Fike Fcp-75 User manual

P/N LS10147-003FK-E:A • ECN 151526

Document LS10147-003FK-E

3/17/2021 Rev:

Addressable Fire Alarm Control Panel

FCP-75

Instruction Manual

2FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Fire Alarm & Emergency Communication System Limitations

While a life safety system may lower insurance rates, it is not a substitute for life and property insurance!

An automatic fire alarm system—typically made up of smoke

detectors, heat detectors, manual pull stations, audible warning

devices, and a fire alarm control panel (FACP) with remote

notification capability—can provide early warning of a developing fire.

Such a system, however, does not assure protection against property

damage or loss of life resulting from a fire.

An emergency communication system—typically made up of an

automatic fire alarm system (as described above) and a life safety

communication system that may include an autonomous control unit

(ACU), local operating console (LOC), voice communication, and

other various interoperable communication methods—can broadcast

a mass notification message. Such a system, however, does not

assure protection against property damage or loss of life resulting

from a fire or life safety event.

The Manufacturer recommends that smoke and/or heat detectors be

located throughout a protected premises following the

recommendations of the current edition of the National Fire Protection

Association Standard 72 (NFPA 72), manufacturer's

recommendations, State and local codes, and the recommendations

contained in the Guide for Proper Use of System Smoke Detectors,

which is made available at no charge to all installing dealers. This

document can be found at http://www.systemsensor.com/appguides/.

A study by the Federal Emergency ManagementAgency (an agency

of the United States government) indicated thatsmoke detectors may

not go off in as many as 35% of all fires. While fire alarm systems are

designed to provide early warning against fire, they do not guarantee

warning or protection against fire. A fire alarm system may not

provide timely or adequate warning, or simply may not function, for a

variety of reasons:

Smoke detectors may not sense fire where smoke cannot reach the

detectors such as in chimneys, in or behind walls, on roofs, or on the

other side of closed doors.Smoke detectors alsomay not sense a fire

on another level or floor of a building. A second-floor detector, for

example, may not sense a first-floor or basement fire.

Particles of combustion or “smoke” from a developing fire may not

reach the sensing chambers of smoke detectors because:

• Barriers such as closed or partially closed doors, walls, chimneys,

even wet or humid areas may inhibit particle or smoke flow.

• Smoke particles may become “cold,” stratify, and not reach the

ceiling or upper walls where detectors are located.

• Smoke particles may be blown away from detectors by air outlets,

such as air conditioning vents.

• Smoke particles may be drawn into air returns before reaching the

detector.

The amount of “smoke” present may be insufficient to alarm smoke

detectors. Smoke detectors are designed to alarm at various levels of

smoke density. If such density levels are not created by a developing

fire at the location of detectors, the detectors will not go into alarm.

Smoke detectors, even when working properly, have sensing

limitations. Detectors that have photoelectronic sensing chambers

tend to detect smoldering fires better than flaming fires, which have

little visible smoke. Detectors that have ionizing-type sensing

chambers tend to detect fast-flaming fires better than smoldering

fires. Because fires develop in different ways and are often

unpredictable in their growth, neither type of detector is necessarily

best and a given type of detector may not provide adequate warning

of a fire.

Smoke detectors cannot be expected to provide adequate warning of

fires caused by arson, children playing with matches (especially in

bedrooms), smoking in bed, and violent explosions (caused by

escaping gas, improper storage of flammable materials, etc.).

Heat detectors do not sense particles of combustion and alarm only

when heat on their sensors increases at a predetermined rate or

reaches a predetermined level. Rate-of-rise heat detectors may be

subject to reduced sensitivity over time. For this reason, the rate-of-

rise feature of each detector should be tested at least once per year

by a qualified fire protection specialist. Heat detectors are designed to

protect property, not life.

IMPORTANT! Smoke detectors must be installed in the same room

as the control panel and in rooms used by the system for the

connection of alarm transmission wiring, communications, signaling,

and/or power. If detectors are not so located, a developing fire may

damage the alarm system, compromising its ability to report a fire.

Audible warning devices such as bells, horns, strobes, speakers

and displays may not alert people if these devices are located on the

other side of closed or partly open doors or are located on another

floor of a building. Any warning device may fail to alert people with a

disability or those who have recently consumed drugs, alcohol, or

medication. Please note that:

• An emergency communication system may take priority over a fire

alarm system in the event of a life safety emergency.

• Voice messaging systems must be designed to meet intelligibility

requirements as defined by NFPA, local codes, andAuthorities

Having Jurisdiction (AHJ).

• Language and instructional requirements must be clearly dissemi-

nated on any local displays.

• Strobes can, under certain circumstances, cause seizures in peo-

ple with conditions such as epilepsy.

• Studies have shown that certain people, even when they hear a

fire alarm signal, do not respond to or comprehend the meaning of

the signal.Audible devices, such as horns and bells, can have dif-

ferent tonal patterns and frequencies. It is the property owner's

responsibility to conduct fire drills and other training exercises to

make people aware of fire alarm signals and instruct them on the

proper reaction to alarm signals.

• In rare instances, the sounding of a warning device can cause

temporary or permanent hearing loss.

A life safety system will not operate without any electrical power. If

AC power fails, the system will operate from standby batteries only for

a specified time and only if the batteries have been properly

maintained and replaced regularly.

Equipment used in the system may not be technically compatible

with the control panel. It is essential to use only equipment listed for

service with your control panel.

Alarm Signaling Communications:

•IP connections rely on available bandwidth, which could be lim-

ited if the network is shared by multiple users or if ISP policies

impose restrictions on the amount of data transmitted. Service

packages must be carefully chosen to ensure that alarm signals

will always have available bandwidth. Outages by the ISP for

maintenance and upgrades may also inhibit alarm signals. For

added protection, a backup cellular connection is recommended.

•Cellular connections rely on a strong signal. Signal strength can

be adversely affected by the network coverage of the cellular car-

rier, objects and structural barriers at the installation location. Uti-

lize a cellular carrier that has reliable network coverage where the

alarm system is installed. For added protection, utilize an external

antenna to boost the signal.

•Telephone lines needed to transmit alarm signals from a premise

to a central monitoring station may be out of service or temporarily

disabled. For added protection against telephone line failure,

backup alarm signaling connections are recommended.

The most common cause of life safety system malfunction is

inadequate maintenance. To keep the entire life safety system in

excellent working order, ongoing maintenance is required per the

manufacturer's recommendations, and UL and NFPA standards.At a

minimum, the requirements of NFPA 72 shall be followed.

Environments with large amounts of dust, dirt, or high air velocity

require more frequent maintenance.A maintenance agreement

should be arranged through the local manufacturer's representative.

Maintenance should be scheduled as required by National and/or

local fire codes and should be performed by authorized professional

life safety system installers only. Adequate written records of all

inspections should be kept. Limit-F-2020

FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021 3

Installation Precautions

Adherence to the following will aid in problem-free installation with long-term reliability:

WARNING - Several different sources of power can be con-

nected to the fire alarm control panel. Disconnect all sources of

power before servicing. Control unit and associated equipment may

be damaged by removing and/or inserting cards, modules, or inter-

connecting cables while the unit is energized. Do not attempt to

install, service, or operate this unit until manuals are read and under-

stood.

CAUTION - System Re-acceptance Test after Software Changes:

To ensure proper system operation, this product must be tested in

accordance with NFPA 72 after any programming operation or

change in site-specific software. Re-acceptance testing is required

after any change, addition or deletion of system components, or after

any modification, repair or adjustment to system hardware or wiring.

All components, circuits, system operations, or software functions

known to be affected by a change must be 100% tested. In addition,

to ensure that other operations are not inadvertently affected, at

least 10% of initiating devices that are not directly affected by the

change, up to a maximum of 50 devices, must also be tested and

proper system operation verified.

