Fike Fcp-2100 User manual

P/N LS10143-002FK-E:A • ECN 151526

Document LS10143-002FK-E

3/11/2021 Rev:

Addressable Fire Alarm Control Panel

FCP-2100/FCP-2100ECS

Instruction Manual

2FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Fire Alarm & Emergency Communication System Limitations

While a life safety system may lower insurance rates, it is not a substitute for life and property insurance!

An automatic fire alarm system—typically made up of smoke

detectors, heat detectors, manual pull stations, audible warning

devices, and a fire alarm control panel (FACP) with remote

notification capability—can provide early warning of a developing fire.

Such a system, however, does not assure protection against property

damage or loss of life resulting from a fire.

An emergency communication system—typically made up of an

automatic fire alarm system (as described above) and a life safety

communication system that may include an autonomous control unit

(ACU), local operating console (LOC), voice communication, and

other various interoperable communication methods—can broadcast

a mass notification message. Such a system, however, does not

assure protection against property damage or loss of life resulting

from a fire or life safety event.

The Manufacturer recommends that smoke and/or heat detectors be

located throughout a protected premises following the

recommendations of the current edition of the NationalFire Protection

Association Standard 72 (NFPA 72), manufacturer's

recommendations, State and local codes, and the recommendations

contained in the Guide for Proper Use of System Smoke Detectors,

which is made available at no charge to all installing dealers. This

document can be found at http://www.systemsensor.com/appguides/.

A study by the Federal Emergency ManagementAgency (an agency

of the United States government) indicated that smoke detectors may

not go off in as many as 35% of all fires. While fire alarm systems are

designed to provide early warning against fire, they do not guarantee

warning or protection against fire.A fire alarm system may not

provide timely or adequate warning, or simply may not function, for a

variety of reasons:

Smoke detectors may not sense fire where smoke cannot reach the

detectors such as in chimneys, in or behind walls, on roofs, or on the

other side of closeddoors. Smoke detectors also may notsense a fire

on another level or floor of a building. A second-floor detector, for

example, may not sense a first-floor or basement fire.

Particles of combustion or “smoke” from a developing fire may not

reach the sensing chambers of smoke detectors because:

• Barriers such as closed or partially closed doors, walls, chimneys,

even wet or humid areas may inhibit particle or smoke flow.

• Smoke particles may become “cold,” stratify, and not reach the

ceiling or upper walls where detectors are located.

• Smoke particles may be blown away from detectors by air outlets,

such as air conditioning vents.

• Smoke particles may be drawn into air returns before reaching the

detector.

The amount of “smoke” present may be insufficient to alarm smoke

detectors. Smoke detectors are designed to alarm at various levels of

smoke density. If such density levels are not created by a developing

fire at the location of detectors, the detectors will not go into alarm.

Smoke detectors, even when working properly, have sensing

limitations. Detectors that have photoelectronic sensing chambers

tend to detect smoldering fires better than flaming fires, which have

little visible smoke. Detectors that have ionizing-type sensing

chambers tend to detect fast-flaming fires better than smoldering

fires. Because fires develop in different ways and are often

unpredictable in their growth, neither type of detector is necessarily

best and a given type of detector may not provide adequate warning

of a fire.

Smoke detectors cannot be expected to provide adequate warning of

fires caused by arson, children playing with matches (especially in

bedrooms), smoking in bed, and violent explosions (caused by

escaping gas, improper storage of flammable materials, etc.).

Heat detectors do not sense particles of combustion and alarm only

when heat on their sensors increases at a predetermined rate or

reaches a predetermined level. Rate-of-rise heat detectors may be

subject to reduced sensitivity over time. For this reason, the rate-of-

rise feature of each detector should be tested at least once per year

by a qualified fire protection specialist. Heat detectors are designed to

protect property, not life.

IMPORTANT! Smoke detectors must be installed in the same room

as the control panel and in rooms used by the system for the

connection of alarm transmission wiring, communications, signaling,

and/or power. If detectors are not so located, a developing fire may

damage the alarm system, compromising its ability to report a fire.

Audible warning devices such as bells, horns, strobes, speakers

and displays may not alert people if these devices are located on the

other side of closed or partly open doors or are located on another

floor of a building. Any warning device may fail to alert people with a

disability or those who have recently consumed drugs, alcohol, or

medication. Please note that:

• An emergency communication system may take priority over a fire

alarm system in the event of a life safety emergency.

• Voice messaging systems must be designed to meet intelligibility

requirements as defined by NFPA, local codes, andAuthorities

Having Jurisdiction (AHJ).

• Language and instructional requirements must be clearly dissemi-

nated on any local displays.

• Strobes can, under certain circumstances, cause seizures in peo-

ple with conditions such as epilepsy.

• Studies have shown that certain people, even when they hear a

fire alarm signal, do not respond to or comprehend the meaning of

the signal.Audible devices, such as horns and bells, can have dif-

ferent tonal patterns and frequencies. It is the property owner's

responsibility to conduct fire drills and other training exercises to

make people aware of fire alarm signals and instruct them on the

proper reaction to alarm signals.

• In rare instances, the sounding of a warning device can cause

temporary or permanent hearing loss.

A life safety system will not operate without any electrical power. If

AC power fails, the system will operate from standby batteries only for

a specified time and only if the batteries have been properly

maintained and replaced regularly.

Equipment used in the system may not be technically compatible

with the control panel. It is essential to use only equipment listed for

service with your control panel.

Alarm Signaling Communications:

•IP connections rely on available bandwidth, which could be lim-

ited if the network is shared by multiple users or if ISP policies

impose restrictions on the amount of data transmitted. Service

packages must be carefully chosen to ensure that alarm signals

will always have available bandwidth. Outages by the ISP for

maintenance and upgrades may also inhibit alarm signals. For

added protection, a backup cellular connection is recommended.

•Cellular connections rely on a strong signal. Signal strength can

be adversely affected by the network coverage of the cellular car-

rier, objects and structural barriers at the installation location. Uti-

lize a cellular carrier that has reliable network coverage where the

alarm system is installed. For added protection, utilize an external

antenna to boost the signal.

•Telephone lines needed to transmit alarm signals from a premise

to a central monitoring station may be out of service or temporarily

disabled. For added protection against telephone line failure,

backup alarm signaling connections are recommended.

The most common cause of life safety system malfunction is

inadequate maintenance. To keep the entire life safety system in

excellent working order, ongoing maintenance is required per the

manufacturer's recommendations, and UL and NFPA standards.At a

minimum, the requirements of NFPA 72 shall be followed.

Environments with large amounts of dust, dirt, or high air velocity

require more frequent maintenance.A maintenance agreement

should be arranged through the local manufacturer's representative.

Maintenance should be scheduled as required by National and/or

local fire codes and should be performed by authorized professional

life safety system installers only. Adequate written records of all

inspections should be kept. Limit-F-2020

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 3

Installation Precautions

Adherence to the following will aid in problem-free installation with long-term reliability:

WARNING - Several different sources of power can be con-

nected to the fire alarm control panel. Disconnect all sources of

power before servicing. Control unit and associated equipment may

be damaged by removing and/or inserting cards, modules, or inter-

connecting cables while the unit is energized. Do not attempt to

install, service, or operate this unit until manuals are read and under-

stood.

CAUTION - System Re-acceptance Test after Software Changes:

To ensure proper system operation, this product must be tested in

accordance with NFPA 72 after any programming operation or

change in site-specific software. Re-acceptance testing is required

after any change, addition or deletion ofsystem components, or after

any modification, repair or adjustment to system hardware or wiring.

All components, circuits, system operations, or software functions

known to be affected by a change must be 100% tested. In addition,

to ensure that other operations are not inadvertently affected, at

least 10% of initiating devices that are not directly affected by the

change, up to a maximum of 50 devices, must also be tested and

proper system operation verified.

