Fantini Cosmi CH180T3K5 User manual

CH180T3K5
WIRELESS TEMPERATURE CONTROL KIT
4 TEMPERATURE AREAS
INSTRUCTIONS FOR USE
FANTINI COSMI S.p.A.
Via dell’Osio, 6 20090 Caleppio di Settala, Milan – ITALY
Tel. [phone] | Fax [phone] | inf[email protected]
www.fantinicosmi.it

2
4 TEMPERATURE AREA WIRELESS TEMPERATURE CONTROL KIT
CH180T3K5
Thank you for purchasing a FANTINI COSMI S.p.A. product
Please read this instruction manual carefully and always keep it handy should you need to consult it for any
reason.
The documentation reflects the characteristics of the product. However, for regulatory or commercial
developments, customers should verify the availability of updates relating to this documentation on the
FANTINI COSMI S.p.A. website: pdf.fantinicosmi.it
OPERATION
The pre-configured CH180RFWIFI programmable thermostat acts as a supervisor for the Intellicomfort+ wireless
multi-zone system by controlling the 4 areas of the home, interacting with the CH120RF room thermostats and
O60RF wireless radiator actuators. The components, which are already preconfigured, are divided as follows:
■area 1 = 1 CH180RFWIFI + 2 O60RF;
■area 2 = 1 CH120RF + 1 O60RF;
■area 3 = 1 CH120RF + 1 O60RF;
■area 4 = 1 CH120RF + 1 O60RF.
The CH180RFWIFI “MASTER” programmable thermostat directly controls the O60RF radiator actuators of area 1;
In other areas, it sends the time profiles to the associated CH120RF thermostats. The thermostats, based
on the detected room temperature, send the commands to the O60RF actuators on the radiators.
CONTENTS OF PACKAGE
■no. 1 wireless weekly programmable thermostat with WiFi connection, code CH180RFWIFI
■no. 3 wireless room thermostats, code CH120RF
■no. 5 wireless radiator actuators, code O60RF
■no. 1 user instruction sheet
Area 1
Area 3 Area 4
Area 2
O60RF
(PR2)
O60RF
(PR1)
O60RF
(PR1)
O60RF
(PR1)
O60RF
(PR1)
CH120RF CH120RF
CH120RF
CH180RFWIFI

3
4 TEMPERATURE AREA WIRELESS TEMPERATURE CONTROL KIT
CH180T3K5
START-UP
ATTENTION!
Installation must be done by qualified personnel in compliance with the requirements
concerning installation of electrical equipment. Installation operations must be performed
with the system’s power disconnected.
Install the programmable thermostat in area 1
Install the thermostats, without batteries, in areas 2, 3 and 4
1
2
The CH180RFWIFI programmable thermostat must be installed on the wall or on a flush mounting box,
in 3 units or round, at a height of about 1.5m from the floor, in a suitable position to detect the room
temperature correctly.
For installation, refer to the QUICK GUIDE contained in the programmable thermostat package
CH180RFWIFI.
The CH120RF thermostats must be installed on the wall or on a flush mounting box, in 3 units or round,
at a height of about 1.5m from the floor, in a suitable position to detect the room temperature correctly.
For installation, refer to the QUICK GUIDE contained in the CH120RF thermostat package.
Install the O60RF actuators, without batteries, on the radiators, as indicated in the instruction sheet
contained in their packaging.
Be sure to position each O60RF in the correct area (as indicated in the label on the product).
EXAMPLE
Actuator to be installed in area 2
Thermostat to be installed in area 2
Z : _
2
3
Be sure to position each CH120RF in the correct area (as indicated in the label on the product).
EXAMPLE
Z : _
2

FANTINI COSMI S.p.A.
Via dell’Osio, 6 20090 Caleppio di Settala, Milan – ITALY
Tel. [phone] | Fax [phone] | inf[email protected]
www.fantinicosmi.it
5679931 - 02/2019
Insert batteries into the thermostats and actuators
If you want to control the CH180RFWIFI remotely via APP from smartphone or tablet, download
the INTELLICLIMA+ App.
To install the APP, refer to the CH180RFWIFI instruction sheet, downloadable from
FANTINI COSMI S.p.A. : pdf.fantinicosmi.it
5
6
The Intelliclima+ app is available for free on:
Power the programmable thermostat and set the [ MAN ] manual program mode
4