This system meets NFPA requirements for operation at 0-49º C/32-

120º F and at a relative humidity 93% ± 2% RH (non-condensing) at

32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's

standby batteries and the electronic components may be adversely

affected by extreme temperature ranges and humidity. Therefore, it

is recommended that this system and its peripherals be installed in

an environment with a normal room temperature of 15-27º C/60-80º

Verify that wire sizes are adequate for all initiating and indicating

device loops. Most devices cannot tolerate more than a 10% I.R.

drop from the specified device voltage.

Like all solid state electronic devices, this system may operate

erratically or can be damaged when subjected to lightning induced

transients.Although no system is completely immune from lightning

transients and interference, proper grounding will reduce susceptibil-

ity. Overhead or outside aerial wiring is not recommended, due to an

increased susceptibility to nearby lightning strikes. Consult with the

Technical Services Department if any problems are anticipated or

encountered.

Disconnect AC power and batteries prior to removing or inserting

circuit boards. Failure to do so can damage circuits.

Remove all electronic assemblies prior to any drilling, filing, ream-

ing, or punching of the enclosure. When possible, make all cable

entries from the sides or rear. Before making modifications, verify

that they will not interfere with battery, transformer, or printed circuit

board location.

Do not tighten screw terminals more than 9 in-lbs. Over-tightening

may damage threads, resulting in reduced terminal contact pressure

and difficulty with screw terminal removal.

This system contains static-sensitive components. Always

ground yourself with a proper wrist strap before handling any circuits

so that static charges are removed from the body. Use static sup-

pressive packaging to protect electronic assemblies removed from

the unit.

Units with a touchscreen display should be cleaned with a dry,

clean, lint free/microfiber cloth. If additional cleaning is required,

apply a small amount of Isopropyl alcohol to the cloth and wipe

clean. Do not use detergents, solvents, or water for cleaning. Do not

spray liquid directly onto the display.

Follow the instructions in the installation, operating, and program-

ming manuals.These instructions must be followed to avoid damage

to the control panel and associated equipment. FACP operation and

reliability depend upon proper installation.

Precau-D2-11-2017

FCC Warning

WARNING: This equipment generates, uses, and can radi-

ate radio frequency energy and if not installed and used in

accordance with the instruction manual may cause interfer-

ence to radio communications. It has been tested and found

to comply with the limits for classA computing devices pur-

suant to Subpart B of Part 15 of FCC Rules, which is

designed to provide reasonable protection against such

interference when devices are operated in a commercial

environment. Operation of this equipment in a residential

area is likely to cause interference, in which case the user

will be required to correct the interference at his or her own

expense.

Canadian Requirements

This digital apparatus does not exceed the ClassA limits for

radiation noise emissions from digital apparatus set out in

the Radio Interference Regulations of the Canadian Depart-

ment of Communications.

Le present appareil numerique n'emet pas de bruits radio-

electriques depassant les limites applicables aux appareils

numeriques de la classeAprescrites dans le Reglement sur

le brouillage radioelectrique edicte par le ministere des

Communications du Canada.

eVance®, Flexput®, Honeywell®, JumpStart®, and SWIFT® are registered trademarks of Honeywell International Inc. Microsoft® and Windows® are registered

trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered trademark of The Mozilla Foundation.

4FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Software Downloads

In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent

upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly

recommend that you download the most current version of software for each product prior to commissioning any system. Contact

Technical Support with any questions about software and the appropriate version for a specific application.

Documentation Feedback

Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions about our online

Help or printed manuals, you can email us.

Please include the following information:

• Product name and version number (if applicable)

• Printed manual or online Help

• Topic Title (for online Help)

• Page number (for printed manual)

• Brief description of content you think should be improved or corrected

• Your suggestion for how to correct/improve documentation

Send email messages to:

[email protected]

or call (800)979-3453, x21 in US or (816)229-3405 international

This symbol (shown left) on the product(s) and / or accompanying documents means that used electrical and electronic products

should not be mixed with general household waste. For proper treatment, recovery and recycling, contact your local authorities or

dealer and ask for the correct method of disposal.

Electrical and electronic equipment contains materials, parts and substances, which can be dangerous to the environment and harmful

to human health if the waste of electrical and electronic equipment (WEEE) is not disposed of correctly.

FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021 5

Table of Contents

Section 1: Introduction ................................................................................................................................................... 10

1.1: Overview of Basic System...............................................................................................................................................................................10

1.1.1: Hardware Features................................................................................................................................................................................10

1.1.2: Network System Hardware Features ....................................................................................................................................................10

1.1.3: Software Features .................................................................................................................................................................................10

1.2: About this Manual............................................................................................................................................................................................10

1.2.1: Terms Used in this Manual...................................................................................................................................................................10

1.3: Compatible Products........................................................................................................................................................................................11

Section 2: Agency Listings, Approvals, and Requirements........................................................................................ 12

2.1: Federal Communications Commission (FCC).................................................................................................................................................12

2.2: Underwriters Laboratories (UL)......................................................................................................................................................................13

2.2.1: Requirements for All Installations........................................................................................................................................................13

Restricted Options: .................................................................................................................................................................................13

2.2.2: Requirements for Central Station Fire Alarm Systems ........................................................................................................................13

2.2.3: Requirements for Local Protected Fire Alarm Systems .......................................................................................................................13

2.2.4: Requirements for Remote Station Protected Fire Alarm Systems........................................................................................................13

2.2.5: Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 720..................................13

2.2.6: NFPA Requirements.............................................................................................................................................................................14

Section 3: Before You Begin Installing ......................................................................................................................... 15

3.1: Inventory..........................................................................................................................................................................................................15

3.2: Environmental Specifications..........................................................................................................................................................................15

3.3: Software Downloads........................................................................................................................................................................................15

3.4: Electrical Specifications ..................................................................................................................................................................................15

3.5: Wiring Specifications.......................................................................................................................................................................................16

3.6: Board Assembly Diagram................................................................................................................................................................................17

3.7: Calculating Current Draw and Standby Battery ..............................................................................................................................................17

3.7.1: Current Draw Worksheet Requirements...............................................................................................................................................17

3.7.2: Current Draw Worksheet for Fike IDP SLC Devices ..........................................................................................................................18

Maximum Battery Standby Load............................................................................................................................................................20

Section 4: Control Panel Installation............................................................................................................................. 21

4.1: Mounting the Control Panel Cabinet...............................................................................................................................................................21

4.1.1: Preventing Water Damage....................................................................................................................................................................21

4.1.2: Removing the FCP-75 Assembly from the Housing............................................................................................................................21

4.2: AC Power Connection .....................................................................................................................................................................................21

4.3: Battery Power ..................................................................................................................................................................................................22

4.3.1: Battery Accessory Cabinet ...................................................................................................................................................................23

Installing the RBB Accessory Cabinet and Batteries .............................................................................................................................23

4.4: SBUS Wiring ...................................................................................................................................................................................................24

4.4.1: Calculating Wiring distance for SBUS modules ..................................................................................................................................24

4.4.2: Wiring Configurations..........................................................................................................................................................................26

4.5: FIK-RA100 Remote Annunciator Installation.................................................................................................................................................26

4.5.1: Mounting the FIK-RA100 ....................................................................................................................................................................27

Flush Mounting.......................................................................................................................................................................................27

Surface Mounting ...................................................................................................................................................................................29

4.5.2: FIK-RA100 Connection to the Panel....................................................................................................................................................30

4.6: FIK-RA1000R Remote Annunciator Installation............................................................................................................................................30

4.6.1: Mounting the FIK-RA1000R................................................................................................................................................................31

Flush Mounting.......................................................................................................................................................................................31

Surface Mounting ...................................................................................................................................................................................32

4.7: FIK-RA2000 Remote Annunciator Installation...............................................................................................................................................33

4.7.1: Mounting the FIK-RA2000 ..................................................................................................................................................................33

Flush Mounting.......................................................................................................................................................................................33