This system meets NFPA requirements for operation at 0-49º C/32-

120º F and at a relative humidity 93% ± 2% RH (non-condensing) at

32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's

standby batteries and the electronic components may be adversely

affected by extreme temperature ranges and humidity. Therefore, it

is recommended that this system and its peripherals be installed in

an environment with a normal room temperature of 15-27º C/60-80º

Verify that wire sizes are adequate for all initiating and indicating

device loops. Most devices cannot tolerate more than a 10% I.R.

drop from the specified device voltage.

Like all solid state electronic devices, this system may operate

erratically or can be damaged when subjected to lightning induced

transients.Although no system is completely immune from lightning

transients and interference, proper grounding will reduce susceptibil-

ity. Overhead or outside aerial wiring is not recommended, due to an

increased susceptibility to nearby lightning strikes. Consult with the

Technical Services Department if any problems are anticipated or

encountered.

Disconnect AC power and batteries prior to removing or inserting

circuit boards. Failure to do so can damage circuits.

Remove all electronic assemblies prior to any drilling, filing, ream-

ing, or punching of the enclosure. When possible, make all cable

entries from the sides or rear. Before making modifications, verify

that they will not interfere with battery, transformer, or printed circuit

board location.

Do not tighten screw terminals more than 9 in-lbs. Over-tightening

may damage threads, resulting in reduced terminal contact pressure

and difficulty with screw terminal removal.

This system contains static-sensitive components. Always

ground yourself with a proper wrist strap before handling any circuits

so that static charges are removed from the body. Use static sup-

pressive packaging to protect electronic assemblies removed from

the unit.

Units with a touchscreen display should be cleaned with a dry,

clean, lint free/microfiber cloth. If additional cleaning is required,

apply a small amount of Isopropyl alcohol to the cloth and wipe

clean. Do not use detergents, solvents, or water for cleaning. Do not

spray liquid directly onto the display.

Follow the instructions in the installation, operating, and program-

ming manuals.These instructions must be followed to avoid damage

to the control panel and associated equipment. FACP operation and

reliability depend upon proper installation.

Precau-D2-11-2017

FCC Warning

WARNING: This equipment generates, uses, and can radi-

ate radio frequency energy and if not installed and used in

accordance with the instruction manual may cause interfer-

ence to radio communications. It has been tested and found

to comply with the limits for classA computing devices pur-

suant to Subpart B of Part 15 of FCC Rules, which is

designed to provide reasonable protection against such

interference when devices are operated in a commercial

environment. Operation of this equipment in a residential

area is likely to cause interference, in which case the user

will be required to correct the interference at his or her own

expense.

Canadian Requirements

This digital apparatus does not exceed the Class A limits for

radiation noise emissions from digital apparatus set out in

the Radio Interference Regulations of the Canadian Depart-

ment of Communications.

Le present appareil numerique n'emet pas de bruits radio-

electriques depassant les limites applicables aux appareils

numeriques de la classeAprescrites dans le Reglement sur

le brouillage radioelectrique edicte par le ministere des

Communications du Canada.

eVance®, Flexput®, Honeywell®, JumpStart®, and SWIFT® are registered trademarks of Honeywell International Inc. Microsoft® and Windows® are registered

trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered trademark of The Mozilla Foundation.

4FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Software Downloads

In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent

upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly

recommend that you download the most current version of software for each product prior to commissioning any system. Contact

Technical Support with any questions about software and the appropriate version for a specific application.

Documentation Feedback

Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions about our online

Help or printed manuals, you can email us.

Please include the following information:

• Product name and version number (if applicable)

• Printed manual or online Help

• Topic Title (for online Help)

• Page number (for printed manual)

• Brief description of content you think should be improved or corrected

• Your suggestion for how to correct/improve documentation

Send email messages to:

[email protected]

or call (800)979-3453, x21 in US or (816)229-3405 international

This symbol (shown left) on the product(s) and / or accompanying documents means that used electrical and electronic products

should not be mixed with general household waste. For proper treatment, recovery and recycling, contact your local authorities or

dealer and ask for the correct method of disposal.

Electrical and electronic equipment contains materials, parts and substances, which can be dangerous to the environment and harmful

to human health if the waste of electrical and electronic equipment (WEEE) is not disposed of correctly.

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 5

Table of Contents

Section 1: Introduction ................................................................................................................................................... 10

1.1: Overview of Basic System...............................................................................................................................................................................10

1.1.1: Hardware Features................................................................................................................................................................................10

1.1.2: Network System Hardware Features ....................................................................................................................................................10

1.1.3: Software Features .................................................................................................................................................................................10

1.1.4: FCP-2100ECS Features........................................................................................................................................................................10

1.1.5: Terms Used in this Manual...................................................................................................................................................................11

1.2: Compatible Products........................................................................................................................................................................................11

Section 2: Agency Listings, Approvals, and Requirements........................................................................................ 13

2.1: Federal Communications Commission (FCC).................................................................................................................................................13

2.2: Underwriters Laboratories (UL)......................................................................................................................................................................13

2.2.1: Requirements for All Installations........................................................................................................................................................13

2.2.2: Requirements for Central Station Fire Alarm Systems ........................................................................................................................14

2.2.3: Requirements for Local Protected Fire Alarm Systems.......................................................................................................................14

2.2.4: Requirements for Remote Station Protected Fire Alarm Systems........................................................................................................14

2.2.5: Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 720..................................14

2.2.6: NFPA Requirements.............................................................................................................................................................................14

Section 3: Before You Begin Installation...................................................................................................................... 16

3.1: Inventory..........................................................................................................................................................................................................16

3.2: Environmental Specifications..........................................................................................................................................................................16

3.3: Software Downloads........................................................................................................................................................................................16

3.4: Electrical Specifications ..................................................................................................................................................................................16

3.5: Wiring Specifications.......................................................................................................................................................................................18

3.6: Board Assembly Diagram................................................................................................................................................................................20

3.7: Calculating Current Draw and Standby Battery..............................................................................................................................................21

3.7.1: Current Draw Worksheet Requirements...............................................................................................................................................21

3.7.2: Current Draw Worksheet for Fike IDP SLC Devices .........................................................................................................................21

3.7.3: Maximum Battery Standby Load..........................................................................................................................................................24

Section 4: Control Panel Installation............................................................................................................................. 25

4.1: Mounting the Control Panel Cabinet...............................................................................................................................................................25

4.1.1: Preventing Water Damage....................................................................................................................................................................25

4.1.2: Removing the FCP-2100 Assembly from the Housing........................................................................................................................25

4.1.3: Ethernet Connection .............................................................................................................................................................................25

4.2: AC Power Connection .....................................................................................................................................................................................25

4.3: Battery Power ..................................................................................................................................................................................................26

4.3.1: Battery Accessory Cabinets..................................................................................................................................................................27

4.4: SBUS Wiring ...................................................................................................................................................................................................28

4.4.1: Calculating Wiring Distance for SBUS Modules.................................................................................................................................28

4.4.2: Wiring Configurations..........................................................................................................................................................................31

4.5: FIK-RA2000 Remote Annunciator Installation...............................................................................................................................................32

4.5.1: Mounting the FIK-RA2000 ..................................................................................................................................................................33

4.5.2: FIK-RA2000 Connection to the Panel..................................................................................................................................................35

4.5.3: Temporary Programming Display........................................................................................................................................................35

4.6: FIK-RA1000R Remote Annunciator Installation............................................................................................................................................36

4.6.1: Mounting the FIK-RA1000R................................................................................................................................................................36

4.6.2: Model FIK-RA1000R Connection to the Panel....................................................................................................................................39

