Fike Fcp-2100ecs User manual

P/N LS10143-002FK-E:B • ECN 00003636

Document LS10143-002FK-E

6/20/2022

Addressable Fire Alarm Control Panel

FCP-2100/FCP-2100ECS

Manual

2FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Fire Alarm & Emergency Communication System Limitations

While a life safety system may lower insurance rates, it is not a substitute for life and property insurance!

An automatic fire alarm system—typically made up of smoke

detectors, heat detectors, manual pull stations, audible warning

devices, and a fire alarm control panel (FACP) with remote

notification capability—can provide early warning of a developing fire.

Such a system, however, does not assure protection against property

damage or loss of life resulting from a fire.

An emergency communication system—typically made up of an

automatic fire alarm system (as described above) and a life safety

communication system that may include an autonomous control unit

(ACU), local operating console (LOC), voice communication, and

other various interoperable communication methods—can broadcast

a mass notification message. Such a system, however, does not

assure protection against property damage or loss of life resulting

from a fire or life safety event.

The Manufacturer recommends that smoke and/or heat detectors be

located throughout a protected premises following the

recommendations of the current edition of the National Fire Protection

Association Standard 72 (NFPA 72), manufacturer's

recommendations, State and local codes, and the recommendations

contained in the Guide for Proper Use of System Smoke Detectors,

which is made available at no charge to all installing dealers. This

document can be found at http://www.systemsensor.com/appguides/.

A study by the Federal Emergency ManagementAgency (an agency

of the United States government) indicated that smoke detectors may

not go off in as many as 35% of all fires. While fire alarm systems are

designed to provide early warning against fire, they do not guarantee

warning or protection against fire. A fire alarm system may not

provide timely or adequate warning, or simply may not function, for a

variety of reasons:

Smoke detectors may not sense fire where smoke cannot reach the

detectors such as in chimneys, in or behind walls, on roofs, or on the

other side of closed doors. Smoke detectors also may not sense a fire

on another level or floor of a building.A second-floor detector, for

example, may not sense a first-floor or basement fire.

Particles of combustion or “smoke” from a developing fire may not

reach the sensing chambers of smoke detectors because:

• Barriers such as closed or partially closed doors, walls, chimneys,

even wet or humid areas may inhibit particle or smoke flow.

• Smoke particles may become “cold,” stratify, and not reach the

ceiling or upper walls where detectors are located.

• Smoke particles may be blown away from detectors by air outlets,

such as air conditioning vents.

• Smoke particles may be drawn into air returns before reaching the

detector.

The amount of “smoke” present may be insufficient to alarm smoke

detectors. Smoke detectors are designed to alarm at various levels of

smoke density. If such density levels are not created by a developing

fire at the location of detectors, the detectors will not go into alarm.

Smoke detectors, even when working properly, have sensing

limitations. Detectors that have photoelectronic sensing chambers

tend to detect smoldering fires better than flaming fires, which have

little visible smoke. Detectors that have ionizing-type sensing

chambers tend to detect fast-flaming fires better than smoldering

fires. Because fires develop in different ways and are often

unpredictable in their growth, neither type of detector is necessarily

best and a given type of detector may not provide adequate warning

of a fire.

Smoke detectors cannot be expected to provide adequate warning of

fires caused by arson, children playing with matches (especially in

bedrooms), smoking in bed, and violent explosions (caused by

escaping gas, improper storage of flammable materials, etc.).

Heat detectors do not sense particles of combustion and alarm only

when heat on their sensors increases at a predetermined rate or

reaches a predetermined level. Rate-of-rise heat detectors may be

subject to reduced sensitivity over time. For this reason, the rate-of-

rise feature of each detector should be tested at least once per year

by a qualifiedfire protection specialist. Heat detectors are designed to

protect property, not life.

IMPORTANT! Smoke detectors must be installed in the same room

as the control panel and in rooms used by the system for the

connection of alarm transmission wiring, communications, signaling,

and/or power. If detectors are not so located, a developing fire may

damage the alarm system, compromising its ability to report a fire.

Audible warning devices such as bells, horns, strobes, speakers

and displays may not alert people if these devices are located on the

other side of closed or partly open doors or are located on another

floor of a building.Any warning device may fail to alert people with a

disability or those who have recently consumed drugs, alcohol, or

medication. Please note that:

• An emergency communication system may take priority over a fire

alarm system in the event of a life safety emergency.

• Voice messaging systems must be designed to meet intelligibility

requirements as defined by NFPA, local codes, and Authorities

Having Jurisdiction (AHJ).

• Language and instructional requirements must be clearly dissemi-

nated on any local displays.

• Strobes can, under certain circumstances, cause seizures in peo-

ple with conditions such as epilepsy.

• Studies have shown that certain people, even when they hear a

fire alarm signal, do not respond to or comprehend the meaning of

the signal.Audible devices, such as horns and bells, can have dif-

ferent tonal patterns and frequencies. It is the property owner's

responsibility to conduct fire drills and other training exercises to

make people aware of fire alarm signals and instruct them on the

proper reaction to alarm signals.

• In rare instances, the sounding of a warning device can cause

temporary or permanent hearing loss.

A life safety system will not operate without any electrical power. If

AC power fails, the system will operate fromstandbybatteriesonly for

a specified time and only if the batteries have been properly

maintained and replaced regularly.

Equipment used in the system may not be technically compatible

with the control panel. It is essential to use only equipment listed for

service with your control panel.

Alarm Signaling Communications:

•IP connections rely on available bandwidth, which could be lim-

ited if the network is shared by multiple users or if ISP policies

impose restrictions on the amount of data transmitted. Service

packages must be carefully chosen to ensure that alarm signals

will always have available bandwidth. Outages by the ISP for

maintenance and upgrades may also inhibit alarm signals. For

added protection, a backup cellular connection is recommended.

•Cellular connections rely on a strong signal. Signal strength can

be adversely affected by the network coverage of the cellular car-

rier, objects and structural barriers at the installation location. Uti-

lize a cellular carrier that has reliable network coverage where the

alarm system is installed. For added protection, utilize an external

antenna to boost the signal.

•Telephone lines needed to transmit alarm signals from a premise

to a central monitoring station may be out of service or temporarily

disabled. For added protection against telephone line failure,

backup alarm signaling connections are recommended.

The most common cause of life safety system malfunction is

inadequate maintenance. To keep the entire life safety system in

excellent working order, ongoing maintenance is required per the

manufacturer's recommendations, and UL and NFPA standards. At a

minimum, the requirements of NFPA 72 shall be followed.

Environments with large amounts of dust, dirt, or high air velocity

require more frequent maintenance. A maintenance agreement

should be arranged through the local manufacturer's representative.

Maintenance should be scheduled as required by National and/or

local fire codes and should be performed by authorized professional

life safety system installers only.Adequate written records of all

inspections should be kept. Limit-F-2020

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 3

Installation Precautions

Adherence to the following will aid in problem-free installation with long-term reliability:

WARNING - Several different sources of power can be con-

nected to the fire alarm control panel. Disconnect all sources of

power before servicing. Control unit and associated equipment may

be damaged by removing and/or inserting cards, modules, or inter-

connecting cables while the unit is energized. Do not attempt to

install, service, or operate this unit until manuals are read and under-

stood.

CAUTION - System Re-acceptance Test after Software Changes:

To ensure proper system operation, this product must be tested in

accordance with NFPA 72 after any programming operation or

change in site-specific software. Re-acceptance testing is required

after any change, addition or deletion of system components, or after

any modification, repair or adjustment to system hardware or wiring.

All components, circuits, system operations, or software functions

known to be affected by a change must be 100% tested. In addition,

to ensure that other operations are not inadvertently affected, at least

10% of initiating devices that are not directly affected by the change,

up to a maximum of 50 devices, must also be tested and proper sys-

tem operation verified.