Surface Mounting ...................................................................................................................................................................................35

4.7.2: FIK-RA2000 Connection to the Panel..................................................................................................................................................36

4.8: FIK-5824 Serial/Parallel Printer Interface Module Installation ......................................................................................................................36

4.8.1: Selecting FIK-5824 Options.................................................................................................................................................................37

4.9: FIK-5880 LED Driver Module........................................................................................................................................................................37

4.9.1: FIK-5880 Board Layout .......................................................................................................................................................................38

4.9.2: FACP Connection.................................................................................................................................................................................38

6FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Table of Contents

4.9.3: LED Wiring..........................................................................................................................................................................................38

4.9.4: Dry Contact Wiring ..............................................................................................................................................................................39

4.10: FIK-5865-3 / FIK-5865-4 LED Annunciator Installation .............................................................................................................................40

4.10.1: FACP Connection...............................................................................................................................................................................41

4.10.2: FIK-5865 Mounting............................................................................................................................................................................41

4.11: Configuring Modules.....................................................................................................................................................................................42

4.11.1: Assigning Module IDs........................................................................................................................................................................42

4.12: Telephone Connection ...................................................................................................................................................................................43

4.13: Notification Appliance/Auxiliary Power Circuits .........................................................................................................................................43

4.13.1: Conventional Notification Appliance.................................................................................................................................................43

Class B Notification Wiring ...................................................................................................................................................................43

Class A Notification Wiring ...................................................................................................................................................................44

4.13.2: Auxiliary Power Installation...............................................................................................................................................................44

Door Holder Power.................................................................................................................................................................................44

Constant Power.......................................................................................................................................................................................45

Resettable Power.....................................................................................................................................................................................45

Sounder Sync Power...............................................................................................................................................................................45

4.14: On-Board Relays (Conventional) ..................................................................................................................................................................45

4.14.1: Common Trouble Relay .....................................................................................................................................................................45

4.14.2: Programmable Relays.........................................................................................................................................................................45

4.15: Remote Station Applications .........................................................................................................................................................................46

4.15.1: Keltron Model 3158 Installation.........................................................................................................................................................46

4.15.2: City Box Connection Using the 5220 Module ...................................................................................................................................46

4.15.3: NFPA 72 Polarity Reversal ................................................................................................................................................................47

Using the 5220 Module...........................................................................................................................................................................47

4.15.4: Using a MR-201/T Control Relay From Air Products .......................................................................................................................48

4.15.5: Transmitter Activated by Dry Contacts..............................................................................................................................................50

Section 5: Networking Common Communicator List .................................................................................................. 51

5.1: Network System Hardware Features ...............................................................................................................................................................51

5.1.1: Networked Panels.................................................................................................................................................................................51

5.1.2: Wiring Options to Connect Networked Panels.....................................................................................................................................51

5.2: Direct Connect Wiring Option.........................................................................................................................................................................51

5.3: FIK-NIC Wiring Options.................................................................................................................................................................................51

5.3.1: Fiber Loop Modules .............................................................................................................................................................................52

FIK-NIC-KIT Mounting Kit...................................................................................................................................................................53

5.3.2: FIK-NIC Installation.............................................................................................................................................................................53

Unshielded Twisted Pair Wiring between Multiple Panels....................................................................................................................54

Fiber Optic Multi-Mode Wiring between Multiple Panels.....................................................................................................................55

Fiber Optic and Twisted Pair Wiring between Multiple Panels .............................................................................................................57

5.4: Setting the Panel ID for each Panel Network ..................................................................................................................................................58

Section 6: Network Management................................................................................................................................... 59

6.1: Network Diagnostics .......................................................................................................................................................................................59

6.1.1: Ping Panel.............................................................................................................................................................................................59

6.1.2: Data Network Status.............................................................................................................................................................................59

6.2: Network Programming ....................................................................................................................................................................................59

6.2.1: Learn Network......................................................................................................................................................................................59

6.2.2: Edit Network Names.............................................................................................................................................................................59

6.2.3: Edit Panel ID.........................................................................................................................................................................................59

6.2.4: Computer Access..................................................................................................................................................................................60

6.2.5: Access Codes........................................................................................................................................................................................60

Edit Name ...............................................................................................................................................................................................61

Edit Access Code....................................................................................................................................................................................61

Panel Functions.......................................................................................................................................................................................61

6.2.6: Communicator Options.........................................................................................................................................................................61

Communicator Assignments...................................................................................................................................................................61

Communicator Miscellaneous ................................................................................................................................................................61

Receiver Configuration...........................................................................................................................................................................61

Communicator Reporting Table .............................................................................................................................................................62

6.3: Sync Network Options.....................................................................................................................................................................................62

6.4: Network Management Quick Reference .........................................................................................................................................................63

FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021 7

Table of Contents

Section 7: Fike IDP and SWIFT SLC Device Installation.............................................................................................. 65

7.1: List of Fike IDP SLC Devices.........................................................................................................................................................................65

7.2: SWIFT Wireless SLC Devices ........................................................................................................................................................................65

7.3: Maximum Number of Devices ........................................................................................................................................................................65

7.4: Wiring Requirements for SLC Devices...........................................................................................................................................................66

7.4.1: Wire Sizing for Internal SLC................................................................................................................................................................66

7.4.2: Wiring Requirements for IDP Modules................................................................................................................................................66

7.4.3: Wiring SLC in Class A Configuration..................................................................................................................................................67

7.5: Addressing IDP SLC Devices..........................................................................................................................................................................68

7.6: Wiring the FIK-W-WGI...................................................................................................................................................................................68

7.6.1: SLC Connections..................................................................................................................................................................................68

Section 8: Programming Overview................................................................................................................................ 69

8.1: JumpStart AutoProgramming ..........................................................................................................................................................................69

8.1.1: Input Points...........................................................................................................................................................................................69

8.1.2: Output Points ........................................................................................................................................................................................69

8.1.3: Running JumpStart AutoProgramming ................................................................................................................................................69

8.2: Mapping Overview ..........................................................................................................................................................................................70

8.2.1: Input Point Mapping.............................................................................................................................................................................70

8.2.2: Output Circuit Mapping........................................................................................................................................................................72

8.2.3: Event Mapping.....................................................................................................................................................................................72

8.2.4: Mapping LED Points............................................................................................................................................................................75

8.3: Programming Using the HFSS Programming Tool .........................................................................................................................................75

8.4: Programming Using an Annunciator ...............................................................................................................................................................75

8.4.1: Entering / Exiting the Program Menu..................................................................................................................................................76

8.4.2: Moving through the Menus ..................................................................................................................................................................76

8.4.3: Selecting Options and Entering Data....................................................................................................................................................76

8.5: Programming Menu Quick Reference.............................................................................................................................................................77

Section 9: Programming................................................................................................................................................. 84

9.1: UL 864 Programming Requirements...............................................................................................................................................................84

9.2: Modules ...........................................................................................................................................................................................................84

9.2.1: Edit Modules.........................................................................................................................................................................................84

Editing Module ID..................................................................................................................................................................................84

Naming Modules.....................................................................................................................................................................................84

Changing Module Options......................................................................................................................................................................85

9.2.2: Adding a Module..................................................................................................................................................................................85

9.2.3: Deleting a Module ................................................................................................................................................................................85

9.2.4: View Module List.................................................................................................................................................................................85

9.3: Zone.................................................................................................................................................................................................................85

9.3.1: Edit Zone ..............................................................................................................................................................................................85

Edit Zone Name......................................................................................................................................................................................86

Edit Zone Properties ...............................................................................................................................................................................86

Zone Accessory Options.........................................................................................................................................................................87

9.3.2: View Zone Points .................................................................................................................................................................................87

9.4: Group...............................................................................................................................................................................................................88

9.4.1: Edit Group ............................................................................................................................................................................................88

Edit Group Name....................................................................................................................................................................................88