4.7: FIK-RA100 Remote Annunciator Installation.................................................................................................................................................39

4.7.1: Mounting the FIK-RA100 ....................................................................................................................................................................40

4.7.2: Model FIK-RA100 Connection to the Panel ........................................................................................................................................43

4.8: FIK-6815 Installation.......................................................................................................................................................................................43

4.8.1: FIK-6815 Connection to the Panel .......................................................................................................................................................44

4.9: FIK-5824 Serial/Parallel Interface Module Installation ..................................................................................................................................44

4.9.1: Selecting FIK-5824 Options.................................................................................................................................................................45

4.10: FIK-5880 LED I/O Module...........................................................................................................................................................................46

4.10.1: FIK-5880 Board Layout .....................................................................................................................................................................46

4.10.2: FACP Connection...............................................................................................................................................................................47

4.10.3: LED Wiring ........................................................................................................................................................................................47

4.10.4: Dry Contact Wiring ............................................................................................................................................................................48

4.11: FIK-5865-3 / FIK-5865-4 LED Annunciator Installation..............................................................................................................................48

6FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Table of Contents

4.11.1: FACP Connection...............................................................................................................................................................................49

4.11.2: FIK-5865 Mounting............................................................................................................................................................................50

4.12: Configuring SBUS Modules..........................................................................................................................................................................50

4.12.1: Assigning SBUS Module IDs.............................................................................................................................................................50

4.12.2: SBUS Bandwidth Considerations.......................................................................................................................................................51

4.13: Telephone Connection ...................................................................................................................................................................................51

4.14: Flexputs I/O Circuits......................................................................................................................................................................................52

4.14.1: Conventional Notification Appliance.................................................................................................................................................52

4.14.2: Conventional Input Switch Circuits....................................................................................................................................................53

4.14.3: Installing 2-Wire Smoke Detectors ....................................................................................................................................................54

4.14.4: Installing 4-Wire Smoke Detectors ....................................................................................................................................................55

4.14.5: Auxiliary Power Installation...............................................................................................................................................................56

4.15: On-Board Relays (Conventional) ..................................................................................................................................................................57

4.15.1: Trouble Relay .....................................................................................................................................................................................57

4.15.2: Programmable Relays.........................................................................................................................................................................57

4.16: Remote Station Applications .........................................................................................................................................................................57

4.16.1: Keltron Model 3158 Installation.........................................................................................................................................................57

4.16.2: City Box Connection Using the 5220 Module ...................................................................................................................................58

4.16.3: Using the Addressable Relay Module for City Box Connection........................................................................................................59

4.16.4: NFPA 72 Polarity Reversal ................................................................................................................................................................59

4.16.5: Transmitter Activated by Dry Contacts..............................................................................................................................................60

Section 5: Networking..................................................................................................................................................... 61

5.1: Network System Hardware Features ...............................................................................................................................................................61

5.1.1: Networked Sites....................................................................................................................................................................................61

5.1.2: Wiring Options to Connect Networked Panels.....................................................................................................................................61

5.2: Model RFCP-2100...........................................................................................................................................................................................61

5.3: Network Wiring ...............................................................................................................................................................................................61

5.4: FIK-NIC Wiring Options.................................................................................................................................................................................62

5.4.1: Fiber Loop Modules .............................................................................................................................................................................63

5.4.2: FIK-NIC Installation.............................................................................................................................................................................63

5.5: Setting the Network ID for each Panel............................................................................................................................................................69

Section 6: Network Management ................................................................................................................................... 70

6.1: Network Diagnostics .......................................................................................................................................................................................70

6.1.1: Ping Panel.............................................................................................................................................................................................70

6.1.2: Data Network Status............................................................................................................................................................................70

6.1.3: Voice Network Status...........................................................................................................................................................................70

6.2: Network Programming ....................................................................................................................................................................................70

6.2.1: Learn Network......................................................................................................................................................................................70

6.2.2: Edit Network Names.............................................................................................................................................................................70

6.2.3: Edit Panel ID.........................................................................................................................................................................................70

6.2.4: Computer Access..................................................................................................................................................................................71

6.2.5: Access Codes........................................................................................................................................................................................71

6.2.6: Communicator Options.........................................................................................................................................................................72

6.3: Voice Options...................................................................................................................................................................................................73

6.3.1: Edit Timers ...........................................................................................................................................................................................73

6.3.2: Edit Voice Commands..........................................................................................................................................................................74

6.4: Sync Network Options.....................................................................................................................................................................................74

6.5: Network Management Quick Reference .........................................................................................................................................................75

Section 7: Fike IDP and SWIFT SLC Device Installation.............................................................................................. 78

7.1: List of Fike IDP SLC Devices.........................................................................................................................................................................78

7.2: SWIFT Wireless SLC Devices ........................................................................................................................................................................78

7.3: Maximum Number of SLC Devices................................................................................................................................................................78

7.4: Wiring Requirements for SLC Devices...........................................................................................................................................................78

7.4.1: Wire Sizing for FIK-6815.....................................................................................................................................................................79

7.4.2: Wiring Requirements for Fike IDP Modules........................................................................................................................................79

7.4.3: Wiring FIK-6815 in Style 6 & 7 (Class A) Configuration...................................................................................................................80

7.5: Addressing Fike IDP SLC Devices..................................................................................................................................................................81

7.5.1: SLC Devices with DIP Switches..........................................................................................................................................................82

7.6: Wiring the FIK-W-WGI...................................................................................................................................................................................82

7.6.1: Power Connections for the Gateway ....................................................................................................................................................82

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 7

Table of Contents

Section 8: Programming Overview................................................................................................................................ 83

8.1: JumpStart AutoProgramming ..........................................................................................................................................................................83

8.1.1: Input Points...........................................................................................................................................................................................83

8.1.2: Output Points........................................................................................................................................................................................83

8.1.3: Running JumpStart AutoProgramming ................................................................................................................................................83

8.2: Mapping Overview..........................................................................................................................................................................................84

8.2.1: Input Point Mapping.............................................................................................................................................................................85

8.2.2: Output Circuit Mapping........................................................................................................................................................................86

8.2.3: Event Mapping.....................................................................................................................................................................................86

8.2.4: Mapping LED Points............................................................................................................................................................................90

8.2.5: Mapping LED Points for a Networked System....................................................................................................................................91

8.3: Programming Using the HFSS Programming Tool.........................................................................................................................................91

8.4: Programming Using an Annunciator ...............................................................................................................................................................91

8.4.1: Entering / Exiting Panel Programming.................................................................................................................................................91

8.5: Programming Menu Quick Reference.............................................................................................................................................................93

Section 9: Programming............................................................................................................................................... 103

9.1: UL 864 / UL 2572 Programming Requirements............................................................................................................................................103

9.2: Modules .........................................................................................................................................................................................................103

9.2.1: Edit Modules.......................................................................................................................................................................................103

9.2.2: Adding a Module................................................................................................................................................................................104

9.2.3: Deleting a Module ..............................................................................................................................................................................104

9.2.4: View Module List...............................................................................................................................................................................104

9.3: Zone...............................................................................................................................................................................................................104

9.3.1: Edit Zone ............................................................................................................................................................................................104

9.3.2: View Zone Points ...............................................................................................................................................................................106

9.4: Group.............................................................................................................................................................................................................106

9.4.1: Edit Group ..........................................................................................................................................................................................106

9.4.2: View Group Points .............................................................................................................................................................................108

9.4.3: Edit OPG Template.............................................................................................................................................................................108

9.5: Point...............................................................................................................................................................................................................108

9.5.1: Point Programming For FIK-6815 Module........................................................................................................................................108

9.5.2: Point Programming For Internal or External Power Module (FIK-RPS1000)...................................................................................111

