Festool ECU 45 User manual

ECU 45
Bedienungsanleitung Ladegerät 4 - 5
Operating Instructions Charger 6 - 7
Mode demploi Chargeur 8 -9
Instrucciones de servicio Cargador 10 - 11
Istruzioni duso Caricatore 12 - 13
Gebruiksaanwijzing Oplaadapparaat 14 - 15
Bruksanvisning Laddningsaggregatet 16 - 17
Käyttöohje Latauslaitetta 18 - 19
Driftsvejledning Batteriladeren 20 - 21
Bruksanvisning Ladeapparatet 22 - 23
Instruções de uso Carregador 24 - 25
Ðóêîâîäñòâî ïî ýêñïëóàòàöèè Çàðÿäíûå óñòðîéñòâà 26 - 27
Návod k obsluze Rychlonabíjecí pøístroj 28 - 29
Instrukcja obs³ugi £adowarka 30 - 31
Kezelési utasítás Töltõkészülékbõl 32 - 33
Ïäçãßá ëåéôïõñãßáò ÓõóêåõÞ öüñôéóçò 34 - 35
Festool GmbH Wertstr. 20 D-73240 Wendlingen (07024/804-0
463 278_001
Seen at Ideal Tools.

CE-Konformitetserklæring. Vi erklærer på eget ansvar
at dette produktet er i overensstemmelse med
følgende normer eller normative dokumenter:
EN 60 335, EN 55 014, EN 60 555 i henhold til bestemmelsene
i direktivene 73/23/EØF, 89/336/EØF.
CE-Konformitätserklärung. Wir erklären in alleiniger
Verantwortung, dass dieses Produkt mit den
folgenden Normen oder normativen Dokumenten
übereinstimmt: EN 60 335, EN 55 014, EN 60 555 gemäß den
Bestimmungen der Richtlinien 73/23/EWG, 89/336/EWG.
453 638_001
CE-konformitetserklæring: Vi erklærer at have alene
ansvaret for, at dette produkt er i overensstemmelse
med de følgende normer eller normative dokumenter:
EN 60 335, EN 55 014, EN 60 555 i henhold til bestemmelserne
af direktiverne 73/23/EØF, 89/336/EØF.
CE-standardinmukaisuusvakuutus. Vakuutamme
yksinvastuullisina, että tuote on seuraavien
standardien ja normatiivisten ohjeiden mukainen: EN 60 335,
EN 55 014, EN 60 555 direktiivien 73/23/EU, 89/336/EU
määräysten mukaan.
CE-konformitetsförklaring. Vi förklarar i eget ansvar,
att denna produkt stämmer överens med följande
normer och normativa dokument: EN 60335, EN 55 014,
EN 60 555 enligt bestämmelserna i direktiven 73/23/EEC,
89/336/EEC.
CE-conformiteitsverklaring. Wij verklaren op eigen
verantwoordelijkheid dat dit produkt voldoet aan de
volgende normen of normatieve documenten. EN 60 335,
EN 55 014, EN 60 555 conform de richtlijnen 73/23/EEG,
89/336/EEG.
Dichiarazione di conformità CE. Dichiariamo sotto la
nostra esclusiva responsabilità che il presente
prodotto è conforme alle norme e ai documenti normativi
seguenti: EN 60 335, EN 55 014, EN 60 555 conformemente
alle normative delle direttive 73/23/CEE, 89/336/CEE.
Declaración de conformidad CE. Declaramos bajo
nuestra exclusiva responsabilidad que este producto
corresponde a las siguientes normas o documentos
normalizados: EN 60 335, EN 55 014, EN 60 555, conforme a
las prescripciones estipuladas en las directrices
73/23/CEE, 89/336/CEE.
Déclaration de conformité communautaire. Nous
déclarons sous notre propre responsabilité que ce
produit est conforme aux normes ou documents de
normalisation suivants: EN 60 335, EN 55 014, EN 60 555
conformément aux prescriptions des directives 73/23/CEE,
89/336/CEE.
EC-Declaration of Conformity: We declare at our sole
responsibility that this product is in conformity with
the following standards or standardised documents:
EN 60 335, EN 55 014, EN 60 555 in accordance with the
regulations 73/23/EEC, 89/336/EEC.
Declaração de conformidade CE: Declaramos, sob
a nossa exclusiva responsabilidade, que este
produto corresponde às normas ou aos documentos
normativos citados a seguir: EN 60 335, EN 55 014,
EN 60 555 segundo as disposições das directivas
73/23/CEE, 89/336/CEE.
Çàÿâëåíèå î êîíôîðìíîñòè ÑÅ. Ìû çàÿâëÿåì â
åäèíîëè÷íîé îòâåòñòâåííîñòè, ÷òî äàííîå èçäåëèå
ñîîòâåòñòâóåò òðåáîâàíèÿì ñëåäóþùèõ ñòàíäàðòîâ èëè
íîðìàòèâîâ: EN 60 335, EN 55 014, EN 60 555 â ñîîòâåòñòâèè
ñ ïîñòàíîâëåíèÿìè äèðåêòèâ ÅÝÑ 73/23, ÅÝÑ 89/336.
Prohláení o souladu s normami ES. Prohlaujeme
na vlastní zodpovìdnost, e tento výrobek odpovídá
následujícím normám nebo normativním dokumentùm:
EN 60 335, EN 55 014, EN 60 555 v souladu s ustanoveními
smìrnic 73/23/EHS, 89/336/EHS.
Owiadczenie o zgodnoci CE. Niniejszym
owiadczamy z ca³¹ odpowiedzialnoci¹, ¿e wyrób
ten odpowiada nastêpuj¹cym normom wzglêdnie dokumentom
normatywnym : EN 60 335, EN 55 014, EN 60 555 zgodnie z
postanowieniami wytycznych 73/23/EWG, 89/336/EWG.
Äçëùóç óõììüñöùóçò ÅÏÊ. Ìå áíÜëçøç ôçò
óõíïëéêÞò åõèýíçò äçëþíïõìå, üôé ôï ðáñüí ðñïéüí
óõìöùíåß ìå ôá ðáñáêÜôù ðñüôõðá êáé ìå ôá ðñüôõðá ðïõ
áíáöÝñïíôáé óôá ó÷åôéêÜ Ýããñáöá ÅÍ 60 335, ÅÍ 55 014,
EN 60 555 óýìöùíá ìå ôïõò êáíïíéóìïýò 73/23 ÅÏÊ,
89/336/ÅÏÊ.
CE-konformitás-nyilatkozat. Kizárólagos felelõs-
ségvállalás mellett ezennel tanúsítjuk, hogy a jelen
termék megfelel az alábbi szabványoknak ill. szabvány-
dokumentációnak: EN 60 335, EN 55 014, EN 60 555 a
73/23/EWG, 89/336/EWG irányvonalak rendelkezései szerint.
Leitung Forschung und Entwicklung
Management Research and Development
Direction de recherce et développement
Festool GmbH
Wertstr. 20
D-73240 Wendlingen
Dr. Johannes Steimel
Seen at Ideal Tools.