Edit Group Properties .............................................................................................................................................................................88

9.4.2: View Group Points ...............................................................................................................................................................................88

9.4.3: Edit OPG Template...............................................................................................................................................................................89

9.5: Point.................................................................................................................................................................................................................89

9.5.1: Point Programming For SLC................................................................................................................................................................89

9.5.2: Point Programming for the Internal or External Power Module ..........................................................................................................91

9.5.3: Point Programming For FIK-5880 and FIK-5865 Modules.................................................................................................................92

9.6: System Options................................................................................................................................................................................................93

9.6.1: Communication Options.......................................................................................................................................................................93

Auto Test Time.......................................................................................................................................................................................93

Phone Lines.............................................................................................................................................................................................93

Edit Ethernet ...........................................................................................................................................................................................94

AlarmNet Timers....................................................................................................................................................................................95

Phone Line Gains....................................................................................................................................................................................95

9.6.2: Daytime/Nighttime Sensitivity.............................................................................................................................................................95

8FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Table of Contents

9.6.3: Holiday Days ........................................................................................................................................................................................96

9.6.4: Time Options ........................................................................................................................................................................................96

Water Flow Delay...................................................................................................................................................................................96

Alarm Verify...........................................................................................................................................................................................97

AC Report Delay ....................................................................................................................................................................................97

AC Line Frequency.................................................................................................................................................................................97

Clock Display Format (AM/PM or Military) .........................................................................................................................................97

Auto-Resound (4 or 24 hours)................................................................................................................................................................97

9.6.5: Miscellaneous Options..........................................................................................................................................................................97

Strobes Active when Silenced ................................................................................................................................................................98

Auto Display Events...............................................................................................................................................................................98

9.6.6: Daylight Saving Options.......................................................................................................................................................................98

Automatic Daylight Saving Adjustment.................................................................................................................................................98

Daylight Saving Time Start and End......................................................................................................................................................98

9.6.7: Edit Banner...........................................................................................................................................................................................98

9.6.8: SLC Family...........................................................................................................................................................................................99

9.7: JumpStart Autoprogramming...........................................................................................................................................................................99

9.8: Restore Defaults...............................................................................................................................................................................................99

Section 10: System Operation...................................................................................................................................... 100

10.1: User and Installer Default Codes:................................................................................................................................................................100

10.2: Annunciator Description..............................................................................................................................................................................100

10.2.1: LCD Display.....................................................................................................................................................................................100

10.2.2: Banner...............................................................................................................................................................................................100

10.2.3: Single Key Acknowledge .................................................................................................................................................................100

10.3: Menu System ...............................................................................................................................................................................................101

10.3.1: Main Menu Overview.......................................................................................................................................................................101

10.3.2: Using the Menus...............................................................................................................................................................................101

10.4: Basic Operation ...........................................................................................................................................................................................101

10.4.1: Setting Time and Date ......................................................................................................................................................................101

10.4.2: Disable / Enable a Point....................................................................................................................................................................101

Disable / Enable NACs by Template....................................................................................................................................................101

Disable / Enable NACs by Group.........................................................................................................................................................101

Disable / Enable Zone Points................................................................................................................................................................101

Disable / Enable Point...........................................................................................................................................................................101

Inhibit Output Group ............................................................................................................................................................................101

10.4.3: View Event History ..........................................................................................................................................................................102

To clear the event history......................................................................................................................................................................102

10.4.4: Conduct a Fire Drill..........................................................................................................................................................................102

10.4.5: Conduct an Indicator Test.................................................................................................................................................................102

10.4.6: Conduct a Walk Test ........................................................................................................................................................................102

10.4.7: Conduct a Communicator Test.........................................................................................................................................................102

10.4.8: Manual AlarmNet Registration.........................................................................................................................................................103

10.4.9: Silence Alarms or Troubles ..............................................................................................................................................................103

10.4.10: Reset alarms....................................................................................................................................................................................103

Reset Communicator............................................................................................................................................................................103

10.4.11: Check Detector Sensitivity Through Point Status..........................................................................................................................103

10.4.12: View Status of a Point ....................................................................................................................................................................104

10.4.13: View Alarms, Supervisories or Troubles........................................................................................................................................104

10.4.14: View System Information...............................................................................................................................................................104

10.5: Operation Mode Behavior ...........................................................................................................................................................................105

10.6: Operation Mode Behavior ...........................................................................................................................................................................106

10.6.1: Multi-Site Annunciator and Multi-Site User Access........................................................................................................................108

10.7: Releasing Operations...................................................................................................................................................................................108

10.7.1: Single Interlock Zone Releasing.......................................................................................................................................................109

10.7.2: Double Interlock Zone Releasing .....................................................................................................................................................110

10.8: Smoke Alarm Verification ...........................................................................................................................................................................110

10.9: Function Keys.............................................................................................................................................................................................111

10.9.1: Recording an F-Key Macro ..............................................................................................................................................................111

10.9.2: Aborting an F-Key Macro Recording Session..................................................................................................................................111

10.9.3: Erasing an F-Key Macro...................................................................................................................................................................111

10.9.4: Using a Recorded F-Key Macro.......................................................................................................................................................111

FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021 9

Table of Contents

10.9.5: F-Key Status Event...........................................................................................................................................................................111

10.9.6: F-Key Map Inhibit............................................................................................................................................................................111

Section 11: Reporting ................................................................................................................................................... 112

11.1: Receivers Compatible with the Control Panel.............................................................................................................................................112

11.2: SIA / FCP-75 Panels PI Modifier Reporting: ..............................................................................................................................................119

11.3: SIA– FCP-75 Panel Communicator:............................................................................................................................................................120

Section 12: Testing and Troubleshooting................................................................................................................... 122

12.1: Troubleshooting...........................................................................................................................................................................................122

Table 12.1: Common Problems.............................................................................................................................................................................122

12.1.1: Periodic Testing And Maintenance ..................................................................................................................................................122

12.1.2: Event History....................................................................................................................................................................................123

12.2: Built-in Troubleshooting and Testing Tools ................................................................................................................................................123

12.2.1: SLC Device Locater .........................................................................................................................................................................123

12.2.2: SLC Multi Locater............................................................................................................................................................................123

12.2.3: I/O Point Control ..............................................................................................................................................................................124

12.3: Earth Fault Resistance .................................................................................................................................................................................124

Section 13: Installation Records.................................................................................................................................. 125

13.1: IDP SLC Device Point Record ....................................................................................................................................................................125

Appendix A: Compatible Devices ................................................................................................................................ 127

A.1: Notification Appliances ................................................................................................................................................................................127

A.2: Four Wire Smoke Detectors/Devices (UL Listed)........................................................................................................................................136

A.3: Door Holders (UL Listed).............................................................................................................................................................................137

A.4: Relays (UL Listed)........................................................................................................................................................................................137

A.5: Compatible 520Hz Signaling Speakers ........................................................................................................................................................138

A.6: Compatible 520Hz Low Frequency Bases....................................................................................................................................................138

Appendix B: Editing Text Using the Built-In Programmer......................................................................................... 139

B.1: Characters Used for Editing Text..................................................................................................................................................................139

B.2: Example Name Edit ......................................................................................................................................................................................139

Appendix C: Expanded Receiver/Panel Relationship................................................................................................ 140

Appendix D: Cadence Patterns.................................................................................................................................... 141

Appendix E: Panel Security.......................................................................................................................................... 142

Model FCP-75 Basic Operating Instructions............................................................................................................... 143

10 FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Section 1: Introduction

The FCP-75 Fire Alarm Control / Communicator is an Addressable Fire Alarm Control System that meets the requirements of UL 864.

1.1 Overview of Basic System

1.1.1 Hardware Features

• The FCP-75 has one built in signaling line circuit (SLC) that supports 75 IDP detectors and 75 IDP modules.