9.5.3: Point Programming For FIK-5880/FIK-5865 Modules......................................................................................................................112

9.5.4: Point Programming for FIK-5496 ......................................................................................................................................................113

9.5.5: Point Programming for Fike Amplifiers (FIK-50W/FIK-125W).......................................................................................................113

9.5.6: Point Programming for FIK-NVCM or FIK-RVM ............................................................................................................................114

9.6: System Options..............................................................................................................................................................................................115

9.6.1: Communication Options.....................................................................................................................................................................115

9.6.2: Daytime/Nighttime Sensitivity...........................................................................................................................................................118

9.6.3: Holiday Days ......................................................................................................................................................................................118

9.6.4: Time Options ......................................................................................................................................................................................118

9.6.5: Miscellaneous Options........................................................................................................................................................................119

9.6.6: Daylight Saving Options.....................................................................................................................................................................120

9.6.7: Edit Banner.........................................................................................................................................................................................120

9.7: JumpStart AutoProgramming ........................................................................................................................................................................120

9.8: Restore Defaults.............................................................................................................................................................................................121

9.9: Voice Options.................................................................................................................................................................................................121

9.9.1: VCM Maintenance..............................................................................................................................................................................121

9.9.2: Voice Settings.....................................................................................................................................................................................121

Section 10: System Operation...................................................................................................................................... 122

10.1: Default User and Installer Codes.................................................................................................................................................................122

10.2: Annunciator Description..............................................................................................................................................................................122

10.2.1: LCD Display.....................................................................................................................................................................................122

10.2.2: Banner...............................................................................................................................................................................................123

10.3: Menu System ..............................................................................................................................................................................................123

10.3.1: Main Menu Overview.......................................................................................................................................................................123

10.3.2: Using the Menus...............................................................................................................................................................................123

10.4: Basic Operation ...........................................................................................................................................................................................123

10.4.1: Setting Time and Date ......................................................................................................................................................................123

10.4.2: Disable / Enable a Point....................................................................................................................................................................124

10.4.3: View Event History ..........................................................................................................................................................................124

8FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Table of Contents

10.4.4: Conduct a Fire Drill..........................................................................................................................................................................124

10.4.5: Conduct an Indicator Test.................................................................................................................................................................124

10.4.6: Conduct a Walk Test ........................................................................................................................................................................125

10.4.7: Conduct a Communicator Test.........................................................................................................................................................125

10.4.8: Manual AlarmNet Registration.........................................................................................................................................................125

10.4.9: Silence Alarms or Troubles ..............................................................................................................................................................125

10.4.10: Reset Alarms...................................................................................................................................................................................125

10.4.11: Check Detector Sensitivity Through Point Status.........................................................................................................................126

10.4.12: View Status of a Point ...................................................................................................................................................................126

10.4.13: View Alarms or Troubles ..............................................................................................................................................................126

10.4.14: System Information .......................................................................................................................................................................126

10.5: Event Priority..............................................................................................................................................................................................127

10.5.1: System Control .................................................................................................................................................................................127

10.5.2: System Override ...............................................................................................................................................................................127

10.5.3: Event Priority....................................................................................................................................................................................127

10.5.4: Priority Rules....................................................................................................................................................................................128

10.5.5: Other Priority Considerations...........................................................................................................................................................128

10.6: Operation Mode Behavior ...........................................................................................................................................................................128

10.6.1: Multi-Site Annunciator and Multi-Site User Access........................................................................................................................131

10.7: Releasing Operations...................................................................................................................................................................................131

10.7.1: Single Interlock Zone Releasing.......................................................................................................................................................132

10.7.2: Double Interlock Zone Releasing .....................................................................................................................................................133

10.8: Smoke Alarm Verification ...........................................................................................................................................................................134

10.9: Function Keys.............................................................................................................................................................................................134

10.9.1: Recording an F-Key Macro ..............................................................................................................................................................134

10.9.2: Aborting an F-Key Macro Recording Session..................................................................................................................................134

10.9.3: Erasing an F-Key Macro...................................................................................................................................................................134

10.9.4: Using a Recorded F-Key Macro.......................................................................................................................................................134

10.9.5: F-Key Status Event...........................................................................................................................................................................134

10.9.6: F-Key Map Inhibit............................................................................................................................................................................134

Section 11: Emergency Communication System Operation..................................................................................... 135

11.1: Overview......................................................................................................................................................................................................135

11.2: LOC Functionality.......................................................................................................................................................................................135

11.2.1: Keys and LEDs.................................................................................................................................................................................135

11.2.2: Gaining ECS Control........................................................................................................................................................................136

11.2.3: Manual ECS......................................................................................................................................................................................137

11.2.4: Microphone Mode ............................................................................................................................................................................137

11.2.5: Message Mode..................................................................................................................................................................................137

11.2.6: Custom ECS Event ...........................................................................................................................................................................137

11.2.7: Passing ECS Control.........................................................................................................................................................................138

11.2.8: Exit ECS Control Menu....................................................................................................................................................................138

11.2.9: Relinquish ECS Control ...................................................................................................................................................................138

11.2.10: ECS Reset .......................................................................................................................................................................................138

11.3: ECS Super User ...........................................................................................................................................................................................138

11.4: ECS Point Functionality ..............................................................................................................................................................................139

11.4.1: ECS Point Activations......................................................................................................................................................................139

11.4.2: FIK-NVCM and FIK-RVM Points...................................................................................................................................................139

11.5: Amplifier Programming...............................................................................................................................................................................139

11.5.1: Adding an Amplifier.........................................................................................................................................................................139

11.5.2: Editing an Amplifier.........................................................................................................................................................................139

11.6: LOC Programming.......................................................................................................................................................................................139

11.6.1: Adding an LOC.................................................................................................................................................................................139

11.6.2: Editing an LOC.................................................................................................................................................................................140

11.7: Using the Microphone..................................................................................................................................................................................140

11.7.1: Microphone Functionality ................................................................................................................................................................140

11.7.2: Custom ECS Event ...........................................................................................................................................................................140

11.7.3: Fire Page...........................................................................................................................................................................................140

11.7.4: Emergency Page ...............................................................................................................................................................................141

11.8: Recording Custom Messages.......................................................................................................................................................................141

11.8.1: Recording Messages 1-15 Using Aux Audio Input..........................................................................................................................142

11.8.2: Recording Messages 1-15 Using the Microphone............................................................................................................................144

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 9

Table of Contents

11.8.3: Erasing User Message.......................................................................................................................................................................145

11.8.4: Using HFSS Voice Message Load Software....................................................................................................................................145

11.9: Network Paging ...........................................................................................................................................................................................146

Section 12: Reporting ................................................................................................................................................... 147

12.1: Receivers Compatible with the Control Panel.............................................................................................................................................147

12.2: SIA - FCP-2100 Panel PI Modifier Reporting.............................................................................................................................................154

12.3: SIA – FCP-2100 Panel Communicator........................................................................................................................................................154

Section 13: Testing and Troubleshooting...................................................................................................................156

13.1: Troubleshooting...........................................................................................................................................................................................156

13.2: Periodic Testing and Maintenance...............................................................................................................................................................156

13.3: Event History...............................................................................................................................................................................................157

13.4: Built-in Troubleshooting and Testing Tools ................................................................................................................................................157

13.4.1: SLC Device Locater .........................................................................................................................................................................157

13.4.2: SLC Multiple Device Locater...........................................................................................................................................................157

13.4.3: I/O Point Control ..............................................................................................................................................................................158

13.4.4: Earth Fault Resistance ......................................................................................................................................................................158

Section 14: Installation Records.................................................................................................................................. 160

14.1: Detector and Module Point Record .............................................................................................................................................................160