Seen at Ideal Tools.

6
Technical data ECU 45
Supply voltage (input) 230 - 240 V ~
Line frequency 50/60 Hz
Charging voltage (output) 7.2  14.4 V (DC)
Charging current
Quick charge max. 3 A
Compensation charge pulsating app. 0.06 A
Charging time for
NiCd 1.4 Ah app. 38 min
NiCd 1.7 Ah app. 42 min
NiCd 2.0 Ah app. 46 min
NiMH 3.0 Ah app. 70 min
Weight 0.5 kg
The illustrations mentioned can be found on a fold-
out page at the beginning of the operating
instructions.
1Directions for use
The charger ECU 45 has been designed to charge
the battery packs specified under Chapter 2.
The user will be liable for damage due to improper
use.
For your own safety
Repairs may only be carried out by qualified
experts. Warning: ECU 45 charging device: Even
after disconnection from the mains, there is still a
high capacitor voltage on the power output
component on the inside of the device.
Protect equipment against moisture.
Do not use the charger if the connecting cable is
damaged, unplug immediately from the main.
Protect the cable against heat, oil and sharp
edges.
Never carry the tool by its cable and never use to
the cable to pull the plug out of the wall socket.
Do not use defect and damaged battery packs.
Only use original Festool battery packs. Do not
use spent and recycled battery packs. The user
shall be liable for damages if Festool original
battery packs are not used.
Do not place spent battery packs into fire or into
domestic waste. Attention: Festool offers an
ecological friendly waste disposal for used battery
packs (refer to RECYCLING OF BATTERY
PACKS).
Do not open battery packs.
Do not store battery packs with metal objects
(danger of short circuit).
No metal objects (metal chips) should enter the
charger at the contact points as well as through
the cooling slits into the equipment (danger of
short circuit).
Keep out of reach of children.
Check the tool for damages before use. Have
damaged parts repaired or replaced by the
customer service department.
2Charge battery pack
All NiCd and NiMH battery packs between 7.2 V
and 14.4 V voltage can be charged with the
ECU 45 charger.
The battery type used (NiCd or NiMH) is detected
automatically. Charging is controlled by a
microprocessor.
Warning: If a warm NiMH battery pack (>37°C) is
inserted, charging will only be carried out at a lower
charge current.
In this case the charging time for a battery pack
with 3.0 Ah is around 100 min..
By the influence of powerful electromagnetic
perturbations while charging it can be switched over
to conservation charge.
Thereby the charger can not take in a dangerous
or unsafe status
The LED (1.10) shows the charge status of the
charger.
LED yellow - steady
= Charger is ready for use.
LED green - flashing
= Battery pack being charged.
LED green - steady
= Battery pack fully charged, conservation charge
on.
LED red - flashing
= General malfunction, e. g. full contact not being
made, short-circuit, battery pack faulty.
LED red - steady
= Temperature of battery pack is outside
permissible limit (5° - 45°C).
Charging
Connect charger to mains.
Warning: The line voltage and frequency must
correspond with the data on the ratings plate!
Insert battery pack into charging chamber:
Insert battery pack with the fin (1.4 or 1.5) in the
lower groove (1.1) of the charging chamber.
Push battery pack into charging chamber until it
catches with the lock (1.9 or 1.7) in the groove (1.2
or 1.3). The battery pack is now charged.
Press the button (1.8 or 1.6) to unlock it and remove
it from the charger.
Seen at Ideal Tools.

