Felton USMC User manual

INSTALLATION GUIDE
MAXIMUM STATIC PRESSURE
Maximum static pressure 700kPa. If the water pressure exceeds or is likely to exceed 700kPa, an
approved pressure limiting valve must be tted.
MINIMUM STATIC PRESSURE
HOT COLD
Mains Pressure 150kPa 150kPa
Unequal Pressure 36kPa 150kPa
Equal Low Pressure 36kPa 36kPa
System Requirements
To ensure the optimum performance and customer satisfaction please adhere to the following:
•Flush out all pipework prior to installation.
• Maximum hot water temperature: 80°C. If the water temperature exceeds 80°C an approved tempering
valve must be fitted.
• Installation should comply with relevant local authority requirements.
• In accordance with good plumbing practice, filters should be fitted to supply lines to eliminate damage
to the ceramic cartridge from suspended solids.
Urban Sink Mixer
(USMC)
Ensure that the brown or yellow plastic regulator supplied is tted to the brass nipple and tted to the cold
supply hose. Remove the “aerator” tting from the mixer outlet and replace it with the ow straightener
provided.
Unequal Pressure
Ensure that any brown plastic regulators are removed from the brass nipples. Remove the “aerator” tting
from the mixer outlet and replace it with the ow straightener provided.
Equal Low Pressure
Mains Pressure
Ensure that the 2 pink plastic regulators supplied are tted to the brass nipples and tted to both supply hoses.
1 x sink mixer 2 x brass nipples 1 x brown or yellow regulator
1 x hot supply hose 1 x ow straightener 2 x pink regulators
1 x cold supply hose 1 x sink xings
Contents of Pack

280514VC
1. Cut a mounting hole 35mm in diameter. There must be a minimum 15mm width of at around the hole.
2. Fit benchtop rubber seal onto benchtop around 35mm hole.
3. Screw the two threaded studs into the mixer base.
4. Screw the “HOT” supply hose (with red marking) into mixer base hole ‘H’ (with red marking)
5. Screw the “COLD” supply hose (unmarked) into the last hole in the mixer base.
6. Lower the tted hoses, one hose at a time, into mounting hole.
7. From UNDERNEATH the bench, t ‘C’ rubber washer (if supplied), and metal washer around both hoses
and over the threaded stud.
8. Screw on the two M6 nuts and tighten with your ngers.
9. Check the mixer and the benchtop seal are correctly aligned on the bench. Secure with spanner.
10. Flush the supply pipes to remove debris.
11. Connect the water supply and check all the ttings are tight.
12. Turn on water supply and check for leaks.
Mixer Installation
Maximum bend for flexible hose is 35mm radius. The nipples on the hoses must be con-
nected to fittings which have machined end faces, not “sawn off” threaded tube.
Warranty, Maintenance & Care - USMC
For technical assistance please ring: 0800 743 358 or [phone]
Felton Industries Limited - 8 Farmhouse Lane Glen Innes Auckland 1072 New Zealand www.felton.co.nz
Felton Industries Limited guarantees these mixers to be free from defects in materials and workmanship for a period of ten (10) years
from the date of purchase.
This warranty is effective for 10 years from the date of purchase and covers supply of replacement parts only and 5 years of plumbers
labour relating solely to repairing or replacing the mixer from the date of purchase, provided the product is installed by a registered
plumber. You must retain proof of purchase of the Mixer (such as an invoice or receipt) and proof of installation by a registered plumber
and provide these to Felton on request.
This warranty is for manufacturing defects only and does not cover any damage to product due to abuse, negligence or improper
installation. This warranty is given on the understanding that the product is installed by a registered plumber and operated according
to Felton’s installation guide and the Australian/New Zealand standard AS/NZS3500. This warranty is provided to persons who are a
“consumer” under the Consumer Guarantees Act 1993 only and for use in domestic/residential dwellings only (not for commercial use).
Please ll in the details below, attach your receipt to this installation guide and keep as your proof of purchase.
Purchased at:
Date of purchase:
Installed by:
At no stage should plated surfaces be cleaned with cleaning agents that contain a corrosive acid or a scour-
ing additive. Plated surfaces should be cleaned with liquid detergent or soap and water. Any damage caused
through the use of an unsuitable cleaner will not be covered by warranty.
This warranty is subject to any other rights or remedies that you may have under the Consumer Guarantees Act
1993 (or any other applicable legislation) and to Felton’s Terms of Trade.