14.2: Additional SLC Devices ..............................................................................................................................................................................161

14.3: Conventional Output Point Record..............................................................................................................................................................163

Appendix A: Compatible Devices ................................................................................................................................ 164

A.1: Notification Appliances ................................................................................................................................................................................164

A.2: Two Wire Detectors ......................................................................................................................................................................................172

A.3: Four-Wire Smoke Detectors/Devices (UL Listed)........................................................................................................................................173

A.4: Door Holders (UL Listed).............................................................................................................................................................................174

A.5: Relays (UL Listed)........................................................................................................................................................................................174

A.6: Compatible 520Hz Signaling Speakers ........................................................................................................................................................175

A.7: Compatible 520Hz Low Frequency Bases....................................................................................................................................................175

Appendix B: Editing Text Using the Built-In Programmer......................................................................................... 176

B.1: Characters Used for Editing Text..................................................................................................................................................................176

B.2: Example Name Edit ......................................................................................................................................................................................176

Appendix C: Cadence Patterns.................................................................................................................................... 177

Appendix D: Expanded Receiver/Panel Relationship................................................................................................ 178

Model FCP-2100 Basic Operating Instructions........................................................................................................... 179

Model FCP-2100ECS Basic Operating Instructions ................................................................................................... 181

......................................................................................................................................................................................... 183

......................................................................................................................................................................................... 185

Note:: To Operate the Microphone:...................................................................................................................................................................185

3.: To Reset the ECS System:.............................................................................................................................................................................185

2.: FIK-LOC2100 Operating Instructions........................................................................................................................................................185

3.: For Pre-recorded Message:...........................................................................................................................................................................185

10 FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Section 1: Introduction

The FCP-2100 and FCP-2100ECS are analog addressable fire alarm control panels (FACP), that meets the requirements of UL 864. The

FCP-2100ECS is ananalog addressable fire control system combined with an Emergency Communication System that meet the requirements

for Mass Notification as described in UL 864 and UL 2572.

The RFCP-2100 is the same as the FCP-2100 without the display. The RFCP-2100 is used in a networked system where there is at least one

FCP-2100/ECS in the system. When using the RFCP-2100 as a stand alone local unit, one LCD annunciator must be connected, and the

annunciator must be wired in conduit within 20’of the RFCP-2100.

1.1 Overview of Basic System

The FCP-2100 base system is packaged as an assembled stack of 3 circuit boards mounted to an aluminum housing.

1.1.1 Hardware Features

• The basic FCP-2100 panel contains one built in signaling line circuit (SLC), which supports up to 159 Fike IDP sensors and 159 Fike

IDP modules. Additional SLC loops can be added to increase overall point capacity.

• Additional FIK-6815 SLC expanders supports 159 Fike IDP sensors and 159 Fike IDP modules for a maximum of 2100 points per

FCP-2100 control panel.

• 9.0A of output power is available through 8 sets of terminals for notification and auxiliary applications. Each circuit is power limited

per UL 864 and can source up to 3.0A (total output power must not exceed 9.0A). The constant auxiliary power load must not exceed

6.0A for normal standby.

• Built-in dual phone line, digital alarm communicator/transmitter (DACT), or IP technologies.

• Reports events to central station by point or by zone.

• UL Listed for pre-action and deluge releasing systems.

• Dedicated Form C trouble relay and two general purpose Form C programmable relays.

• Can be used with FIK-RA2000s

, FIK-RA1000Rs

or FIK-RA100s

in any combination.

• Supports the FIK-5865-3, FIK-5865-4, and FIK-5880 LED annunciators

. See Section 4.10 and Section 4.11 for additional information

on these models.

• Printing of event log available through the FIK-5824

serial/parallel printer interface module.

• Supports conventional 2-wire & 4-wire detectors using the 8 Flexput® circuits or SLC zone modules.

• 999 software zones, 999 output groups.

• Add four notification/auxiliary power circuits with each FIK-5496 Intelligent Power Module.

• Add six Flexput circuits with each FIK-RPS1000 Remote Power Supply.

1. The system can have a maximum of 63 SBUS devices in any combination.

2. FIK-RA1000R and FIK-RA100 can have a maximum of 31 devices used.

1.1.2 Network System Hardware Features

• The default network setup can contain up to 32- FCP-2100 panels connected.

• Network support for up to 32 Sites.

• Each building is referred to as a “site”.

• Panels can be interconnected using CLASS B or CLASS A topology.

• To network panels together use the FIK-NIC network card. Copper wire or fiber optic cable panel connectivity can be used within the

same networked system.

• The network architecture provides true peer to peer capability allowing network survivability for all hardware that remains operational

in the event of partial system failure.

1.1.3 Software Features

• Advanced analog smoke detector features:

– Three sensitivity settings (high, medium, low)

– Automatic drift compensation

– Maintenance alert region

– Point status meets calibrated smoke test requirements for NFPA 72

– Automatic day/night sensitivity adjustment

• “JumpStart AutoProgramming” feature for easy programming

• Non-volatile event history stores 1000 events per panel

• A choice of output patterns available for notification outputs, including ANSI 3.41 temporal signal

• Built-in synchronization appliance support for AMSECO®, Gentex®, System Sensor®, and Wheelock®

1.1.4 FCP-2100ECS Features

• 15 Recordable one minute messages that can be mapped to eight ECS buttons

• ECS messages can be selected as priority over fire

• Support of up to 15 FIK-LOCs

NOTE: All references to FCP-2100HV within this manual are applicable to the FCP-2100HV, FCP-2100ECSHV, and RFCP-2100HV.

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 11

Compatible Products Introduction

• Programmable trigger inputs from an external source, such as a Monaco system, to either the FIK-NVCM, FIK-RVM, FIK-5880, , any

SLC input module, or Flexput module

• Support for up to 16 SBUS addressable amplifiers using a combination of FIK-50W, FIK-125W, FIK-INT50W or FIK-DUAL50W for

a maximum of 2000 watts per system and up to 128 mappable speaker circuits

• Support for dual channel and backup audio using the FIK-DUAL50W amplifier and FIK-50WBU back-up amplifier

• Single enclosure for both Fire and Emergency Control System components

• Support for one FIK-NVCM

1.1.5 Terms Used in this Manual

The following terminology is used with the above mentioned control panels:

1.2 Compatible Products

Table 1.1 lists the products available for use with the FCP-2100.

Term Description

SLC Signaling line circuit

Module The term module is used for all hardware devices except for SLC addressable devices and notification

appliances. This includes the FCP-2100 panel itself and the built-in power supply. It also refers to any

FIK-6815 SLC expansion modules.

Input Point An addressable sensing device, such as a smoke, heat detector or a contact monitor device

Input Zone A protected area made up of input points

Output Point

(or “Output Circuit”) A notification point or circuit for notification appliances. Relay circuits and auxiliary power circuits are

also considered output points

Group (or “Output Group” or

OPG) A group of output points. Operating characteristics are common to all output points in a group

Mapping Mapping is the process of specifying which outputs are activated when certain events occur in the

system. Section 8.2 explains mapping in detail.

Networking Up to 32 panels can be networked.

Network System Consist of any combination of 32 panels of these model numbers: FCP-75, FCP-300, FCP-300ECS,

FCP-2100, FCP-2100ECS, FCP-2100ECSHV, RFCP-2100 or RFCP-2100HV

ECS Emergency Communication System

SWIFT Smart Wireless Integrated Fire Technology

Type of Device Model Description

Fike IDP Addressable SLC Devices See Section 7.1 for a list of compatible devices

SWIFT Wireless SLC Devices See Section 7.2 for a list of compatible devices

Table 1.1 FCP-2100 Compatible Products

12 FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Introduction Compatible Products

Other Modules FIK-5824 Serial/Parallel

Printer Interface Module Allows a printer to be attached for the system for on-site logging. Four

maximum per system.

