FIBARO FGK-10x User manual

FIBARO DOOR/WINDOW SENSOR
FGK-10x
CONTENTS
#1: Description and features 4
#2: Basic activation 5
#3: Adding/removing the device 6
#4: Temperature sensor 7
#5: Button or external sensor 8
#6: Physical installation 9
#7: Operating the device 10
#8: Association 12
#9: Advanced parameters 13
#10: Specications 19
#11: Regulations 20
OPERATING
MANUAL EN
v2.0

3
Important safety information
Read this manual before attempting to install the device!
Failure to observe recommendations included in this manual
may be dangerous or cause a violation of the law. The manufacturer,
Fibar Group S.A. will not be held responsible for any loss or damage
resulting from not following the instructions of operating manual.
!
General information about
the FIBARO System
FIBARO is a wireless smart home automation system, based on the
Z-Wave protocol. All of available devices can be controlled through
a computer (PC or Mac), smartphone or tablet. Z-Wave devices are
not only receivers, but can also repeat the signal, increasing the
Z-Wave network’s range. It gives advantage over traditional wireless
systems that require direct link between transmitter and receiver, as
a result the construction of the building could aect network’s range
negatively.
Every Z-Wave network has its unique identication number (home
ID). Multiple independent networks can exist in the building without
interfering. Transmission security of FIBARO System is comparable to
wired systems.
Z-Wave technology is the leading solution in smart home automation.
There is a wide range of Z-Wave devices that are mutually
compatible, independently of manufacturer. It gives the system the
ability to evolve and expand over time. For more information visit:
www.baro.com.

4
DESCRIPTION AND FEATURES
Main features of FIBARO Door/Window Sensor:
• Compatible with any Z-Wave or Z-Wave+ Controller,
• Supports protected mode (Z-Wave network security mode) with
AES-128 encryption,
• Door/window opening detected through separation of Sensor’s
body and a magnet,
• Easily mounted on doors, windows, garage gates and roller blinds,
• Battery powered,
• Visual LED indicator signalling status of the device,
• Compatible with the DS18B20 temperature sensor,
• Potential-free input allowing to connect a button or binary sensor.
FIBARO Door/Window Sensor is a wireless, battery powered reed
sensor compatible with the Z-Wave standard. Changing the device’s
status will automatically send signal to the Z-Wave controller and
associated devices.
Sensor can be used to trigger scenes and everywhere there is a need
for information about opening or closing of doors, windows, garage
doors, etc. Opening is detected by separating the sensor’s body and
the magnet.
In addition the FIBARO Door/Window Sensor supports one DS18B20
temperature sensor and has one potential free input.
#1: Description and features
FIBARO Door/Window Sensor is
a fully compatible Z-Wave PLUS
device.
NOTE
This device may be
used with all devices
certied with Z-Wave
Plus certicate and
should be compatible
with such devices pro-
duced by other manu-
facturers.
i
NOTE
FIBARO Door/Window
Sensor is a Security
Enabled Z-Wave Plus
product and a Secu-
rity Enabled Z-Wave
Controller must be
used in order to fully
utilize the product.
i

5
BASIC ACTIVATION
#2: Basic activation
1. Open the cover.
2. Remove the battery blocker.
3. Close the cover.
4. Add the device (see “Adding/removing the device” on page 6).
5. Install the device (see “Physical installation” on page 9).
NOTE
The antenna should
be placed above the
battery. Never cut,
shorten or bend the
antenna. Its length is
suited to the band at
which the system op-
erates.
i
NOTE
Metal surfaces in close
vicinity (e.g. metal
switch boxes, metal
door trims) may im-
pair the reception ca-
pability.
i

6
ADDING/REMOVING THE DEVICE
#3: Adding/removing the device
Adding (Inclusion) - Z-Wave device learning mode, allowing to add
the device to existing Z-Wave network.
To add the device to the Z-Wave network:
1. Close the cover.
2. Place the Door/Window Sensor within the direct range of your
Z-Wave controller.
3. Set the main controller into (security/non-security) add mode (see
the controller’s manual).
4. Quickly, three times press the TMP button.
5. Wait for the adding process to end.
6. Successful adding will be conrmed by the Z-Wave controller’s
message.
Removing (Exclusion) - Z-Wave device learning mode, allowing to
remove the device from existing Z-Wave network.
To remove the device from the Z-Wave network:
1. Close the cover.
2. Place the Door/Window Sensor within the direct range of your
Z-Wave controller.
3. Set the main controller into remove mode (see the controller’s
manual).
4. Quickly, three times press the TMP button.
5. Wait for the removing process to end.
6. Successful removing will be conrmed by the Z-Wave controller’s
message.
TMP
button
NOTE
Adding in security
mode must be per-
formed up to 2 meters
from the controller.
i
NOTE
Removing the device
from the Z-Wave net-
work restores all the
default parameters of
the device (except for
parameter 20).
i
NOTE
In case the device is
not added, please re-
set the device and re-
peat the adding pro-
cedure.
i
TMP
button