• The FCP-75 is capable of outputting 2.5A of output power during an alarm activation through 2 sets of terminals for the notification

appliance circuits or an auxiliary application. Each circuit is power-limited per UL 864 and can source up to 2.5A during an alarm

activation. The constant auxiliary power load must not exceed 1A for normal standby.

• Built-in dual phone line, digital alarm communicator/transmitter (DACT), or IP technologies.

• Reports events to central station by point or by zone.

• UL Listed for pre-action and deluge releasing systems.

• Two general purpose Form C programmable relays.

• One Form C Trouble Relay.

• Basic system operation can be performed from the on-board, or any remote annunciator.

• Up to 20 user profiles can be programmed, each having custom Access Code, and Main Menu items.

• Can be used with any combination of up to 8 Model FIK-RA100, FIK-RA1000R, or FIK-RA2000 Remote LCD Annunciators (sold

separately).

• Can be used with Model FIK-5865-3, FIK-5865-4, and FIK-5880 in any combination for a total of eight devices on one control panel.

See Figure 4.29 and Figure 4.32 for additional information on these models.

• Printing of event log available through the Model FIK-5824 serial/parallel printer interface module.

• 125 software zones, 125 Output Groups.

• Add four Notification/Auxiliary power circuits with each FIK-5496 NAC Expander. See note below.

1.1.2 Network System Hardware Features

• The default network setup can contain up to 32- FCP-75 panels connected.

• Network support for up to 32 Sites.

• Each building is referred to as a “site”.

• Panels can be interconnected using CLASS B or CLASS A topology.

• Use the FIK-NIC Network Interface Card to create a network. Copper wire or fiber optic cable panel connectivity can be used within

the same networked system.

• The network architecture provides true peer to peer capability allowing network survivability for all hardware that remains operational

in the event of partial system failure.

1.1.3 Software Features

• Advanced smoke detector features:

– Automatic drift compensation

– Maintenance alert region

– Point status meets calibrated smoke test requirements for NFPA 72

• “JumpStart” feature for easy programming

• Non-volatile event history stores 1000 events

• A choice of output patterns available for notification outputs, including Temp 4 along with ANSI 3.41 temporal signal

• Built-in synchronization appliance support forAMSECO, Gentex®, Wheelock®, or System Sensor ®

1.2 About this Manual

This manual is intended to be a complete reference for all installation and operation tasks for the FCP-75. Please let us know if the manual

does not meet your needs in any way. We value your feedback!

1.2.1 Terms Used in this Manual

The following terminology is used with the FCP-75 system:

NOTE: Total output power for both circuits must not exceed 2.5A in alarm condition, and total output power for both circuits must not exceed

1.0A for all other activation conditions (i.e. Supervisory, Trouble, etc.).

NOTE: The system can support a maximum of eight intelligent power modules, either the FIK-RPS1000 or FIK-5496, in any combination.

Term Description

SLC Signaling Line Circuit

Module The term module is used for all hardware devices except for SLC addressable devices and notification

appliances. This includes the FCP-75 panel itself.

Input Point An addressable sensing device, such as a smoke or heat detector or a contact monitor device.

Input Zone A protected area made up of input points.

Table 1.1 Manual Terminology

Compatible Products Introduction

FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021 11

1.3 Compatible Products

The chart below lists the products available for use with the FCP-75.

Output Point (or Output Circuit) Anotification point or circuit for notification appliances. Relay circuits and auxiliary power circuits are also

considered output points.

Group (or “Output Group”) Agroup of output points. Operating characteristics are common to all output points in the group.

Output (or “Cadence”) Pattern The pattern that the output will use, for example, Constant, March Code, ANSI 3.41. Applies to zones

and special system events. See Appendix D for additional information.

Mapping Mapping is the process of specifying which outputs are activated when certain events occur in the

system. Figure 8.2 explains mapping in detail.

Network System Consist of any combination of 32 panels of these model numbers: FCP-75, FCP-300, FCP-300ECS,

FCP-2100 or FCP-2100ECS.

SWIFT Smart Wireless Integrated Fire Technology

Term Description

Table 1.1 Manual Terminology (Continued)

Type of Device Model Description

Fike IDP Addressable SLC

Devices See Section 7.1 for a list of compatible devices.

SWIFT Wireless SLC Devices See Section 7.2 for a list of compatible devices

Other Modules FIK-5824 Serial/Parallel

Printer Interface Module Allows a printer to be attached for the on-site event logging. Maximum of four FIK-5824s per

control panel.

FIK-RPS1000 Power

Supply Provides additional power, six Flexput circuits, and two Form C relays. Max 8 per system. See

FIK-RPS1000 Installation Manual (PN LS10259-001FK-E) for more information.

FIK-5496 NAC Expander Provides 4 additional Notification Appliance Circuits/Auxiliary power. (Up to 8 per FCP-75

system).

FIK-RA100 and

FIK-RA1000R LCD

Annunciator

4 x20 Remote LCD annunciator. can be used in any combination, up to a total of 8 devices on

one panel.

FIK-RA2000 LCD

Annunciator 4 x 40 Remote LCD annunciator can be used in any combination, up to a total of 8 devices on

one panel.

FIK-5865-3 and

FIK-5865-4 LED

Annunciator

LED annunciator can display up to 30 LEDs (15 red and 15 yellow). FIK-5865-4 has key

switches for silence and reset, and a system trouble LED. FIK-5865-3, FIK-5865-4, and FIK-

5880 can be used in any combination, up to a total of eight devices on one panel.

RA-100TR Trim Ring Trim ring kit for surface mounting the FIK-RA2000/FIK-RA1000R annunciators.

FIK-5880 LED Driver

Module Driver for up to 40 LEDs. Interfaces with customized annunciator boards. In addition the FIK-

5880 has eight generic switch input points.

FIK-5883 General

Purpose Relay Module Provides 10 Form C relays. Designed to be driven by the FIK-5880. Up to four, FIK-5883s can

be used with each FIK-5880 module.

FIK-NIC Network Interface Card

FIK-FML Fiber-Optic Multi Mode

FIK-FSL Fiber-Optic Single Mode

Wireless FIK-W-WGI Wireless Gateway

FIK-W-PHOTO Wireless Photoelectric Smoke Detector with 4" base

FIK-W-ACCLIMATE Wireless Multi criteria photoelectric smoke detector with thermal (135°F) with 4" base

FIK-W-HEAT-ROR Wireless heat, ROR/ 135° fixed with 4" base

FIK-W-HEAT Wireless Heat, 135° fixed with 4" base

FIK-W-MONITOR Wireless Addressable Monitor module

FIK-W-RELAY Wireless Addressable Relay module

B210W 6" wireless base

Misc. HFSS Programming Tool For communication and panel programming with a Windows-based computer. Enables remote

viewing of detector status and event history.

7860 Telephone Cord RJ31X cord for connecting phone line to the FCP-75.

7628 UL Listed End-of-line resistor

Table 1.2 FCP-75 Compatible Products

12 FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Section 2: Agency Listings, Approvals, and Requirements

Install and maintain in accordance with NFPA 72. Detector spacing shall be in accordance to NFPA 72. End-of -line relays and resistors shall

be placed within the electrical box located and the end of the initiating circuit. Testing and maintenance should be performed according to

NFPA 72.

2.1 Federal Communications Commission (FCC)

The following information must be provided to the telephone company before the FCP-75 can be connected to the phone lines:

1. This device may not be directly connected to coin telephone or party line services.

2. This device cannot be adjusted or repaired in the field. In case of trouble with the device, notify the installing company or return to:

Fike Corporation

704 SW 10th Street

Blue Springs, MO 61015

1+816-229-3405

3. If the FCP-75 causes harm to the telephone network, the telephone company will notify the user in advance that temporary

discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the user as soon as

possible. Users have the right to file complaints, if necessary, with the Federal Communications Commission.

4. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the

equipment. If this happens, the telephone company will provide advance notice to allow you to make the necessary modifications to

maintain uninterrupted service.