FIK-6815 SLC EXPANDER Each 6815 supports up to 159 Fike IDP sensors and 159 Fike IDP modules.

The maximum point count for Fike IDP devices is limited to 2100 per panel.

6815 supports System Sensor devices (Fike IDP)

RFCP-2100 Remote Fire

Panel without display Same operation as FCP-2100/HV without display

FIK-RPS1000 (Rev F or

higher) Intelligent Power

Module

Provides additional power, six Flexput circuits, and two Form C relays. See

Model FIK-RPS1000 Installation Instructions P/N LS10259-001FK-E.

FIK-5496 (Rev F or above)

NAC Expander Provides four additional Notification Appliance Circuits/Auxiliary power

FIK-RA2000 LCD Alarm

Annunciator 4x40 LCD annunciator. Same operation, similar appearance as onboard

annunciator. Any combination of supported annunciators for a max of 63.

FIK-RA1000R LCD Alarm

Annunciator 4x20 LCD annunciator. Any combination of supported annunciators for a max

of 31.

FIK-RA100 LCD Alarm

Annunciator 4x20 LCD annunciator. Any combination of supported annunciators for a max

of 31.

FIK-5865-3 and FIK-5865-4

LED Annunciators LED annunciator can display up to 30 LEDs (15 red and 15 yellow). FIK-5865-

4 has key switches for silence and reset, and a system trouble LED.

FIK-5880 (Rev C or above)

LED I/O Module Driver for up to 40 LEDs. Interfaces with customized annunciator boards. In

addition, the FIK-5880 has eight generic switch input points.

FIK-5883 General Purpose

Relay Module Provides 10 Form C relays. Designed to be driven by the FIK-5880. Up to four

FIK-5883s can be used with each FIK-5880 module.

FIK-SW24 24 Switch expander Refer to the Fike ECS-Series

installation manual PN

LS10262-001FK-E for more

info on these accessories.

FIK-NVCM Network Voice Control Module

FIK-50W 50 watt audio amplifier

FIK-125W 125 watt audio amplifier

FIK-INT50W 50 watt internal amplifier

FIK-DUAL50W Dual Channel amplifier

FIK-50WBU Backup daughter card

FIK-CE4 Provides 4 additional audio circuits for the

FIK-50W or the FIK-125W

FIK-RVM Remote Voice Microphone

FIK-NIC Network Interface Card

FIK-LOC2100 Local Operating Console Refer to LS10188-002FK-E

Wireless FIK-W-WGI Wireless Gateway Refer to the SWIFT wireless

Installation Manual P/N

LS10036-000FK-E for more

information on these

accessories.

FIK-W-PHOTO Wireless Photoelectric Smoke Detector w/ 4"

base

FIK-W-ACCLIMATE Wireless Multi criteria photoelectric smoke

detector with thermal (135°F) w/ 4" base

FIK-W-HEAT-ROR Wireless Heat Rate of Rise Detector 135° fixed

w/4” base

FIK-W-HEAT Wireless Heat, 135° fixed Heat Detector w/4”

base

FIK-W-MONITOR Wireless Addressable Monitor module

FIK-W-RELAY Wireless Addressable Relay module

B210W 6" wireless base

Misc. 7860 Telephone Cord RJ31X cord for connecting phone line to the FCP-2100

HFSS Programming Tool For communication and panel programming with a Windows-based computer.

Enables remote viewing of detector status and event history.

RBB Remote Battery Box for mounting backup batteries up to 35AH that are too

large to fit into the main control panel cabinet. Dimensions: 16" W x 10" H x 6"

D (40.64 cm W x 25.4 cm H x 15.24 cm D)

AB-55 Remote Battery Box for mounting backup batteries up to 55AH that are too

large to fit into the main control panel cabinet. Dimensions: 20" W x 12" H x

7.5" D (50.8 cm W x 30.48 cm H x 19.05 cm D)

Type of Device Model Description

Table 1.1 FCP-2100 Compatible Products (Continued)

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 13

Section 2: Agency Listings, Approvals, and Requirements

2.1 Federal Communications Commission (FCC)

The following information must be provided to the telephone company before the FCP-2100/RFCP-2100 can be connected to the phone

lines:

This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the inside cover of this equipment is a

label that contains, among other information, a product identifier. If requested, this information must be provided to the telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68

rules and requirements adopted by the ACTA. A compliant telephone cord (not provided) and modular jack must be utilized with this prod-

uct. It is designed to be used with a modular jack that is also compliant.

The REN (ringer equivalence number) provided on this installation sheet is used to determine the number of devices that may be connected

to the public switched telephone network. This number must not exceed 5.0. Since this product has an REN of 1.0A, the number of devices

is limited. The REN number is embedded in the FCC registration number as 10A.

If the FCP-2100 causes harm to the telephone network, the telephone company will notify you in advance that the temporarily discontinu-

ance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible.

Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equip-

ment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain unin-

terrupted service.

If trouble is experienced with the FCP-2100, for repair or warranty information, please contact 1-800-979-3453 or www.fike.com. If the

equipment is causing harm to the telephone network, the telephone company may request that you disconnect the FCP-2100 until the prob-

lem has been resolved.

This product cannot be adjusted or repaired in the field. It must be returned to the factory for service.

This equipment is not designed for use with party line service. Connection to party line service is subject to state tariffs.You may contact the

state public utility commission, public service commission or corporation commission for information.

Since the FCP-2100 are commercial fire alarm panels, it must be connected upstream of all other equipment utilizing the phone lines. If you

have questions about the installation, contact your telephone company or a qualified installer.

Caution - To ensure proper operation, this equipment must be installed according to the enclosed installation instructions. To verify that the

equipment is operating properly and can successfully report an alarm, this equipment must be tested immediately after installation, and peri-

odically thereafter, according to the enclosed test instructions.

Caution - In order for “alarm dialing equipment” to be able to seize the phone line to report an alarm or other event when other customer

equipment (telephone, answering system, computer modem, etc.) connected to the same line is in use, “alarm dialing equipment” must be

connected to a properly installed RJ31X jack. The RJ31X jack must be connected in series with, and ahead of, all other equipment attached

to the same phone line. Series installation of an RJ31X jack is depicted in the figure below. If you have any questions concerning these

instructions, you should consult your telephone company or a qualified installer about installing the necessary jack and alarm dialing equip-

ment for you.

2.2 Underwriters Laboratories (UL)

2.2.1 Requirements for All Installations

General requirements are described in this section. When installing an individual device, refer to the specific section of the manual for addi-

tional requirements. The following subsections list specific requirements for each type of installation (for example, Central Station Fire

Alarm systems, Local Protected FireAlarm systems, and so on). See Section 10.7 for information on releasing operation.

1. All field wiring must be installed in accordance with NFPA 70 National Electric Code.

2. Use the addressable smoke detectors specified in Section 7.1 and Section 7.2 of this manual and/or conventional detectors listed in the

compatibility chart in Appendix A.

3. Use UL listed notification appliances compatible with the FCP-2100 from those specified in Appendix A of this manual.

4. A full system checkout must be performed any time the panel is programmed.

Restricted Options:

A Manufacturer: Fike

B Model Number: FCP-2100

C FCC registration number: US: HS9AL10A2100

Ringer equivalence: 1.0A

D Type of jack: RJ31X

E Facility Interface Codes: Loop Start: 02LS2

F Service Order Code: 9.0F

WARNING: FCC PART 15

THIS DEVICE HAS BEEN VERIFIED TO COMPLY WITH FCC RULES PART 15. OPERATION IS SUBJECT TO THE

FOLLOWING CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE RADIO INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPTANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

14 FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Agency Listings, Approvals, and Requirements Underwriters Laboratories (UL)

• The loss of AC signal is defaulted to 3 hours, but the system still allows settings from 0 - 30 hours. For UL certified installations, this

number must be set from 1 to 3 hours.