7
TEMPERATURE SENSOR
#4: Temperature sensor
CAUTION
Connected the device
in accordance with
the wiring diagram.
Incorrect wiring may
be dangerous or result
in the device break-
down.
!
NOTE
Connecting/discon-
necting the temper-
ature sensor to/from
previously added
Door/Window Sensor,
requires removing
and re-adding the
device to the Z-Wave
network.
i
The DS18B20 temperature sensor may be installed anywhere where
temperature readouts are necessary. If adequately protected, the
DS18B20 sensor may be installed in humid conditions, under water,
sealed in concrete or placed under the oor.
CAUTION
Connecting devic-
es and sensors other
than DS18B20 is not
allowed.
!
To activate the device with temperature measurement functionality:
1. Open the cover.
2. Connect the temperature sensor to terminals of the device
according to the diagram:
3. Add the device (see “Adding/removing the device” on page 6).
4. Install the device (see “Physical installation” on page 9).
GND
max 30m
TD (DQ)
TP (VDQ)
321
(BOTTOM VIEW)
(TOP VIEW)
TMP
DS18B20
123
321
GND
TD (DQ)
TP (VDQ)
DS18B20
+
-
TP
(TEMP_POWER) - power supply terminal of
temperature sensor
TD
(TEMP_DATA) - signal terminal of temperature sensor
GND
(GROUND) - ground terminal

8
BUTTON OR EXTERNAL SENSOR
#5: Button or external sensor
Door/Window Sensor is equipped with a potential-free input. It allows
to change device state using the external button or sensor through
GND signal.
If the Door/Window Sensor will be used only as a binary sensor, do
not install the magnet.
To activate the device as a binary sensor:
1. Open the cover.
2. Connect the button or external sensor to terminals of the device
according to diagram:
3. Add the device (see “Adding/removing the device” on page 6) if
the device is not already added.
4. In case of connecting external sensor modify advanced parameter
no. 20 to match type of the sensor, then remove and re-add the
device to the network.
5. Install the device (see “Physical installation” on page 9).
IN
GND
MOMENTARY SWITCH
(TOP VIEW)
TMP
+
-
GND
(GROUND) - ground terminal
IN
- potential-free input
NOTE
Potential-free input is
a type of input contact
which does not have
a voltage on it after
closing.
i
CAUTION
Connected the device
in accordance with
the wiring diagram.
Incorrect wiring may
be dangerous or result
in the device break-
down.
!

9
PHYSICAL INSTALLATION
#6: Physical installation
To install the Door/Window Sensor:
1. Stick the included self-adhesive pads to the bottom of the device
and magnet.
2. Peel o the protective layer of the sticker.
3. Stick the device onto the door/window frame.
4. Stick the magnet onto the moving part of the door/window, no
further than 5mm from the sensor.
max. 5 mm
Correct postioning of the magnet in relation to the Sensor:
Positioning of the Sensor and the magnet:

10
OPERATING THE DEVICE
#7: Operating the device
Controlling the Door/Window Sensor with FIBARO Home Center
controller:
After adding the Sensor to the FIBARO System, it will be represented
by one or two icons in Home Center interface.
Sensor without connected DS18B20 sensor or used with a button
connected to IN input (without magnet), will be represented by a sin-
gle icon.
In case of connecting DS18B20 temperature sensor, the additional
temperature sensor icon will be displayed.
Tamper (TMP) button:
The Door/Window Sensor is equipped with a tamper switch with two
buttons.
First TMP button is located inside the device, pressed by the closed
cover. Second TMP button is located at bottom of the device, pressed
by the surface on which the device is mounted.
For the tamper switch to work one of the buttons must always be
pressed!
When one of the buttons is released, the tamper alarm will be send to
the controller and associated devices.
Additionally, tamper button allows to control the device directly.
TMP
(TOP VIEW)
(BOTTOM VIEW) TMP
+
-