1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by theACTA. On the wiring diagram of this

equipment is a label that contains, among other information, a product identifier in the format US: HS9AL10A2100. If requested,

this number must be provided to the telephone company.

2. See manual for phone jack information.

3. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable

FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this

product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

4. The REN (ringer equivalence number) provided on this installation sheet is used to determine the number of devices that may be

connected to the public switched telephone network. This number must not exceed 5.0. Since this product has an REN of 1.0A, the

number of devices is limited. The REN number is embedded in the FCC registration number as 10A.

5. If this equipment FCP-75 causes harm to the telephone network, the telephone company will notify you in advance that temporary

discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as

soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

6. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of

the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary

modifications to maintain uninterrupted service.

7. If trouble is experienced with the FCP-75, for repair or warranty information, please contact technical support at (800)979-3453

or www.fike.com. If the equipment is causing harm to the telephone network, the telephone company may request that you

disconnect the FCP-75 until the problem has been resolved.

8. See warranty in back of this manual for repair and replacement information.

9. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or

corporation commission for information.

10. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this FCP-75 does not

disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or

qualified installer.

Electrical Safety Advisory:

Parties responsible for equipment requiringAC power should consider including an advisory notice in their customer information suggesting

the customer use a surge arrestor. Telephone companies report that electrical surges, typically lightning transients, are very destructive to

customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem.

A Manufacturer: Fike

B Model Number: FCP-75

C FCC registration number: US: HS9AL10A2100

Ringer equivalence: 1.0A

D Type of jack: RJ31X

E Facility Interface Codes: Loop Start: 02LS2

F Service Order Code: 9.0F

WARNING: FCC RULES PART 15

THIS DEVICE HAS BEEN VERIFIED TO COMPLY WITH FCC RULES PART 15. OPERATION IS SUBJECT TO THE

FOLLOWING CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE RADIO INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPTANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

FCP-75 Manual — P/N:LS10147-003FK-E:A 3/17/2021 13

Underwriters Laboratories (UL) Agency Listings, Approvals, and Requirements

2.2 Underwriters Laboratories (UL)

2.2.1 Requirements for All Installations

General requirements are described in this section. When installing an individual device, refer to the specific section of the manual for addi-

tional requirements. The following subsections list specific requirements for each type of installation (for example, Central Station Fire

Alarm systems, Local Protected Fire Alarm systems, and so on). See Section 10.7 for information on releasing operation.

1. All field wiring must be installed in accordance with NFPA 70 National Electric Code.

2. Use the addressable smoke detectors specified in Section 7 of this manual.

3. Use UL listed notification appliances compatible with the FCP-75 from those specified in the Appendix at the back of this manual.

4. A full system checkout must be performed any time the panel is programmed.

Restricted Options:

• The loss of AC signal is defaulted to 3 hours however the system allows settings from 0 - 30 hours. For UL certified installations this

number must be set from 1 to 3 hours.

• The system allows the use of non-latching spot type smoke detectors.This feature may not be used in commercial applications whereby

a general alarm is sounded. It is intended for elevator recall, door holding applications, and hotel/motel room applications.

• The system allows the Alarm Verification time to be set from 60 to 250 seconds. For UL certified installations the setting must be a

maximum of 60 seconds.

• The systems allows the Auto-resound time to be set to 4 or 24 hours. For ULcertified installations that are utilizing SWIFT devices, the

value must be set to 4 hours.

• Call forwarding shall not be used.

• When two count is used detector spacing shall be cut in half, you shall not use the alarm verification feature, and no delay shall be used.

• P.A.S (positive alarm sequence) feature shall be used only with automatic detectors.

2.2.2 Requirements for Central Station Fire Alarm Systems

1. Use both phone lines. Enable phone line monitors for both lines.

2. You must program a phone number and a test time so that the FCP-75 shall automatically initiate and complete a test signal

transmission sequence to its associated receiver at least once every 6 hrs. The AC Loss Hours option must be set from 1-3 hours.

3. If using wired Ethernet, you must program the corresponding account/subscriber ID and a test time so that the FACP shall automatically

initiate a test signal transmission sequence to its associated receiver at least once every 6 hrs.

2.2.3 Requirements for Local Protected Fire Alarm Systems

At least one UL listed supervised notification appliance must be used.

2.2.4 Requirements for Remote Station Protected Fire Alarm Systems

1. Do not exceed the current load restrictions shown in Section 3.7.

2. The AC Loss Hours option must be set from 1-3 hours.

2.2.5 Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning

Equipment, NFPA 720

When using carbon monoxide detection the system must be monitored by a Supervising Station.

CAUTION: INSTALLATION AND TEST

TO ENSURE PROPER OPERATION, THIS EQUIPMENT MUST BE INSTALLED ACCORDING TO THE ENCLOSED

INSTALLATION INSTRUCTIONS. TO VERIFY THAT THE EQUIPMENT IS OPERATING PROPERLYAND CAN

SUCCESSFULLY REPORTAN ALARM, THIS EQUIPMENT MUST BE TESTED IMMEDIATELY AFTER INSTALLATION,

AND PERIODICALLY THEREAFTER, ACCORDING TO THE ENCLOSED TEST INSTRUCTIONS.

CAUTION: LINE IN USE

IN ORDER FOR “ALARM DIALING EQUIPMENT” TO BE ABLE TO SEIZE THE PHONE LINE TO REPORTAN ALARM OR

OTHER EVENT WHEN OTHER CUSTOMER EQUIPMENT (TELEPHONE,ANSWERING SYSTEM, COMPUTER MODEM,

ETC.) CONNECTED TO THE SAME LINE IS IN USE, “ALARM DIALING EQUIPMENT” MUST BE CONNECTED TO A

PROPERLY INSTALLED RJ31X JACK. THE RJ31X JACK MUST BE CONNECTED IN SERIES WITH, AND AHEAD OF, ALL

OTHER EQUIPMENTATTACHED TO THE SAME PHONE LINE. SERIES INSTALLATION OF AN RJ31X JACK IS DEPICTED

IN THE FIGURE BELOW. IF YOU HAVE ANY QUESTIONS CONCERNING THESE INSTRUCTIONS, CONSULT YOUR

TELEPHONE COMPANY OR A QUALIFIED INSTALLER ABOUT INSTALLING THE NECESSARY JACKAND ALARM

DIALING EQUIPMENT.

14 FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Agency Listings, Approvals, and Requirements Underwriters Laboratories (UL)

2.2.6 NFPA Requirements

The following is the minimum configuration to meet the NFPA requirements.

Model/Module Description Local Releasing Remote

Station Auxiliary Central

Station Emergency

Signaling

0067000 Main board YYYYYY

FIK-5496 NAC expander O Y O O O O

5220 Direct connect module NNNYNO

FIK-NIC NetworkcardOOOOOO

FIK-FML/ -FSL Fiber module OOOOOO

Y = YES, N = NO, O = OPTIONAL

Table 2.1 NFPA Requirements for FCP-75

FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021 15

Section 3: Before You Begin Installing

This section of the manual is intended to help you plan your tasks to facilitate a smooth installation. Please read this section thoroughly, espe-

cially if you are installing an FCP-75 panel for the first time.

3.1 Inventory

When the FCP-75 shipment is received, check that all the parts have been included in the shipment. The shipment consists of one of each of

the following:

• main circuit board with display

• backbox with door

• plastic bag containing two keys, screws, cables, and ten 4.7K ohm end-of-line resistors

• manual

3.2 Environmental Specifications

It is important to protect the FCP-75 control panel from water. To prevent water damage, the following precautions should be FOLLOWED

when installing the units:

• Intended for indoor use in dry locations only.

• Do not mount directly on exterior walls, especially masonry walls (condensation).

• Do not mount directly on exterior walls below grade (condensation).

• Protect from plumbing leaks.