• The system allows the use of non-latching, spot type smoke detectors. This feature may not be used in commercial applications

whereby a general alarm is sounded. It is intended for elevator recall, door holding applications, and hotel/motel room applications.

• The system allows the Alarm Verification confirmation time to be set from 60 to 250 seconds. For UL certified installations the setting

must be a minimum of 60 seconds.

• The systems allows the Auto-resound time to be set to 24 or 4 hours. For ULcertified installations that are utilizing SWIFT devices, the

value must be set to 4 hours.

• Call forwarding shall not be used.

• When two count is used: detector spacing shall be cut in half, you shall not use the alarm verification feature, and no delay shall be used.

• P.A.S. (positive alarm sequence) feature shall be used only with automatic detectors.

2.2.2 Requirements for Central Station Fire Alarm Systems

1. Use both phone lines. Enable phone line monitors for both lines.

2. You must program a phone number and a test time so that the FCP-2100 shall automatically initiate and complete a test signal

transmission sequence to its associated receiver at least once every 6 hrs.

3. The AC Loss Hours option must be set from 1-3 hours.

4. If using wired Ethernet, you must program the corresponding account/subscriber ID and a test time so that the FACP shall automatically

initiate a test signal transmission sequence to its associated receiver at least once every 6hrs.

2.2.3 Requirements for Local Protected Fire Alarm Systems

At least one UL listed supervised notification appliance must be used.

2.2.4 Requirements for Remote Station Protected Fire Alarm Systems

Minimum system requirements are one Fike addressable initiating device and either a 5220, Keltron 3158, or the built-in DigitalAlarm

Communicator Transmitter (DACT).

1. Do not exceed the current draw load restrictions shown in Section 3.7.

2. The AC Loss Hours option must be set from 1-3 hours.

2.2.5 Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning

Equipment, NFPA 720

When using carbon monoxide detection the system must be monitored by a Supervising Station.

2.2.6 NFPA Requirements

The following is the minimum configuration to meet the NFPA requirements

Model/Module Description Local Releasing Auxiliary Remote

Station Central

Station

021000 Motherboard YYYYY

RFCP-2100 Remote unit O O O O O

5220 Rev Pol Mod O O Y Y O

FIK-5824 Serial card OOOOO

FIK-6815 SLC Expander OOOOO

FIK-NIC NetworkcardOOOOO

FIK-FML Fiber module OOOOO

FIK-FSL Fiber module OOOOO

FIK-6861BIA annunciator YYYYY

Y = YES, N = NO, O = OPTIONAL

Table 2.1 NFPA Requirements for FCP-2100, FCP-2100HV, RFCP-2100, or RFCP-2100HV

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 15

Underwriters Laboratories (UL) Agency Listings, Approvals, and Requirements

Model/Module Description Local Releasing Auxiliary Remote

Station Central

Station

Mass

Notification

(In-Building) Emergency EVAC

021000 Motherboard Y Y Y Y Y Y Y Y

FIK-6861BIA Annunciator

boards YY Y Y Y Y Y Y

FIK-EMG LED / switch card Y Y Y Y Y Y Y Y

5220 Direct Conn

Module OO Y Y O N O N

FIK-5496 Indicating Circuit

Expander OO O O O O O O

FIK-5824 Serial/Parallel

Interface OO O O O O O O

FIK-5865-3,

FIK-5865-4 Remote

Annunciator OO O O O O O O

FIK-5880 Remote

Annunciator OO O O O O O O

FIK-5883 Relay Module O O O O O N O N

FIK-6815 SLC expander O O O O O O O O

FIK-NIC Network card O O O O O O O O

FIK-NVCM Network Voice

Control Mod OO O O O O O O

FIK-FML, FIK-FSL Network Fiber Mod O O O O O O O O

FIK-M500R Control Mod O O Y O O N O N

FIK-RPS1000 Power Expander O O O O O O O O

RBB Accessory cabinet O O O O O O O O

FIK-DUAL50W Amplifier N N N N N Y

FIK-50W Amplifier N N N N N Y

FIK-125W Amplifier N N N N N Y

FIK-SW24 Switch

Annunciator NN N N N Y O Y

FIK-RVM Remote Voice

Module NN N N N Y O Y

FIK-INT50W Amplifier N N N N N Y O Y

Y = YES, N = NO, O = OPTIONAL

1. At least one of the following amplifiers is required for MNS operation as well as EVAC: FIK-DUAL50W, FIK-50, FIK-125 or FIK-INT50W.

Table 2.2 NFPA Requirements for FCP-2100ECS

16 FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Section 3: Before You Begin Installation

This section of the manual is intended to help you plan your tasks to facilitate a smooth installation. Please read this section thoroughly, espe-

cially if you are installing a FCP-2100 panel for the first time.

3.1 Inventory

When the FCP-2100 shipment is received, check that all the parts have been included in the shipment. The shipment consist of one of each of

the following:

• main circuit board with display

• backbox with door.

• plastic bag containing two keys, screws, cables, and ten 4.7K ohm end-of-line resistors

• manual

3.2 Environmental Specifications

It is important to protect the FCP-2100 control panel from water. To prevent water damage, the following precautions should be FOL-

LOWED when installing the units:

• Intended for indoor use in dry locations only

• Do not mount directly on exterior walls, especially masonry walls (condensation)

• Do not mount directly on exterior walls below grade (condensation)

• Protect from plumbing leaks

• Protect from splash caused by sprinkler system inspection ports

• Do not mount in areas with humidity-generating equipment (such as dryers, production machinery)

When selecting a location to mount the FCP-2100 control panel, the unit should be mounted where it will NOT be exposed to: temperatures

outside the range of 0°C- 49°C (32°F-120°F) or humidity exceeding 93% noncondensing.

3.3 Software Downloads

In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades

to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that

you download the most current version of software for each product prior to commissioning any system. Contact Technical Support with any

questions about software and the appropriate version for a specific application. Software updates can be found at www.fike.com.

3.4 Electrical Specifications

Table 3.1 lists the terminal block on the FCP-2100 as well as a description of each individual terminal and their respective electrical rating.

Terminal Label Description Rating Earth Ground

Faults

Voltage Current

BAC input (hot) 120/240 VAC, 50/60 Hz 4.5A for the FCP-2100, FCP-

2100ECS

2.8A for the FCP-2100HV

FCP-2100ECSHV

N/A

G Earth ground N/A N/A N/A

WAC input (neutral) 120/240 VAC, 50/60 Hz 4.5A for the FCP-2100, FCP-

2100ECS

2.8A FCP-2100HV

FCP-2100ECSHV

N/A

X *I/O 1 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X*I/O 2 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X *I/O 3 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X*I/O 4 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

Table 3.1 Terminal Descriptions and Electrical Specifications

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 17

Electrical Specifications Before You Begin Installation

X *I/O 5 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X*I/O 6 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X *I/O 7 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

X*I/O 8 Flexput Circuits 24 VDC 3.0 A notification and auxiliary

power circuits 0Ω

O100 mA for initiation circuits

B SBUS1 OUT SBUS communication 5 VDC 100 mA 0Ω

+ SBUS power 24 VDC 1.0 A

BSBUS1 IN Used for Class A installations 0Ω

B SBUS2 OUT SBUS communication 5 VDC 100 mA 0Ω

+ SBUS power 24 VDC 1.0 A

BSBUS2 IN Used for Class A installations 0Ω

N.C. RELAY 1 General Purpose Relay 1 24 VDC 2.5 A, resistive N/A

N.O.