7
3 Wall mounting
The charger ECU 45 has two longitudinal slots on
its rear by which it can be suspended on walls using
two screws (e.g. button-headed or flat head screw
with a shaft diameter of 5 mm).
Screw the screws into the wall so that their heads
protrude approx. 4 mm.
4lnstructions on application -
maintenance - care
The equipment is generally maintenance-free.
To ensure trouble-free operation we recommend
that the following instructions be adhered to:
Keep the air vents clean to guarantee the air
circulation for cooling.
Keep the connection contacts clean.
Festool chargers and Festool battery packs are
designed for each other. Therefore, only use
Festool chargers to charge Festool battery
packs.
By keeping the battery pack in a ready for use
charger, the battery pack will be kept in a state of
readiness by float charging conservation.
Do not keep discharged battery pack (maximum
one month) attached to charger whenever charger
is detached from the power supply (danger of
deep discharging).
Whenever two battery packs are inserted into the
quick charger they will be charged in the order of
insertion.
A new battery pack or a battery pack not used for
a longer period of time reaches it full capacity after
about 5 charging and discharging cycles.
Battery packs should, before charging, be fully
discharged if possible. Continuous starting of the
charging process shortens the lifespan of the
batteries.
Do not expose battery packs to direct rays of the
sun or high temperatures - Temperatures over
45°C will shorten the life of the battery.
All maintenance and repair work, requiring
dismantling of equipment, may only be performed
by an authorised after-sales service workshop.
5Recycling battery packs
Never throw spent battery packs into domestic
waste containers!
Return spent or defective battery packs to dealers,
the Festool after-sales service department or
approved waste disposal facilities.
This ensures that they are correctly recycled.
6 Warranty
Our equipment is under warranty for at least 12
months with regard to material or production faults
in accordance with national legislation.
In the EU countries, the warranty period is 24 months
(an invoice or delivery note is required as proof of
purchase).
Damage resulting from, in particular, normal wear
and tear, overloading, improper handling, or caused
by the user or other damage caused by not
following the operating instructions, or any fault
acknowledged at the time of purchase, is not
covered by the warranty.
Complaints will only be acknowledged if the
equipment has not been dismantled before being
sent back to the suppliers or to an authorised
Festool customer support workshop.
Store the operating instructions, safety notes, spa-
re parts list and proof of purchase in a safe place.
In addition, the manufacturers current warranty
conditions apply.
Note
We reserve the right to make changes to the
technical data contained in this information as a
result of ongoing research and development work.
The plastic material of this product is provided with
a material marking to secure a controlled recycling.
Seen at Ideal Tools.

Festool GmbH
Postfach 1163
D-73236 Wendlingen
Wertstraße 20
D-73240 Wendlingen
)(07024) 804-0
Fax [phone]
http://www.festool.com
Seen at Ideal Tools.