• Protect from splash caused by sprinkler system inspection ports.

• Do not mount in areas with humidity-generating equipment (such as dryers, production machinery).

When selecting a location to mount the FCP-75 control panel, the unit should be mounted where it will NOT be exposed to temperatures out-

side the range of 0°C-49°C (32°F-120°F) or humidity outside the range of 10%-93% at 30°C (86°F) noncondensing.

3.3 Software Downloads

In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades

to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that

you download the most current version of software for each product prior to commissioning any system. Contact Technical Support with any

questions about software and the appropriate version for a specific application. The HFSS Programming Tool is available at wwwfike.com.

3.4 Electrical Specifications

Table 3.1 list the terminal block on the FCP-75 as well as a description of the each individual terminal and their respective electrical rating.

For location of the terminals refer to Figure 3.2. See also Section 4 for installation.

Terminal No. Label Description Rating

Group Individual Voltage Current

Terminal Block 3 TELCO 1 RING Phone Line 1 Telco Ring

TIP Phone Line 1 Telco Tip

PHONE 1 RING Phone Line 1 Phone Ring

TIP Phone Line 1 Phone Tip

TELCO 2 RING Phone Line 2 Telco Ring

TIP Phone Line 2 Telco Tip

PHONE 2 RING Phone Line 2 Phone Ring

TIP Phone Line 2 Phone Tip

Terminal Block 2 RELAY 1 NO Normally open relay contact 27.4 VDC 2.5 A, resistive

COM Common terminal

NC Normally closed relay contact

RELAY 2 NO Normally open relay contact 27.4 VDC 2.5 A, resistive

COM Common terminal

NC Normally closed relay contact

TROUBLE NO Normally open relay contact 27.4 VDC 2.5 A, resistive

COM Common terminal

NC Normally closed relay contact

SLC IN – Used for Class A installations 32 VDC 100 mA

Table 3.1 Terminal Descriptions and Electrical Specifications

16 FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Before You Begin Installing Wiring Specifications

3.5 Wiring Specifications

Induced noise (transfer of electrical energy from one wire to another) can interfere with telephone communication or cause false alarms. To

avoid induced noise, follow these guidelines:

• Isolate input wiring from high current output and power wiring. Do not pull one multi-conductor cable for the entire panel. Instead,

separate the wiring as follows:

• Do not pull wires from different groups through the same conduit. If you must run them together, do so for as short a distance as

possible or use shielded cable. Connect the shield to earth ground at the panel. You must route high and low voltages separately.

• Route the wiring around the inside perimeter of the cabinet. It should not cross the circuit board where it could induce noise into the

sensitive microelectronics or pick up unwanted RF noise from the high speed circuits. See Figure 3.1 for an example.

• High frequency noise, such as that produced by the inductive reactance of a speaker or bell, can also be reduced by running the wire

through ferrite shield beads or by wrapping it around a ferrite toroid.

Figure 3.1 Wire Routing Example

Terminal Block 2 SLC OUT – SLC terminals 32 VDC 100 mA

SLC PROG – Used for programming SLC Detectors 32 VDC 100 mA

SBUS – SBUS Power 27.4 VDC 0.5 A

A SBUS Communication 5 VDC 100 mA

NAC1* – Notification Appliance Circuit/Auxiliary

power 27.4 VDC 1 Amp NAC or Aux power

NAC2* – Notification Appliance Circuit/Auxiliary

power 27.4 VDC 1 Amp NAC or Aux power

P7 Data Network Used for FIK-NIC 24 VDC 21 mA

Note: Regulated NAC application. When programmed for releasing, NAC are Special Application.

Terminal No. Label Description Rating

Group Individual Voltage Current

Table 3.1 Terminal Descriptions and Electrical Specifications (Continued)

High voltage AC power Terminals

SLC loops

Audio input/output Phone line circuits

Notification circuits NAC1 through NAC2

SBUS

Relay circuits Table 3.2 Wiring Specifications

Relay

NAC / Aux Power

Outputs

SBUS

Phone

SLC IN/OUT

AC Power

Input

Devices

Lines

Outputs

Battery Battery

1/4” spacing must

be maintained

between each of

these circuit types;

as well as between

power-limited and

non-power-limited

circuits.

Board Assembly Diagram Before You Begin Installing

FCP-75 Manual — P/N:LS10147-003FK-E:A 3/17/2021 17

3.6 Board Assembly Diagram

Figure 3.2 Model FCP-75 Assembly

Figure 3.2 shows the circuit boards, and annunciator. If you should need to remove the control board for repair, remove the three mounting

screws which hold the control board in the cabinet. Then lift the control board out of the cabinet.

3.7 Calculating Current Draw and Standby Battery

This section is for helping you determine the current draw and standby battery needs if you are using IDP addressable devices (Table 3.3).

3.7.1 Current Draw Worksheet Requirements

The following steps must be taken when determining FCP-75 current draw and standby battery requirements.

1. For the FCP-75, the worst case current draw is listed for the panel, addressable devices, and all SBUS expanders. Fill in the number of

addressable devices that will be used in the system and compute the current draw requirements for alarm and standby. Record this

information in the Current Calculation Worksheet at Line A.

2. Add up the current draw for all auxiliary devices and record in the table at Line B.

3. Add up all notification appliance loads and record in the table at Line C.

4. For notification appliance circuits and auxiliary devices not mentioned in the manual, refer to the device manual for the current ratings.

5. Make sure that the total alarm current you calculated, including current for the panel itself, does not exceed 2.5A. This is the maximum

alarm current for the FCP-75 control panel.

If the current is above 2.5Ayou will need to use a notification power expander(s) such as the FIK-5496 NAC Expander, to distribute the

power loads so that the FCP-75 or the power expanders do not exceed their power rating. Refer to the current draw worksheets provided

with the FIK-5496 manual so you do not exceed their power requirements.

6. Complete the remaining instructions in the Current Calculation Worksheet for determining battery size requirements.

On-board

Annunciator

NAC/Aux

Power Circuits

Phone Lines SLC In/Out,

SLC Programming

AC Power

Input

SBUS

Connections

Battery

Connector

Program

Port

Form C

Trouble Relay

120 VAC,

60 Hz, 1.5A

18 FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Before You Begin Installing Calculating Current Draw and Standby Battery

3.7.2 Current Draw Worksheet for Fike IDP SLC Devices

Use Table 3.3 to determine current requirements during alarm/battery standby operation when SLC devices are installed. You can install up

to 75 IDP detectors and 75 IDP modules1.

Device # of Devices Current per Device Standby

Current Alarm Current

For each device use this formula: This column X This column = Current per number of devices.