This system meets NFPArequirements for operation at 0-49º C/32-

120º F and at a relative humidity 93% ± 2% RH (non-condensing) at

32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's

standby batteries and the electronic components may be adversely

affected by extreme temperature ranges and humidity. Therefore, it is

recommended that this system and its peripherals be installed in an

environment with a normal room temperature of 15-27º C/60-80º F.

Verify that wire sizes are adequate for all initiating and indicating

device loops. Most devices cannot tolerate more than a10% I.R. drop

from the specified device voltage.

Like all solid state electronic devices, this system may operate

erratically or can be damaged when subjected to lightning induced

transients. Although no system is completely immune from lightning

transients and interference, proper grounding will reduce susceptibil-

ity. Overhead or outside aerial wiring is not recommended, due to an

increased susceptibility to nearby lightning strikes. Consult with the

Technical Services Department if any problems are anticipated or

encountered.

Disconnect AC power and batteries prior to removing or inserting

circuit boards. Failure to do so can damage circuits.

Remove all electronic assemblies prior to any drilling, filing, ream-

ing, or punching of the enclosure. When possible, make all cable

entries from the sides or rear. Before making modifications, verify that

they will not interfere with battery, transformer, or printed circuit board

location.

Do not tighten screw terminals more than 9 in-lbs. Over-tightening

may damage threads, resulting in reduced terminal contact pressure

and difficulty with screw terminal removal.

This system contains static-sensitive components. Always

ground yourself with a proper wrist strap before handling any circuits

so that static charges are removed from the body. Use static suppres-

sive packaging to protect electronic assemblies removed from the

unit.

Units with a touchscreen display should be cleaned with a dry,

clean, lint free/microfiber cloth. If additional cleaning is required,

apply a small amount of Isopropyl alcohol to the cloth and wipe

clean. Do not use detergents, solvents, or water for cleaning. Do not

spray liquid directly onto the display.

Follow the instructions in the installation, operating, and program-

ming manuals. These instructions must be followed to avoid damage

to the control panel and associated equipment. FACP operation and

reliability depend upon proper installation.

Precau-D2-11-2017

FCC Warning

WARNING: This equipment generates, uses, and can radi-

ate radio frequency energy and if not installed and used in

accordance with the instruction manual may cause interfer-

ence to radio communications. It has been tested and found

to comply with the limits for classA computing devices pur-

suant to Subpart B of Part 15 of FCC Rules, which is

designed to provide reasonable protection against such

interference when devices are operated in a commercial

environment. Operation of this equipment in a residential

area is likely to cause interference, in which case the user

will be required to correct the interference at his or her own

expense.

Canadian Requirements

This digital apparatus does not exceed the Class A limits for

radiation noise emissions from digital apparatus set out in

the Radio Interference Regulations of the Canadian Depart-

ment of Communications.

Le present appareil numerique n'emet pas de bruits radio-

electriques depassant les limites applicables aux appareils

numeriques de la classeAprescrites dans le Reglement sur

le brouillage radioelectrique edicte par le ministere des

Communications du Canada.

Flexput®, Honeywell®, JumpStart®, and SWIFT® are registered trademarks of Honeywell International Inc.Microsoft® and Windows® are registered trademarks of the

Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered trademark of The Mozilla Foundation.

4FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Software Downloads

In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent

upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly

recommend that you download the most current version of software for each product prior to commissioning any system. Contact

Technical Support with any questions about software and the appropriate version for a specific application.

Documentation Feedback

Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions about our online

Help or printed manuals, you can email us.

Please include the following information:

• Product name and version number (if applicable)

• Printed manual or online Help

• Topic Title (for online Help)

• Page number (for printed manual)

• Brief description of content you think should be improved or corrected

• Your suggestion for how to correct/improve documentation

Send email messages to:

[email protected]

or call (800)979-3453, x21 in US or (816)229-3405 international

This symbol (shown left) on the product(s) and / or accompanying documents means that used electrical and electronic products

should not be mixed with general household waste. For proper treatment, recovery and recycling, contact your local authorities or

dealer and ask for the correct method of disposal.

Electrical and electronic equipment contains materials, parts and substances, which can be dangerous to the environment and harmful

to human health if the waste of electrical and electronic equipment (WEEE) is not disposed of correctly.

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 5

Table of Contents

Section 1: Introduction ................................................................................................................................................... 10

1.1: Basic System Overview...................................................................................................................................................................................10

1.1.1: Hardware Features................................................................................................................................................................................10

1.1.2: Network System Hardware Features ....................................................................................................................................................10

1.1.3: Software Features .................................................................................................................................................................................10

1.1.4: FCP-2100ECS Features........................................................................................................................................................................11

1.2: Terms Used in this Manual..............................................................................................................................................................................11

1.3: Compatible Products........................................................................................................................................................................................12

1.4: Related Documentation ...................................................................................................................................................................................13

Section 2: Agency Listings, Approvals, and Requirements........................................................................................ 14

2.1: Federal Communications Commission (FCC).................................................................................................................................................14

2.2: Underwriters Laboratories (UL)......................................................................................................................................................................15

2.2.1: Requirements for All Installations........................................................................................................................................................15

2.2.2: UL 864 9th and 10th Edition ................................................................................................................................................................15

2.2.3: Requirements for Central Station Fire Alarm Systems ........................................................................................................................15

2.2.4: Requirements for Local Protected Fire Alarm Systems .......................................................................................................................15

2.2.5: Requirements for Remote Station Protected Fire Alarm Systems........................................................................................................15

2.2.6: Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 720..................................15

2.2.7: NFPA Requirements.............................................................................................................................................................................16

Section 3: Before You Begin Installation ...................................................................................................................... 18

3.1: Inventory..........................................................................................................................................................................................................18

3.2: Environmental Specifications..........................................................................................................................................................................18

3.3: Software Downloads........................................................................................................................................................................................18

3.4: Electrical Specifications ..................................................................................................................................................................................18

3.5: Calculating Current Draw and Standby Battery ..............................................................................................................................................20

3.5.1: Current Draw Worksheet Requirements...............................................................................................................................................20

3.5.2: Current Draw Worksheet for Fike SLC Devices..................................................................................................................................20

3.5.3: Maximum Battery Standby Load..........................................................................................................................................................24

Section 4: Control Panel Installation............................................................................................................................. 25

4.1: Mounting the Control Panel Cabinet...............................................................................................................................................................25

4.1.1: Preventing Water Damage....................................................................................................................................................................25

4.1.2: Removing the FCP-2100 Assembly from the Housing........................................................................................................................25

4.1.3: Ethernet Connection .............................................................................................................................................................................25

4.2: Board Assembly Diagram................................................................................................................................................................................26

4.3: Wiring Specifications.......................................................................................................................................................................................27

4.4: AC Power Connection .....................................................................................................................................................................................28

4.5: Battery Power ..................................................................................................................................................................................................29

4.5.1: Battery Accessory Cabinets..................................................................................................................................................................29

4.6: SBUS Wiring ...................................................................................................................................................................................................31

4.6.1: Calculating Wiring Distance for SBUS Modules.................................................................................................................................31

4.6.2: Wiring Configurations..........................................................................................................................................................................33

4.7: FIK-RA100 Remote Annunciator Installation.................................................................................................................................................33

4.7.1: Mounting the FIK-RA100 ....................................................................................................................................................................34

4.7.2: FIK-RA100 Connection to the Panel....................................................................................................................................................36

4.8: FIK-RA1000R Remote Annunciator Installation............................................................................................................................................36

4.8.1: Mounting the FIK-RA1000R................................................................................................................................................................36

4.9: FIK-RA2000 Remote Annunciator Installation...............................................................................................................................................39

4.9.1: Mounting the FIK-RA2000 ..................................................................................................................................................................40

4.9.2: FIK-RA2000 Connection to the Panel..................................................................................................................................................41