N.C. RELAY 2 General Purpose Relay 2 24 VDC 2.5 A, resistive N/A

N.O.

N.C. TROUBLE Trouble Relay 24 VDC 2.5 A, resistive N/A

N.O.

S- SLC OUT SLC terminals 32 VDC 150 mA 0Ω

S+

SC- SLC IN Used for Class A installations 0Ω

SC+

Ring Phone Line 1 Telco Ring N/A 0Ω

Tip Phone Line 1 Telco Tip

Ring Phone Line 1 Premises Ring

Tip Phone Line 1 Premises Tip

Ring Phone Line 2 Telco Ring N/A 0Ω

Tip Phone Line 2 Telco Tip

Ring Phone Line 2 Premises Ring

Tip Phone Line 2 Premises Tip

Terminal Label Description Rating Earth Ground

Faults

Voltage Current

Table 3.1 Terminal Descriptions and Electrical Specifications

18 FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Before You Begin Installation Wiring Specifications

*Regulated for NAC circuits, special application when used for releasing or auxiliary power circuits

3.5 Wiring Specifications

Induced noise (transfer of electrical energy from one wire to another) can interfere with telephone communication or cause false alarms. To

avoid induced noise, follow these guidelines:

• Isolate input wiring from high current output and power wiring. Do not pull one multi-conductor cable for the entire panel. Instead,

separate the wiring as follows:

• Do not pull wires from different groups through the same conduit. If you must run them together, do so for as short a distance as

possible or use shielded cable. Connect the shield to earth ground at the panel. You must route high and low voltages separately.

• Route the wiring around the inside perimeter of the cabinet. It should not cross the circuit board where it could induce noise into the

sensitive microelectronics or pick up unwanted RF noise from the high speed circuits. See Figure 3.2 for an example.

• High frequency noise, such as that produced by the inductive reactance of a speaker or bell, can also be reduced by running the wire

through ferrite shield beads or by wrapping it around a ferrite toroid.

+Battery Battery Connection 24 VDC 1.12 A N/A

–

P7 Data

Network Used for FIK-NIC 24 VDC 21 mA 0Ω

P8 Voice

Network Used For FIK-NVCM 24 VDC 59 mA 0Ω

Terminal Label Description Rating Earth Ground

Faults

Voltage Current

Table 3.1 Terminal Descriptions and Electrical Specifications

High voltage AC power terminal

SLC loops SLC In/Out Terminals

POTS reporting input/output Phone line circuits, Ring Tip Telco, Phone Terminals

Notification circuits I/01-I/08 Terminals

SBUS SBUS1 In/Out Terminals, SBUS 2 In/Out Terminals

Relay circuits Trouble, Relay 1, Relay 2 Terminals

FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021 19

Wiring Specifications Before You Begin Installation

Figure 3.2 Wire Routing Example for FCP-2100

Battery cables from

under aluminum housing.

SBUS1OUT

SBUS1 IN

SBUS2 OUT

SBUS2IN

NETWORK

REPEATER

GND

ENTER

BACK BACK

NEXT NEXT

ACK

DRILL

RESET

SILEN CE

789

*0#

BACK

SBUS1 O UT

SBUS1 IN

SBUS2 OUT

SBUS2 I N

–

ENTER

BACK BACK

NEXT NEXT

ACK

DRILL

RESET

SILENCE

789

*0#

BACK

EXT.COMM

Route all low voltage

wiring through any of

these knockouts.

Relay outputs AC power input

tophone

lines

SLC IN/OUT

SBUS Devices

Fire alarm power-limited circuits

are installed using types FPL,

FPLR, FPLP, or permitted cables,

provided these power-limited cable

conductors extending beyond the

jacket are separated bya minimum

of 0.25 in (6.35mm) or by a non-

conductive sleeve or non-

conductive barrier from all other

conductors.

Maintain 0.25”

spacing between

battery cables and

input wiring.

All circuits, except

battery cables and AC,

are power-limited.

Maintain 0.25” spacing

between power-limited

and non power-limited

circuits.

Separate high and low

voltage circuits.

red black

Figure 3.1 Wire Routing Example for FCP-2100

Relay outputs AC power input

tophone

lines

SLC IN/OUT

SBUS Devices

Fire alarm power-limited circuits

are installed using types FPL,

FPLR, FPLP, or permitted cables,

provided these power-limitedcable

conductors extending beyond the

jacket are separated by a minimum

of 0.25 in (6.35mm) or by a non-

conductive sleeve or non-

conductive barrier from all other

conductors.

Maintain 0.25”

spacing between

battery cables and

input wiring.

All circuits, except

battery cables and AC,

are power-limited.

Maintain 0.25” spacing

between power-limited

and non power-limited

circuits.

Separate high and low

voltage circuits.

red

black

battery battery

20 FCP-2100/FCP-2100ECS Manual — P/N LS10143-002FK-E:A 3/11/2021

Before You Begin Installation Board Assembly Diagram

3.6 Board Assembly Diagram

Figure 3.3 Model FCP-2100

Assembly

Figure 3.3 shows the circuit boards, metal housing and annunciator that attach the FCP-2100 assembly to the cabinet. If you should need to

remove the board assembly for repair, remove the four mounting nuts which hold the assembly in the cabinet. Then, lift the entire assembly

out of the cabinet. Do not attempt to remove the circuit boards from the metal bracket.

Chassis

Mounting

Nuts

Onboard Annunciator

Trouble

Relay

Phone lines

SLC

In/Out

Battery

Connections

Data USB Port

Ethernet

Port

(non-power

limited)

Programmable

Alarm Relay

SBUS In

SBUS Out

Flexput

Circuits

Network

Voice

Network

Communication

This manual suits for next models

Table of contents

Other Fike Control Panel manuals

Fike

Fike TWINFLEXpro User manual

Fike

Fike Quadnet User manual

Fike

Fike GB2426367 User manual

Fike

Fike TWINFLEXpro User manual

Fike

Fike Twinflex pro2 User manual

Fike

Fike FCP-2100ECS User manual

Fike

Fike CIE-A-200 User manual

Fike

Fike SITA200plus User manual

Fike

Fike FCP-300 User manual

Fike

Fike FIK-RA2000 Technical manual

Fike

Fike FIK-RA100BD Technical manual

Fike

Fike FCP-75 User manual

Fike

Fike FCP-75 User manual

Fike

Fike TWINFLEX SRP 100-0001 User manual

Fike

Fike FIK-5496 User manual

Popular Control Panel manuals by other brands

wallas

wallas PI Thermo Operation guide

BFT

BFT THALIA BT A80 installation manual

Bestherm

Bestherm Selene HE10EBA instruction manual

Milestone pro

Milestone pro MP-WP6-IP user manual

ArtiVisuals

ArtiVisuals Mix-iT.ATEM user guide

Sony

Sony RCP-1500 Operation manual

Symetrix

Symetrix ARC-3 quick start guide

Cebora

Cebora 208.00 instruction manual

Menvier Security

Menvier Security TS690 Installation & programming manual

Johnson Controls

Johnson Controls IQ Panel user guide

Garmin

Garmin Volvo Penta Glass Cockpit B7 owner's manual

Schenck process

Schenck process Disomat Opus operating manual

Johnson Controls

Johnson Controls Bentel Security tyco ABSOLUTA Plus Installer manual

Satel

Satel Integra Series Installer manual

Honeywell

Honeywell Galaxy Dimension series Integration guide

LG PRCKD20E owner's manual

Nortek

Nortek 2GIG GC3E-345-K1 user guide

tau

tau K122M installation guide

Fike FCP-2100 User manual

Popular Control Panel manuals by other brands