Felton RW User manual

REGAL OVER THE BATH SHOWER UNIT
The Regal is designed to convert an existing bath into a bath/shower. It attaches to existing taps
and requires only the simplest of tools.
INSTALLATION GUIDE
REGAL OVER THE BATH SHOWER UNIT RW | RWE | RWH
WHAT IS IN THE PACK
1 x Designer II Feltonmix® Wallset
White (WWSD2) & screw pack
1 x Regal cover
(800 x 300mm)
2 x adaptors
with bushes
2 x adaptor covers
1 x Feltonmix® Mixing
Valve & screw pack
1 x pipe set (1500mm
long pipes with fittings)
1 x Screw pack with
plastic toggle, cap & cover
1 x roll of Ceelon thread
seal tape
1 x Bag of restrictors with
fitting instructions
For technical assistance please ring: 0800 743 358 or [phone]
Felton Industries Limited 8 Farmhouse Lane, Saint Johns, Auckland 1072 New Zealand www.felton.co.nz
Warranty, Maintenance and Care YOUR COPY TO KEEP
Felton Industries Limited guarantees these mixers to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase. Fair wear and tear
is expressly excluded. This warranty is eective for 5 years from the date of purchase for the supply of replacement parts only, not including installation. You must retain proof of
purchase of the Mixer (such as an invoice or receipt) and provide this to Felton on request. This warranty is for manufacturing defects only and does not cover any damage to the
product due to abuse, negligence or improper installation. This warranty is given on the understanding that the product is installed and operated according to Felton’s installation
guide and the Australian/New Zealand standard AS/NZS3500. This warranty is provided to persons who are a “consumer” under the Consumer Guarantees Act 1993 only and for
use in domestic/residential dwellings only (not for commercial use).
At no stage should any surface coatings be cleaned with cleaning agents that contain a corrosive acid or a scouring additive. Surface coatings should be cleaned with
liquid detergent or soap and water. Any damage caused through the use of an unsuitable cleaner will not be covered by this warranty. This warranty is subject to any
other rights or remedies that you may have under the Consumer Guarantees Act 1993 (or any other applicable legislation) and to Felton’s Terms of Trade.
Please fill in the details below, attach your receipt to this installation guide and keep as your proof of purchase.
Purchased at:
Date of purchase:
Installed by:
070622EI

INSTALLATION INSTRUCTIONS
1. Turn o the water at the mains. Remove bath taps and re-install with tap adaptors and covers fitted behind
them. Adaptors are provided with a bush to accommodate ¾” or ½” BSP threads. Seal threads with Ceelon
thread tape.
2. Mount shower mixing valve on wall at desired height (not exceeding 1500mm above taps). Add an additional
5-6mm to the calculated pipe length to allow for bends to reach taps.
3. Connect pipes between shower valve isolators and bath tap adaptors. Fit white sleeve at bottom of pipe
using long nuts. Connect hot water to red shower valve isolator, cold water to blue. If hot and cold water pipes
are reversed, turn shower valve through 180° and rotate isolators to point downwards.
4. Check that there are no leaks to shower valve by closing isolators and turning on mains. Test further for leaks
as follows:
a. Fit shower handle and turn anticlockwise to OFF position.
b. Turn on isolators. All joints must be watertight.
5. To complete installation of shower valve,
a. Remove shower handle.
b. Remove protective plastic film from Regal cover and fit it and the wallplate to shower valve.
c. Fit handle and screw in shower head.
d. Attach base of Regal cover using screw, cap and cover supplied. Use plastic toggle if
e. fastening to wallboard, brick or block.
6. For Mains Pressure fit white restrictor using tool as directed into stem of showerhead.
Cover
Feltonmix® Mixing Valve
Two-way adaptor
3/4” to 1/2” brass reducing bush
Regal Cover
Feltonmix® Wallset
Pipe set & fittings