4.10: Temporary Programming Display .................................................................................................................................................................41

4.11: FIK-6815 Installation.....................................................................................................................................................................................41

4.11.1: FIK-6815 Connection to the Panel .....................................................................................................................................................42

4.12: FIK-5824 Serial/Parallel Interface Module Installation ................................................................................................................................42

4.12.1: Selecting FIK-5824 Options...............................................................................................................................................................43

4.13: FIK-5880 LED I/O Module...........................................................................................................................................................................43

4.13.1: FIK-5880 Board Layout .....................................................................................................................................................................44

4.13.2: FACP Connection...............................................................................................................................................................................44

4.13.3: LED Wiring ........................................................................................................................................................................................44

4.13.4: Dry Contact Wiring ............................................................................................................................................................................45

6FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Table of Contents

4.14: FIK-5865-3 / FIK-5865-4 LED Annunciator Installation .............................................................................................................................45

4.14.1: FACP Connection...............................................................................................................................................................................46

4.14.2: FIK-5865 Mounting............................................................................................................................................................................47

4.15: Configuring SBUS Modules..........................................................................................................................................................................47

4.15.1: Assigning SBUS Module IDs.............................................................................................................................................................47

4.15.2: SBUS Bandwidth Considerations.......................................................................................................................................................48

4.16: Telephone Connection ...................................................................................................................................................................................48

4.17: Flexput I/O Circuits.......................................................................................................................................................................................49

4.17.1: Conventional Notification Appliance.................................................................................................................................................49

4.17.2: Conventional Input Switch Circuits....................................................................................................................................................50

4.17.3: Installing 2-Wire Smoke Detectors ....................................................................................................................................................51

4.17.4: Installing 4-Wire Smoke Detectors ....................................................................................................................................................52

4.17.5: Auxiliary Power Installation...............................................................................................................................................................53

4.18: Onboard Relays (Conventional) ....................................................................................................................................................................54

4.18.1: Trouble Relay .....................................................................................................................................................................................54

4.18.2: Programmable Relays.........................................................................................................................................................................54

4.19: Remote Station Applications .........................................................................................................................................................................54

4.19.1: Keltron Model 3158 Installation.........................................................................................................................................................54

4.19.2: City Box Connection Using the 5220 Module ...................................................................................................................................55

4.19.3: Using the Addressable Relay Module for City Box Connection........................................................................................................56

4.19.4: NFPA 72 Polarity Reversal ................................................................................................................................................................56

4.19.5: Transmitter Activated by Dry Contacts..............................................................................................................................................57

Section 5: Networking..................................................................................................................................................... 58

5.1: Network System Hardware Features ...............................................................................................................................................................58

5.1.1: Networked Sites....................................................................................................................................................................................58

5.1.2: Wiring Options to Connect Networked Panels.....................................................................................................................................58

5.2: Model RFCP-2100...........................................................................................................................................................................................58

5.3: Network Wiring ...............................................................................................................................................................................................58

5.4: FIK-NIC Wiring Options.................................................................................................................................................................................59

5.4.1: Fiber Loop Modules .............................................................................................................................................................................59

5.4.2: FIK-NIC Installation.............................................................................................................................................................................60

5.4.3: FIK-NIC Remote Mounting .................................................................................................................................................................61

5.4.4: Wiring...................................................................................................................................................................................................61

5.5: Setting the Network ID for Each Panel ...........................................................................................................................................................63

Section 6: Network Management................................................................................................................................... 64

6.1: Network Diagnostics .......................................................................................................................................................................................64

6.1.1: Ping Panel.............................................................................................................................................................................................64

6.1.2: Data Network Status.............................................................................................................................................................................64

6.1.3: Voice Network Status...........................................................................................................................................................................64

6.2: Network Programming ....................................................................................................................................................................................64

6.2.1: Learn Network......................................................................................................................................................................................64

6.2.2: Edit Network Names.............................................................................................................................................................................64

6.2.3: Edit Panel ID.........................................................................................................................................................................................65

6.2.4: Computer Access..................................................................................................................................................................................65

6.2.5: Access Codes........................................................................................................................................................................................65

6.2.6: Communicator Options.........................................................................................................................................................................65

6.3: Voice Options...................................................................................................................................................................................................67

6.3.1: Edit Timers ...........................................................................................................................................................................................67

6.3.2: Edit Voice Commands..........................................................................................................................................................................67

6.4: Sync Network Options.....................................................................................................................................................................................68

6.5: Network Management Quick Reference .........................................................................................................................................................69

Section 7: Programming Overview................................................................................................................................ 71

7.1: JumpStart Auto-Programming.........................................................................................................................................................................71

7.1.1: Input Points...........................................................................................................................................................................................71

7.1.2: Output Points ........................................................................................................................................................................................71

7.1.3: Running JumpStart Auto-Programming...............................................................................................................................................71

7.2: Mapping Overview ..........................................................................................................................................................................................72

7.2.1: Input Point Mapping.............................................................................................................................................................................73

7.2.2: Output Circuit Mapping........................................................................................................................................................................73

7.2.3: Event Mapping.....................................................................................................................................................................................74

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 7

Table of Contents

7.2.4: Mapping LED Points............................................................................................................................................................................76

7.2.5: Mapping LED Points for a Networked System....................................................................................................................................76

7.3: Programming Using the HFSS Software Suite................................................................................................................................................76

7.4: Programming Using an Annunciator ...............................................................................................................................................................77

7.4.1: Entering / Exiting Panel Programming.................................................................................................................................................77

7.5: Programming Menu Quick Reference.............................................................................................................................................................78

Section 8: Programming................................................................................................................................................. 88

8.1: UL 864 / UL 2572 Programming Requirements..............................................................................................................................................88

8.2: Modules ...........................................................................................................................................................................................................88

8.2.1: Edit Modules.........................................................................................................................................................................................88

8.2.2: Adding a Module..................................................................................................................................................................................89

8.2.3: Deleting a Module ................................................................................................................................................................................89

8.2.4: View Module List.................................................................................................................................................................................89

8.3: Zone.................................................................................................................................................................................................................90

8.3.1: Edit Zone ..............................................................................................................................................................................................90

8.3.2: View Zone Points .................................................................................................................................................................................92

8.4: Group...............................................................................................................................................................................................................92

8.4.1: Edit Group ............................................................................................................................................................................................92

8.4.2: View Group Points ...............................................................................................................................................................................93

8.4.3: Edit OPG Template...............................................................................................................................................................................93

8.5: Point.................................................................................................................................................................................................................94

8.5.1: Point Programming For FIK-6815 Module..........................................................................................................................................94

8.5.2: Point Programming For Internal or External Power Module (FIK-RPS1000).....................................................................................97

8.5.3: Point Programming for FIK-5880/FIK-5865 Modules.........................................................................................................................98

8.5.4: Point Programming for the FIK-5496...................................................................................................................................................99

8.5.5: Point Programming for ECS Amplifiers...............................................................................................................................................99

8.5.6: Point Programming for FIK-NVCM and FIK-RVM............................................................................................................................99

8.6: System Options..............................................................................................................................................................................................101

8.6.1: Communication Options.....................................................................................................................................................................101

8.6.2: Daytime/Nighttime Sensitivity...........................................................................................................................................................104

8.6.3: Holiday Days ......................................................................................................................................................................................104

8.6.4: Time Options ......................................................................................................................................................................................104

8.6.5: Miscellaneous Options........................................................................................................................................................................105

8.6.6: Daylight Saving Options.....................................................................................................................................................................106

8.6.7: Edit Banner.........................................................................................................................................................................................106

8.6.8: SLC Family.........................................................................................................................................................................................106

8.6.9: JumpStart Auto-Programming............................................................................................................................................................106

8.7: Restore Defaults.............................................................................................................................................................................................107

8.8: Voice Options.................................................................................................................................................................................................107

