRM.
It allows you to limit the maximum set point temperature that can be set in winter.
It allows you to limit the minimum set point temperature that can be set in winter.
1P 01
PRESS
2P 06
30.0
PRESS
1P 01
PRESS
2P 07
340.0
PRESS
1P 01

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
17
Note: default value 2.0°C, value that can be set is between 2.0°C and the value set in P7 minus 0.1°C (if you set
P7 with a value of 25.0°C, the maximum value that can be set in P8 will be 24.9°C)
5.9 - MAX SUMMER TEMPERATURE LIMIT (default = 40°C)
Note: default value 40.0°C, value that can be set is between 2.0 and 40.0°C
5.10 - MIN SUMMER TEMPERATURE LIMIT (default = 2°C)
Note: default value 2.0°C, value that can be set is between 2.0°C and the value set in P9 minus 0.1°C (if you set
P9 with a value of 20.0°C, the maximum value that can be set in P10 will be 19.9°C)
Use the arrow keys until reaching P08, then press CONFIRM.
Use the arrow keys until reaching P09, then press CONFIRM.
Use the arrow keys until reaching P10, then press CONFIRM.
It allows you to limit the maximum set point temperature that can be set in summer.
It allows you to limit the minimum set point temperature that can be set in summer.
PRESS
2P 08
32.0
PRESS
1P 01
PRESS
2P 09
340.0
PRESS
1P 01
PRESS
2P 10
32.0
PRESS

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
18
5.11 - RESETTING DEFAULT PARAMETERS (default = rS 0)
Use the arrow keys until reaching P11, then press CONFIRM.
rS 0 = no RESET
rS 1 = RESET
This allows you to reset all the parameters (except date and time) to the factory settings.
1P 01
PRESS
2P 11
3S 1
PRESS
PRESS

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
19
6 - PROGRAMMING VIA APP
Download the Intelliclima+ APP available free of charge on Google Play Store.
Note: you must have an Android smartphone with NFC technology.
Add a new house by pressing
■
or
■go to GENERAL SETTINGS and
press ADD HOUSE.
Enter the name of the HOUSE desired
and press .
6.1 - INSTALLATION PROCEDURE
Add the programmable thermostat
by pressing and select
CH119NFC.
Follow the installation wizard.
Install the APP and, when first
activated, create an account
by entering the user name and
password (an active data connection
is required for this operation).
Note: CH119NFC can also work
without a WI-FI connection. In this
case, tick GSM Mode.
2
1
3
4

NFC WEEKLY PROGRAMMABLE THERMOSTAT
CH119NFC
20
6.2 - PROGRAMMING CH119NFC
1 Home name
2 Room name
3 Season
4 Current set point
5 General APP settings
6 Home settings
7 General Thermostat settings
8 CH119NFC update status
9 Last CH119NFC update date
10 Operating mode
5
1
2
3
4
5
6
7
8
9
10