8.8.1: VCM Maintenance..............................................................................................................................................................................107

8.8.2: Voice Settings.....................................................................................................................................................................................107

Section 9: System Operation........................................................................................................................................ 108

9.1: Annunciator Description................................................................................................................................................................................108

9.1.1: LCD Display.......................................................................................................................................................................................108

9.1.2: Banner.................................................................................................................................................................................................108

9.2: Menu System ................................................................................................................................................................................................109

9.2.1: Panel Login Menu...............................................................................................................................................................................109

9.2.2: Main Menu Overview.........................................................................................................................................................................110

9.2.3: Using the Menus.................................................................................................................................................................................111

9.3: Basic Operation .............................................................................................................................................................................................111

9.3.1: Setting Time and Date ........................................................................................................................................................................111

9.3.2: Disable / Enable a Point......................................................................................................................................................................111

9.3.3: View Event History ............................................................................................................................................................................111

9.3.4: Conduct a Fire Drill............................................................................................................................................................................112

9.3.5: Conduct an Indicator Test...................................................................................................................................................................112

9.3.6: Conduct a Walk Test ..........................................................................................................................................................................112

9.3.7: Conduct a Communicator Test...........................................................................................................................................................112

9.3.8: Manual AlarmNet Registration...........................................................................................................................................................112

9.3.9: Silence Alarms or Troubles................................................................................................................................................................113

9.3.10: Reset Alarms.....................................................................................................................................................................................113

9.3.11: Check Detector Sensitivity Through Point Status...........................................................................................................................113

8FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Table of Contents

9.3.12: View Status of a Point ......................................................................................................................................................................114

9.3.13: View Alarms or Troubles .................................................................................................................................................................114

9.3.14: System Information .........................................................................................................................................................................114

9.4: Event Priority.................................................................................................................................................................................................115

9.4.1: System Control ...................................................................................................................................................................................115

9.4.2: System Override .................................................................................................................................................................................115

9.4.3: Event Priority......................................................................................................................................................................................115

9.4.4: Priority Rules......................................................................................................................................................................................116

9.4.5: Other Priority Considerations.............................................................................................................................................................116

9.5: Operation Mode Behavior .............................................................................................................................................................................116

9.5.1: Multi-Site Annunciator and Multi-Site User Access..........................................................................................................................119

9.6: Releasing Operations.....................................................................................................................................................................................119

9.6.1: Single Interlock Zone Releasing.........................................................................................................................................................120

9.6.2: Double Interlock Zone Releasing.......................................................................................................................................................120

9.7: Smoke Alarm Verification .............................................................................................................................................................................121

9.8: Function Keys...............................................................................................................................................................................................121

9.8.1: Recording an F-Key Macro ................................................................................................................................................................121

9.8.2: Aborting an F-Key Macro Recording Session....................................................................................................................................121

9.8.3: Erasing an F-Key Macro.....................................................................................................................................................................121

9.8.4: Using a Recorded F-Key Macro.........................................................................................................................................................122

9.8.5: F-Key Status Event.............................................................................................................................................................................122

9.8.6: F-Key Map Inhibit..............................................................................................................................................................................122

Section 10: Emergency Communication System Operation..................................................................................... 123

10.1: Overview......................................................................................................................................................................................................123

10.2: LOC Functionality.......................................................................................................................................................................................123

10.2.1: Keys and LEDs.................................................................................................................................................................................123

10.2.2: Gaining ECS Control........................................................................................................................................................................124

10.2.3: Manual ECS......................................................................................................................................................................................125

10.2.4: Fire Page Mode.................................................................................................................................................................................125

10.2.5: Message Mode..................................................................................................................................................................................125

10.2.6: Custom ECS Event ...........................................................................................................................................................................126

10.2.7: Passing ECS Control.........................................................................................................................................................................126

10.2.8: Exit ECS Control Menu....................................................................................................................................................................126

10.2.9: Relinquish ECS Control ...................................................................................................................................................................127

10.2.10: ECS Reset .......................................................................................................................................................................................127

10.3: ECS Super User ...........................................................................................................................................................................................127

10.4: ECS Point Functionality ..............................................................................................................................................................................127

10.4.1: ECS Point Activations......................................................................................................................................................................127

10.4.2: FIK-NVCM and FIK-RVM Points...................................................................................................................................................127

10.5: Amplifier Programming...............................................................................................................................................................................127

10.5.1: Adding an Amplifier.........................................................................................................................................................................127

10.5.2: Editing an Amplifier.........................................................................................................................................................................128

10.6: LOC Programming ......................................................................................................................................................................................128

10.6.1: Adding an LOC.................................................................................................................................................................................128

10.6.2: Editing an LOC.................................................................................................................................................................................128

10.7: Using the Microphone .................................................................................................................................................................................129

10.7.1: Microphone Functionality ................................................................................................................................................................129

10.7.2: Custom ECS Event ...........................................................................................................................................................................129

10.7.3: Fire Page...........................................................................................................................................................................................129

10.7.4: Emergency Page ...............................................................................................................................................................................129

10.7.5: Paging ...............................................................................................................................................................................................129

10.8: Recording Custom Messages.......................................................................................................................................................................130

10.8.1: Recording Messages 1-15 Using Aux Audio Input..........................................................................................................................130

10.8.2: Recording Messages 1-15 Using the Microphone............................................................................................................................131

10.8.3: Erasing User Message.......................................................................................................................................................................132

10.8.4: Using HFSS Voice Message Load Software....................................................................................................................................132

10.9: Network Paging ...........................................................................................................................................................................................133

10.9.1: Priority..............................................................................................................................................................................................133

10.9.2: Configuration....................................................................................................................................................................................133

Section 11: Reporting ................................................................................................................................................... 134

11.1: Receivers Compatible with the Control Panel.............................................................................................................................................134

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 9

Table of Contents

11.2: SIA - Panel PI Modifier Reporting ..............................................................................................................................................................143

11.3: SIA – Panel Communicator .........................................................................................................................................................................144

Section 12: Testing and Troubleshooting................................................................................................................... 145

12.1: Troubleshooting...........................................................................................................................................................................................145

12.1.1: Common Problems ...........................................................................................................................................................................145

12.2: Periodic Testing and Maintenance...............................................................................................................................................................145

12.3: Event History...............................................................................................................................................................................................146

12.4: Built-in Troubleshooting and Testing Tools ................................................................................................................................................146

12.4.1: SLC Device Locater .........................................................................................................................................................................146

12.4.2: SLC Multiple Device Locater...........................................................................................................................................................146

12.4.3: I/O Point Control ..............................................................................................................................................................................147

12.4.4: Earth Fault Resistance ......................................................................................................................................................................147

Section 13: Installation Records.................................................................................................................................. 149

13.1: Detector and Module Point Record .............................................................................................................................................................149

13.2: Additional SLC Devices ..............................................................................................................................................................................151

13.3: Conventional Output Point Record..............................................................................................................................................................152

Appendix A: Editing Text Using the Built-In Programmer......................................................................................... 153

A.1: Characters Used for Editing Text..................................................................................................................................................................153

A.2: Example Name Edit......................................................................................................................................................................................153

Appendix B: Expanded Receiver/Panel Relationship................................................................................................ 154

Appendix C: Cadence Patterns.................................................................................................................................... 155

Appendix D: Panel Security.......................................................................................................................................... 156

Model FCP-2100 Basic Operating Instructions........................................................................................................... 157

Model FCP-2100ECS Basic Operating Instructions................................................................................................... 159

Keypad and LED Indicators.......................................................................................................................................... 161

ECS Control ................................................................................................................................................................... 163

10 FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Section 1: Introduction

The FCP-2100, FCP-2100HV, FCP-2100ECS, and FCP-2100ECSHV are analog addressable fire alarm control panels (FACP), that meets

the requirements of UL 864. The FCP-2100ECS and FCP-2100ECSHVanalog addressable fire control system combined with an Emergency

Communication System that meet the requirements for Mass Notification as described in UL 864 and UL 2572.

The RFCP-2100 is the same as the FCP-2100 without the display. The RFCP-2100 is used in a networked system where there is at least one

FCP-2100 in the system. When using the RFCP-2100 as a standalone local unit, one LCD annunciator must be connected and the annuncia-

tor must be wired in conduit within 20’of the RFCP-2100.

1.1 Basic System Overview

The FCP-2100 base system is packaged as an assembled stack of 3 circuit boards mounted to an aluminum housing.

1.1.1 Hardware Features

• The basic FCP-2100 panel contains one built-in signaling line circuit (SLC), which supports up to 159 sensors and 159 modules.

Additional SLC loops can be added to increase overall point capacity.

• Additional FIK-6815 SLC expanders supports 159 sensors and 159 modules for a maximum of 2,100 points per FCP-2100 control

panel.

• 9.0A of output power is available through 8 sets of terminals for notification and auxiliary applications. Each circuit is power limited

per UL 864 and can source up to 3.0A (total output power must not exceed 9.0A). The constant auxiliary power load must not exceed

6.0A for normal standby.

• Built-in dual phone line, digital alarm communicator/transmitter (DACT), or IP technologies

• Reports events to central station by point or by zone

• UL-Listed for pre-action and deluge releasing systems

• Dedicated Form C trouble relay and two general purpose Form C programmable relays

• Can be used with up to 31 FIK-RA2000, FIK-RA1000R, or FIK-RA100 remote annunciators in any combination

• Supports the FIK-5865-3, FIK-5865-4, and FIK-5880 LED annunciators1. See Section 4.13 and Section 4.14 for additional information

on these models.

• Printing of event log available through the FIK-58241serial/parallel printer interface module

• Supports conventional 2-wire & 4-wire detectors using the 8 Flexput circuits or SLC zone modules

• Add four notification/auxiliary power circuits with each FIK-5496 Intelligent Power Module

• Add six Flexput circuits with each FIK-RPS1000 Remote Power Supply

1. The system supports a maximum of 63 SBUS devices in any combination.

1.1.2 Network System Hardware Features

• The default network setup can contain up to 32- FCP-2100 panels connected.

• Network support for up to 32 sites

• Each building is referred to as a “site”.

• Panels can be interconnected using CLASS B or CLASS A topology.

• Use the FIK-NIC network card to network panels together. Copper wire or fiber-optic cable panel connectivity can be used within the

same networked system.

• The network architecture provides true peer to peer capability allowing network survivability for all hardware that remains operational

in the event of partial system failure.

1.1.3 Software Features

• 999 software zones, 999 output groups

• Advanced analog smoke detector features:

– Three sensitivity settings (high, medium, low)

– Automatic drift compensation

– Maintenance alert region

– Point status meets calibrated smoke test requirements for NFPA 72

– Automatic day/night sensitivity adjustment

• “JumpStart AutoProgramming” feature for easy programming

• Non-volatile event history stores 1000 events per panel

• A choice of output patterns available for notification outputs, includingANSI 3.41 temporal signal

• Built-in synchronization appliance support for AMSECO®, Gentex®, System Sensor®, and Wheelock®

NOTE: All references to the FCP-2100 within this manual are applicable to the FCP-2100, FCP-2100HV, FCP-2100ECS, FCP-2100ECSHV,

RFCP-2100, and RFCP-2100HV unless otherwise indicated.

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 11

Terms Used in this Manual Introduction

1.1.4 FCP-2100ECS Features

• 15 recordable, one-minute messages that can be mapped to eight ECS buttons

• ECS messages can be selected as priority over fire

• Support of up to 15 FIK-LOC2100 Local Operator Consoles

• Programmable trigger inputs from an external source, such as a Monaco system, to either the FIK-NVCM, FIK-RVM, FIK-5880, any

SLC input module, or Flexput module

• Support for up to 16 SBUS addressable amplifiers using a combination of FIK-50W, FIK-125W, FIK-INT50W, or FIK-DUAL50W for

a maximum of 2,000 watts per system and up to 128 mappable speaker circuits

• Support for dual channel and backup audio using the FIK-DUAL50W amplifier and FIK-50WBU back-up amplifier

• Single enclosure for both Fire and Emergency Control System components

• Support for one FIK-NVCM

• Onboard supervised microphone

1.2 Terms Used in this Manual

The following terminology is used with the above mentioned control panels:

Term Description

SLC Signaling line circuit

Module The term module is used for all hardware devices except for SLC addressable devices and notification appliances.

This includes the FCP-2100 panel itself and the built-in power supply. It also refers to any (optional) FIK-6815 SLC

expansion modules.

Input Point An addressable sensing device, such as a smoke or heat detector or a contact monitor device

Input Zone A protected area made up of input points

Output Point (or “Output Circuit”) A notification point or circuit for notification appliances. Relay circuits and auxiliary power circuits are also

considered output points

Group (“Output Group” or OPG) A group of output points. Operating characteristics are common to all output points in a group.

Output (or “Cadence”) Pattern The pattern that the output will use, for example, Constant, March Code, ANSI 3.41. Applies to zones and special

system events. See Appendix B for additional information.

Mapping Mapping is the process of specifying which outputs are activated when certain events occur in the system.

Section 7.2 explains mapping in detail.

Networking Up to 32 panels can be networked.

Network System Consist of any combination of 32 panels of these model numbers: FCP-75, FCP-300, FCP-300ECS,FCP-2100,

FCP-2100ECS, and RFCP-2100

ECS Emergency Communication System

SWIFT Smart Wireless Integrated Fire Technology

12 FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Introduction Compatible Products

1.3 Compatible Products

Table 1.1 lists the products available for use with the FCP-2100.

Type of Device Model Description

Addressable SLC Devices Refer to the Device Compatibility Document and SLC Wiring Manual for a list of compatible devices.

SWIFT Wireless SLC Devices Refer to the SWIFT Wireless Manual for a list of compatible devices.

Other Modules FIK-5824 Serial/Parallel

Printer Interface Module Allows a printer to be attached for the system for on-site logging. Four maximum

per system.

FIK-6815 SLC EXPANDER Each FIK-6815 supports up to 159 sensors and 159 modules. The maximum point

count for Fike IDP devices is limited to 2,100 per panel. The FIK-6815 supports

System Sensor devices only.

RFCP-2100 Remote Fire

Panel without display Same operation as FCP-2100 without display

FIK-RPS1000 Intelligent

Power Module Provides additional power, six Flexput circuits, and two Form C relays.

FIK-5496 NAC Expander Provides four additional Notification Appliance Circuits/Auxiliary power.

FIK-RA2000 LCD Alarm

Annunciator 4x40 LCD annunciator. Same operation, similar appearance as onboard

annunciator.Any combination of supported annunciators for a max of 63.

FIK-RA1000R LCD Alarm

Annunciator 4x20 LCD annunciator. Any combination of supported annunciators for a max of

31.

FIK-RA100 LCD Alarm

Annunciator 4x20 LCD annunciator. Any combination of supported annunciators for a max of

31.

5860TR Trim Ring Kits for

FIK-RA1000R Trim ring kit for surface mounting the 5860 annunciator.

FIK-5865-3and FIK-5865-4

LED Annunciators LED annunciator can display up to 30 LEDs (15 red and 15 yellow). FIK-5865-4

has key switches for silence and reset, and a system trouble LED.

FIK-5880 LED I/O Module Driver for up to 40 LEDs. Interfaces with customized annunciator boards. In

addition, the FIK-5880 has eight generic switch input points.

FIK-5883 General Purpose

Relay Module Provides 10 Form C relays. Designed to be driven by the FIK-5880. Up to four FIK-

5883s can be used with each FIK-5880 module.

Audio Devices

(for FCP-2100ECS only) FIK-SW24 24 Switch expander Refer to the FikeECS Series

Installation Manual PN

LS10262-001FK-E for more

info on these accessories.

FIK-NVCM Network Voice Control Module

FIK-50W 50 watt audio amplifier

FIK-125W 125 watt audio amplifier

FIK-INT50W 50 watt internal amplifier

FIK-DUAL50W Dual Channel amplifier

FIK-50WBU Backup daughter card

FIK-CE4 Provides 4 additional audio circuits for the FIK-

50W or the FIK-125W

FIK-RVM Remote Voice Microphone

FIK-LOC2100 Local Operating Console

Networking FIK-NIC Network Interface Card Refer to LS10172-002FK-E

FIK-FML Fiber-Optic Multi Mode, Receiver Refer to LS10178-002FK-E

FIK-FSL Fiber-Optic Single Mode, Transmitter

Wireless FIK-W-WGI Wireless Gateway Refer to the SWIFT wireless

Installation Manual P/N

LS10036-000FK-E for more

information on these

accessories.

FIK-W--PHOTO Wireless Photoelectric Smoke Detector

FIK-W-ACCLIMATE Wireless Multi criteria photoelectric smoke

detector with thermal (135°F)

FIK-W-HEAT-ROR Wireless Heat Rate of Rise Heat Detector

FIK-W-HEAT Wireless 135° fixed Heat Detector

FIK-W-MONITOR Wireless Addressable Monitor module

FIK-W-RELAY Wireless Addressable Relay module

B210W 6" wireless base

Table 1.1 FCP-2100 Compatible Products

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 13

Related Documentation Introduction

1.4 Related Documentation

Refer to the following documents for more information.

Miscellaneous 7860 Telephone Cord RJ31X cord for connecting phone line to the FCP-2100

HFSS Software Suite For communication and panel programming with a Windows-based computer.

Enables remote viewing of detector status and event history.

RBB Remote Battery Box for mounting backup batteries up to 35AH that are too large to

fit into the main control panel cabinet. Dimensions: 16" W x 10" H x 6" D (40.64 cm

W x 25.4 cm H x 15.24 cm D)

RBB Remote Battery Box for mounting backup batteries that are too large to fit into the

main control panel cabinet. Dimensions: 16" W x 10" H x 6" D

(40.64 cm W x 25.4 cm H x 15.24 cm D).

Type of Device Model Description

Table 1.1 FCP-2100 Compatible Products (Continued)

Title Document Number

SLC Wiring Manual LS10179-000FK-E

Device Compatibility Document LS10167-005FK-E

FIK-5824 Printer Interface Module Install Sheet LS10254-002FK-E

FIK-RPS1000 Power Supply Manual LS10259-001FK-E

FIK-5496 NAC Expander Manual LS10253-001FK-E

FIK-RA100 Annunciator Install Sheet LS10260-001FK-E

FIK-RA1000R LCD Annunciator Install Sheet LS10258-001FK-E

FIK-RA2000 LCD Annunciator LS10261-001FK-E

FIK-5865-3 and FIK-5865-4 LED Annunciator LS10255-001FK-E

FIK-5880 LED Driver Module LS10256-001FK-E

FIK-5883 General Purpose Relay Module LS10257-001FK-E

Fike ECS Series Manual LS10262-001FK-E

FIK-RVM Install Sheet LS10311-001FK-E

FIK-SW24 Install Sheet LS10264-001FK-E

FIK-CE4 Install Sheet LS10263-001FK-E

FIK-INT50W Install Sheet LS10119-002FK-E

FIK-RPU Install Sheet LS10152-002FK-E

FIK-NVCM Install Sheet LS10169-002FK-E

FIK-LOC Install Sheet LS10187-002FK-E

FIK-LOC2100 Install Sheet LS10188-002FK-E

FIK-EMG Install Sheet LS10191-002FK-E

FIK-NIC Install Sheet LS10172-002FK-E

FIK-FML/FSL Install Sheet LS10178-002FK-E

MRD-1 Releasing Disconnect LS10231-000GE-E

Table 1.2 Related Documentation

14 FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Section 2: Agency Listings, Approvals, and Requirements

2.1 Federal Communications Commission (FCC)

The following information must be provided to the telephone company before the FCP-2100 can be connected to the phone lines:

This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the inside cover of this equipment is a

label that contains, among other information, a product identifier. If requested, this information must be provided to the telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68

rules and requirements adopted by the ACTA. A compliant telephone cord (not provided) and modular jack must be utilized with this prod-

uct. It is designed to be used with a modular jack that is also compliant.

The REN (ringer equivalence number) provided on this installation sheet is used to determine the number of devices that may be connected

to the public switched telephone network. This number must not exceed 5.0. Since this product has an REN of 1.0A, the number of devices

is limited. The REN number is embedded in the FCC registration number as 10A.

If the FCP-2100 causes harm to the telephone network, the telephone company will notify you in advance that the temporarily discontinu-

ance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible.

Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equip-

ment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain unin-

terrupted service.

If trouble is experienced with the FCP-2100, for repair or warranty information, contactFike at (800)979-3453 or www.fike.com. If the

equipment is causing harm to the telephone network, the telephone company may request that you disconnect the FCP-2100 until the prob-

lem has been resolved.

This product cannot be adjusted or repaired in the field. It must be returned to the factory for service.

This equipment is not designed for use with party line service. Connection to party line service is subject to state tariffs.You may contact the

state public utility commission, public service commission or corporation commission for information.

Since the FCP-2100 is a commercial fire alarm panel, it must be connected upstream of all other equipment utilizing the phone lines. If you

have questions about the installation, contact your telephone company or a qualified installer.

Manufacturer: Fike

Model Number: FCP-2100/ECS

FCC registration number: US: HS9AL10A2100

Ringer equivalence: 1.0A

Type of jack: RJ31X

Facility Interface Codes: Loop Start: 02LS2

Service Order Code: 9.0F

WARNING: FCC PART 15

THIS DEVICE HAS BEEN VERIFIED TO COMPLY WITH FCC RULES PART 15. OPERATION IS SUBJECT TO THE

FOLLOWING CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE RADIO INTERFERENCE,AND (2) THIS DEVICE MUST

ACCEPTANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

CAUTION: INSTALLATION AND TEST

TO ENSURE PROPER OPERATION, THIS EQUIPMENT MUST BE INSTALLED ACCORDING TO THE ENCLOSED

INSTALLATION INSTRUCTIONS. TO VERIFY THAT THE EQUIPMENT IS OPERATING PROPERLY AND CAN

SUCCESSFULLY REPORTAN ALARM, THIS EQUIPMENT MUST BE TESTED IMMEDIATELY AFTER INSTALLATION,

AND PERIODICALLY THEREAFTER, ACCORDING TO THE ENCLOSED TEST INSTRUCTIONS.

CAUTION: LINE IN USE

IN ORDER FOR “ALARM DIALING EQUIPMENT” TO BE ABLE TO SEIZE THE PHONE LINE TO REPORTAN ALARM OR

OTHER EVENT WHEN OTHER CUSTOMER EQUIPMENT (TELEPHONE, ANSWERING SYSTEM, COMPUTER MODEM,

ETC.) CONNECTED TO THE SAME LINE IS IN USE, “ALARM DIALING EQUIPMENT” MUST BE CONNECTED TOA

PROPERLY INSTALLED RJ31X JACK. THE RJ31X JACK MUST BE CONNECTED IN SERIES WITH, AND AHEAD OF, ALL

OTHER EQUIPMENTATTACHED TO THE SAME PHONE LINE. SERIES INSTALLATION OF AN RJ31X JACK IS DEPICTED

IN THE FIGURE BELOW. IF YOU HAVE ANY QUESTIONS CONCERNING THESE INSTRUCTIONS, CONSULT YOUR

TELEPHONE COMPANY OR A QUALIFIED INSTALLER ABOUT INSTALLING THE NECESSARY JACKAND ALARM

DIALING EQUIPMENT.

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 15

Underwriters Laboratories (UL) Agency Listings, Approvals, and Requirements

2.2 Underwriters Laboratories (UL)

2.2.1 Requirements for All Installations

General requirements are described in this section. When installing an individual device, refer to the specific section of the manual for addi-

tional requirements. The following subsections list specific requirements for each type of installation (for example, Central Station Fire

Alarm systems, Local Protected Fire Alarm systems, and so on). See Section 9.6 for information on releasing operation.

1. All field wiring must be installed in accordance with NFPA 70 National Electric Code.

2. Use the addressable smoke detectors specified in the SLC Wiring Manual and/or conventional detectors listed in the Device

Compatibility Document.

3. Use UL listed notification appliances compatible with the FCP-2100 from those specified in the Device Compatibility Document.

4. Afull system checkout must be performed any time the panel is programmed.

Restricted Options:

• The loss of AC signal is defaulted to 3 hours, but the system still allows settings from 0 - 30 hours. For UL certified installations, this

number must be set from 1 to 3 hours.

• The system allows the use of non-latching, spot type smoke detectors. This feature may not be used in commercial applications

whereby a general alarm is sounded. It is intended for elevator recall, door holding applications, and hotel/motel room applications.

• The system allows the Alarm Verification confirmation time to be set from 60 to 250 seconds. For UL certified installations the setting

must be a minimum of 60 seconds.

• The systems allows the Auto-resound time to be set to 24 or 4 hours. For ULcertified installations that are utilizing SWIFT devices, the

value must be set to 4 hours.

• Call forwarding shall not be used.

• When two count is used: detector spacing shall be cut in half, you shall not use the alarm verification feature, and no delay shall be used.

• P.A.S. (positive alarm sequence) feature shall be used only with automatic detectors.

2.2.2 UL 864 9th and 10th Edition

• Per the UL Continuing Certification Program, UL864 9th edition fire alarm control equipment will retain certification after the roll-out

of UL 10th edition (12/2/2018).

• Installations of UL 864 10th Edition certified equipment are permitted to use UL864 9th Edition certified equipment when approved by

the local Authority Having Jurisdiction (AHJ).

For product compliance, refer to the UL/ULC listing cards located on the UL online certification directory. https://iq.ulprospector.com

2.2.3 Requirements for Central Station Fire Alarm Systems

1. Use both phone lines. Enable phone line monitors for both lines.

2. You must program a phone number and a test time so that the FCP-2100 shall automatically initiate and complete a test signal

transmission sequence to its associated receiver at least once every 6 hours, using two phones or one phone line with Ethernet backup.

3. The AC Loss Hours option must be set from 1-3 hours.

4. If using wired Ethernet, you must program the corresponding account/subscriber ID and a test time so that the FACP shall automatically

initiate a test signal transmission sequence to its associated receiver at least once every 6 hours.

2.2.4 Requirements for Local Protected Fire Alarm Systems

At least one UL listed supervised notification appliance must be used.

2.2.5 Requirements for Remote Station Protected Fire Alarm Systems

Minimum system requirements are one Fike addressable initiating device and either a 5220, Keltron 3158, or the built-in Digital Alarm

Communicator Transmitter (DACT).

1. Do not exceed the current draw load restrictions shown in Section 3.5.

2. The AC Loss Hours option must be set from 1-3 hours.

2.2.6 Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning

Equipment, NFPA 720

When using carbon monoxide detection the system must be monitored by a Supervising Station with emergency response, both aspects meet-

ing the Standard for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 720.

16 FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Agency Listings, Approvals, and Requirements Underwriters Laboratories (UL)

2.2.7 NFPA Requirements

The following is the minimum configuration to meet NFPA requirements.

Model/Module Description Local Releasing Auxiliary Remote

Station Central

Station

FCP-2100 Control Unit YYYYY

FIK-6861BIA annunciator YYYYY

RFCP-2100 Remote unit O O O O O

FIK-6815 SLC Expander OOOOO

FIK-5824 Serial card OOOOO

5220 Rev Polarity Module O O Y Y O

FIK-NIC NetworkcardOOOOO

FIK-FML Fiber module OOOOO

FIK-FSL Fiber module OOOOO

Y = YES, N = NO, O = OPTIONAL

Table 2.1 NFPA Requirements for FCP-2100, FCP-2100HV, RFCP-2100, or RFCP-2100HV

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 17

Underwriters Laboratories (UL) Agency Listings, Approvals, and Requirements

Model/Module Description Local Releasing Auxiliary Remote

Station Central

Station

Mass

Notification

(In-Building) Emergency EVAC

FCP-2100ECS Control Unit Y Y Y Y Y Y Y Y

FIK-6861BIA Annunciator Y Y Y Y Y Y Y Y

FIK-EMG LED / switch card Y Y Y Y Y Y Y Y

5220 Direct Conn

Module OO Y YO N O N

FIK-5496 Indicating Circuit

Expander OO O OO O O O

FIK-5824 Serial/Parallel

Interface OO O OO O O O

FIK-5865-3, FIK-

5865-4 Remote

Annunciator OO O OO O O O

FIK-5880 Remote

Annunciator OO O OO O O O

FIK-5883 Relay Module O O O O O N O N

FIK-6815 SLC expander O O O O O O O O

FIK-NIC Network card O O O O O O O O

FIK-NVCM Network Voice

Control Mod OO O OO O O O

FIK-FML, FIK-FSL Network Fiber Mod O O O O O O O O

FIK-M500R Control Mod O O Y O O N O N

FIK-RPS1000 Power Expander O O O O O O O O

RBB Accessory cabinet O O O O O O O O

FIK-DUAL50W Amplifier N N N N N Y1OY

FIK-50W Amplifier N N N N N Y1OY

FIK-125W Amplifier N N N N N Y1OY

FIK-SW24 Switch

Annunciator NN N NN Y O Y

FIK-RVM Remote Voice

Module NN N NN Y O Y

FIK-INT50W Amplifier N N N N N Y O Y

Y = YES, N = NO, O = OPTIONAL

1. At least one of the following amplifiers is required for MNS operation as well as EVAC: FIK-DUAL50W, FIK-50W, FIK-125W or FIK-INT50W.

Table 2.2 NFPA Requirements for FCP-2100ECS

18 FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Section 3: Before You Begin Installation

This section of the manual is intended to help you plan your tasks to facilitate a smooth installation. Please read this section thoroughly, espe-

cially if you are installing a FCP-2100 panel for the first time.

3.1 Inventory

When the FCP-2100shipment is received, check that all the parts have been included in the shipment. The shipment consist of one of each of

the following:

• main circuit board with display

• backbox with door.

• plastic bag containing two keys, screws, cables, and ten 4.7K ohm end-of-line resistors

• manual

3.2 Environmental Specifications

It is important to protect the FCP-2100 control panel from water. To prevent water damage, the following precautions should be followed

when installing the units:

• Intended for indoor use in dry locations only

• Do not mount directly on exterior walls, especially masonry walls (condensation)

• Do not mount directly on exterior walls below grade (condensation)

• Protect from plumbing leaks

• Protect from splash caused by sprinkler system inspection ports

• Do not mount in areas with humidity-generating equipment (such as dryers, production machinery)

When selecting a location to mount the FCP-2100 control panel, the unit should be mounted where it will NOT be exposed to: temperatures

outside the range of 0°C- 49°C (32°F-120°F) or humidity exceeding 93% non-condensing.

3.3 Software Downloads

In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades

to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that

you download the most current version of software for each product prior to commissioning any system. Contact Technical Support with any

questions about software and the appropriate version for a specific application. Software updates can be found at www.fike.com.

3.4 Electrical Specifications

Table 3.1 lists the terminal block on the FCP-2100 as well as a description of each individual terminal and their respective electrical rating.

Terminal Label Description Rating Earth Ground

Faults

Voltage Current

B AC input (hot) 120 VAC, 60 Hz

240 VAC, 50/60 Hz 5A for the FCP-2100

4.5A for the FCP-2100ECS

2.8A for the FCP-2100HV/ECSHV

N/A

G Earth ground N/A N/A N/A

W AC input (neutral) 120 VAC, 60 Hz

240 VAC, 50/60 Hz 5A for the FCP-2100

4.5A for the FCP-2100ECS

2.8A for the FCP-2100HV/ECSHV

N/A

X1I/O 1 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X1I/O 2 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X1I/O 3 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X1I/O 4 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X1I/O 5 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

Table 3.1 Terminal Descriptions and Electrical Specifications

FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022 19

Electrical Specifications Before You Begin Installation

X1I/O 6 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X1I/O 7 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X1I/O 8 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

B SBUS1 OUT SBUS communication 5 VDC 100 mA 0Ω

+ SBUS power 24 VDC 1.0A

B SBUS1 IN Used for Class Ainstallations 0Ω

B SBUS2 OUT SBUS communication 5 VDC 100 mA 0Ω

+ SBUS power 24 VDC 1.0A

B SBUS2 IN Used for Class Ainstallations 0Ω

N.C. RELAY 1 General Purpose Relay 1 24 VDC 2.5A, resistive N/A

N.O.

N.C. RELAY 2 General Purpose Relay 2 24 VDC 2.5A, resistive N/A

N.O.

N.C. TROUBLE Trouble Relay 24 VDC 2.5 A, resistive N/A

N.O.

S- SLC OUT SLC terminals 32 VDC 150 mA 0Ω

S+

S- SLC PGM SLC Programming 32 VDC 150 mA 0Ω

S+

S- SLC IN Used for Class Ainstallations 0Ω

S+

Ring Phone Line 1 Telco Ring N/A 0Ω

Tip Phone Line 1 Telco Tip

Ring Phone Line 1 Premises Ring

Tip Phone Line 1 Premises Tip

Ring Phone Line 2 Telco Ring N/A 0Ω

Tip Phone Line 2 Telco Tip

Ring Phone Line 2 Premises Ring

Tip Phone Line 2 Premises Tip

Terminal Label Description Rating Earth Ground

Faults

Voltage Current

Table 3.1 Terminal Descriptions and Electrical Specifications

20 FCP-2100/ECS Manual — P/N LS10143-002FK-E:B 6/20/2022

Before You Begin Installation Calculating Current Draw and Standby Battery

3.5 Calculating Current Draw and Standby Battery

This section is for helping you determine the current draw and standby battery needs for your installation.

3.5.1 Current Draw Worksheet Requirements

The following steps must be taken when determining FCP-2100 current draw and standby battery requirements.

1. For the FCP-2100, the worst case current draw is listed for the panel, addressable devices, and SLC expanders. Fill in the number of

addressable devices and expanders that will be used in the system and compute the current draw requirements for alarm and standby.

Record this information in the current draw worksheet on LineA.

2. Add up the current draw for all auxiliary devices and record in the table on Line B.

3. Add up the current draw for all notification appliance loads and record in the table on Line C.

4. For notification appliances and auxiliary devices not mentioned in the manual, refer to the device manual for the current ratings.

5. Make sure that the total alarm current you calculated, including current for the panel itself, does not exceed 9.0A. This is the maximum

alarm current for the FCP-2100 control panel. If the current is above 9.0 A you will need to use a notification power expander(s) such as

the FIK-5496 or the FIK-RPS1000 intelligent power expander, to distribute the power loads so that the FCP-2100 or the power

expanders do not exceed their power ratings. Refer to the current draw worksheets provided with the FIK-5496 or the FIK-RPS1000

manuals so you do not exceed their power ratings.

6. Alternatively, you may network additional FCP-2100 panels to get additional power.

7. Complete the remaining instructions in the appropriate current draw worksheet for determining battery size requirements.

3.5.2 Current Draw Worksheet for Fike SLC Devices

Use Table 3.2 to determine current requirements during alarm/battery standby operation when SLC devices are installed. You can install up

to 159 sensors per loop (2100 points max per panel) and 159 modules per loop (2,100 points max per panel). Copy this section if additional

space is required.

+ Battery Battery Connection 24 VDC 1.12 A N/A

–

P7 Data

Network Used for FIK-NIC 24 VDC 21 mA 0Ω

P8 Voice

Network Used For FIK-NVCM 24 VDC 59 mA 0Ω

1 Regulated for NAC circuits, special application when used for releasing or auxiliary power circuits

Terminal Label Description Rating Earth Ground

Faults

Voltage Current

Table 3.1 Terminal Descriptions and Electrical Specifications

Device # of Devices Current per Device Standby

Current Alarm Current

For each device use this formula: This column X This column = Current per number of devices.

Fire Panel

(Current draw from battery) 1 Standby 230 mA 230 mA

Alarm: 415 mA 415 mA1

Addressable SLC Detectors

FIK-2351

Standby: 0.2 mA

Alarm: 4.5 mA2

mA mA

FIK-2351T mA mA

FIK-2351R mA mA

FIK-5351 mA mA

FIK-5351H mA mA

FIK-5351R mA mA

OSI-RI-FIK SLC Standby/Alarm: 20 mA mA mA

Aux. Pwr Standby: 22 mA mA

Alarm: 20 mA mA

DNR/DNRW3(non-relay) None, included with FIK-2351R

DNR3(with relay) None, included with FIK-2351R & FIK-M500R

FIK-FC351 SLC Standby: 0.20 mA mA

Alarm: 4.5 mA mA

Table 3.2 Current Draw Worksheet for IDP SLC Devices

This manual suits for next models

Table of contents

Other Fike Control Panel manuals

Fike

Fike Twinflex pro2 User manual

Fike

Fike TWINFLEXpro User manual

Fike

Fike FCP-75 User manual

Fike

Fike CIE-A-200 User manual

Fike

Fike FIK-5496 User manual

Fike

Fike TWINFLEX SRP 100-0001 User manual

Fike

Fike FCP-300 User manual

Fike

Fike TWINFLEXpro User manual

Fike

Fike SITA200plus User manual

Fike

Fike FIK-RA100BD Technical manual

Fike

Fike FCP-2100 User manual

Fike

Fike FIK-RA2000 Technical manual

Fike

Fike FCP-75 User manual

Fike

Fike GB2426367 User manual

Fike

Fike Quadnet User manual

Popular Control Panel manuals by other brands

Garmin

Garmin GMA 345 pilot's guide

Harvia

Harvia Xenio RGBW CX002RGBW Instructions for installation and use

Compool

Compool Cp3830 Installation & operating instructions

GE Entelli-Switch 250 Operation and maintenance manual

ICP DAS USA

ICP DAS USA TPD-432F-H quick start

Siemens

Siemens SIMATIC HMI OP3 Equipment manual

Stahl

Stahl 8125/5 operating instructions

Tyco

Tyco RAPID RESPONSE RCP-1 manual

Bauer

Bauer LOGICM installation manual

Elentek

Elentek DRYTEK 1 Mono user manual

Genvex

Genvex Optima 250 DESIGN user manual

CG Emotron FDU 2.0 instruction manual

Lightronics

Lightronics FC-816 owner's manual

Gardsman

Gardsman CTC-1132 Installation & operating guide

GJD

GJD HYL004 Installation & programming guide

Endress+Hauser

Endress+Hauser Liquiline CM442 Brief operating instructions

RIB

RIB KS2 24V manual

Bosch

Bosch Rexroth VAM 10.1 Project planning manual

Fike FCP-2100ECS User manual

Popular Control Panel manuals by other brands