Fire Panel (Current draw from battery) 1 Standby: 165 mA 165 mA

Alarm: 310 mA 310 mA

Addressable SLC Detectors

FIK-2351 SLC Standby: 200µA mA

Alarm: 4.5mA mA

FIK-2351R SLC Standby: 200µA mA

Alarm: 4.5mA mA

FIK-2351T SLC Standby: 200µA mA

Alarm: 4.5mA mA

FIK-5351 SLC Standby: 200µA mA

Alarm: 4.5mA mA

FIK-5351R SLC Standby: 200µA mA

Alarm: 4.5mA mA

FIK-5351H SLC Standby: 200µA mA

Alarm: 4.5mA mA

DNR5(non-Relay) None, included with FIK-2351R 6

DNR6(with Relay) None, included with FIK-2351R & FIK-M500R7

Addressable SLC Modules

FIK-M500M Standby/Alarm 0.375 mA mA mA

FIK-M501M mA mA

FIK-PULL-SA/FIK-PULL-DA

FIK-M500DM Standby/Alarm: 0.75mA mA mA

FIK-IM-10 Standby/Alarm: 3.5mA mA mA

FIK-M500S SLC Standby: 0.375mA

Alarm: 0.375mA mA mA

Aux Pwr Standby: 1.7mA mA

Alarm: 7mA mA

FIK-SC-6 SLC Standby: 2.25mA

Alarm: 2.25mA mA mA

Aux Pwr Standby: 8mA mA

Alarm: 20mA mA

FIK-M500R Standby/Alarm: .255mA mA mA

FIK-CR-6 Standby/Alarm: 1.45mA mA mA

FIK-M500MR-2 Standby: 1.3mA mA

Alarm: 24mA mA

FIK-M502M Aux Pwr Standby: 12mA mA mA

Alarm: 90mA mA mA

SLC Standby/Alarm: .27mA mA mA

FIK-CZ-6 Aux Pwr Standby: 50mA mA mA

Alarm: 270mA mA mA

SLC Standby/Alarm: 2mA mA mA

SLC Accessories

B200S-WH / -IV Intelligent sounder base Aux Pwr Standby: .5mA mA

Alarm: (high vol) 35mA mA

SLC Standby .3mA mA

B200S-LF-WH / -IV Low Frequency sounder base Aux Pwr Standby .55mA mA

Alarm (high vol) 140mA mA

SLC Standby .30mA mA

B224RB-WH / -IV Relay Base Standby/Alarm: .5mA mA mA

SLC Isolator Devices

FIK-M500X (100 max.) Standby/Alarm: .45mA mA mA

Color Guide: -IV = Ivory color, -BL = Black, -WH = White, -WHITE-White

Table 3.3 Current Calculation Worksheet for Fike IDP Devices

Calculating Current Draw and Standby Battery Before You Begin Installing

FCP-75 Manual — P/N:LS10147-003FK-E:A 3/17/2021 19

1. Total does not include isolator devices or accessory bases.

2. If using door holders, you do not need to consider door holder current for alarm/battery standby, because power is removed during

that time. However, during normal operation, door holders draw current and must be included in the 2.5Atotal alarm current (1.0A

for all other conditions) that can be drawn from the panel.

3. Use next size battery with capacity greater than required.

4. The FIK-2351R is sold separately from the DNR. Current draw for the DNR + FIK-2351R is calculated by increasing the “Number

of Devices” column for each FIK-2351R used with a DNR.

5. The DNR housing does not include a Relay circuit board. If a relay is needed, be sure to add one to the FIK-M500R & FIK-2351R

“Number of Devices” column for each DNR used for correct current calculations.

6. The FACP can only support 5 devices w/LED’s on. This current draw has been added to the panels alarm current.

Accessories Modules

FIK-RA2000 Remote LCD Annunciator (8 max.) Standby: 25 mA mA

Alarm: 50 mA mA

FIK-RA100 Remote LCD Annunciator Standby: 20 mA mA

Alarm: 25 mA mA

FIK-RA1000R Remote LCD Annunciator Standby: 20 mA mA

Alarm: 25 mA mA

FIK-5824 Serial / Parallel Module (4 max.) Standby/Alarm: 45mA mA mA

FIK-5496 NAC Expander (8 max.) Standby/Alarm: 10 mA mA mA

FIK-RPS1000 Power Supply Standby/Alarm: 10 mA mA mA

FIK-5865-4 LED Annunciator

(with reset and silence switches) (8 max.) Standby: 35 mA mA

Alarm: 145 mA mA

FIK-5865-3 LED Annunciator Standby: 35 mA mA

Alarm: 145 mA mA

FIK-5880 LED I/O Module Standby: 35 mA mA

Alarm: 200 mA mA

FIK-5883 Relay Interface (32 max.) Standby: 0 mA mA

Alarm: 220 mA

(22 mA per relay) mA

FIK-NIC Network Interface Card (1 Max.) Standby/Alarm: 21 mA mA mA

FIK-FML Fiber Optic Multi Mode (1 Max.) Standby/Alarm: 53 mA mA mA

FIK-FSL Fiber Optic Single Mode (1 Max.) Standby/Alarm: 79 mA mA mA

Wireless Modules

FIK-W-WGI Wireless Gateway Max current using external supply 40 mA mA mA

Max current SLC Power 24 mA mA mA

Total System Current

Auxiliary Devices2Refer to devices manual for current rating.

Alarm/Standby: mA mA mA

Auxiliary Devices Current

Notification Appliance Circuits Refer to device manual for current rating.

Alarm: mA mA

Notification Appliances Current mA

Total current ratings of all devices in system (line A + line B + C) mA mA

Total current ratings converted to amperes (line D x.001): A A

Number of standby hours (24 or 60 for NFPA 72, chapter 1, 1-5.2.5): H

Multiply lines E and F. Total standby AH AH

Alarm sounding period in hours. (For example, 5 minutes =.0833 hours) H

Multiply lines E and H. Total alarm AH AH

Add lines G and I. 3AH

Multiply by the Derating Factor x 1.25

Total ampere hours required AH

Device # of Devices Current per Device Standby

Current Alarm Current

Table 3.3 Current Calculation Worksheet for Fike IDP Devices (Continued)

20 FCP-75 Manual — P/N LS10147-003FK-E:A 3/17/2021

Before You Begin Installing Calculating Current Draw and Standby Battery

Maximum Battery Standby Load

The table below shows the maximum battery standby load for the FCP-75 based on 24 and 60 hours of standby. The standby load calcula-

tions of line D in the Current Draw Calculation Worksheet (Table 3.4) must be less than the number shown in the table below for the battery

size used and standby hours required.

Rechargeable Battery Size Max. Load 24hrs Standby,

5 minutes Alarm *Max. Load for 60hrs Standby,

5 minutes Alarm

7AH 221mA 85mA

18AH 675mA 250mA

33AH 1.1A 450mA

Table 3.4 Maximum Battery Standby Load

NOTE: *Required for NFPA 72 Auxiliary Protected FireAlarm systems for Fire Alarm Service (City Box) and Remote Station Protected Fire

Alarm systems (Polarity Reversal) and Digital Alarm Communicator/Transmitter (DACT).

WARNING: BATTERIES

FIKE DOES NOT SUPPORT THE USE OF BATTERIES SMALLER THAN THOSE LISTED IN TABLE ABOVE. USING A

BATTERY TOO SMALL FOR THE CONFIGURATION COULD OVERLOAD THE BATTERY, RESULTING IN THE BATTERY

HAVING LESS THAN THE REQUIRED 24 HOURS STANDBY POWER. USE THE CURRENT CALCULATION WORKSHEET

TO CALCULATE THE CORRECT BATTERYAMPERES/HOUR RATING NEEDED FOR THE SYSTEM CONFIGURATION.

Other manuals for FCP-75

Table of contents

Other Fike Control Panel manuals

Fike

Fike FCP-75 User manual

Fike

Fike FIK-RA100BD Technical manual

Fike

Fike TWINFLEXpro User manual

Fike

Fike TWINFLEXpro User manual

Fike

Fike SITA200plus User manual

Fike

Fike FCP-2100 User manual

Fike

Fike FIK-RA2000 Technical manual

Fike

Fike CIE-A-200 User manual

Fike

Fike FIK-5496 User manual

Fike

Fike FCP-300 User manual

Fike

Fike Twinflex pro2 User manual

Fike

Fike FCP-2100ECS User manual

Fike

Fike TWINFLEX SRP 100-0001 User manual

Fike

Fike Quadnet User manual

Fike

Fike GB2426367 User manual

Popular Control Panel manuals by other brands

Allen-Bradley

Allen-Bradley 9 Series install guide

Global

Global JUNIOR V4 Installation & commissioning manual

Panasonic

Panasonic AV-SF500 operating instructions

Bartlett

Bartlett V6-CF Operation manual

CBE

CBE PC-540HY instruction manual

DALGAKIRAN

DALGAKIRAN L-8 user manual

IDS

IDS X Series Installer manual

Ampac

Ampac LoopSense MAN 1572-4 user manual

VDH

VDH MC 795D operating manual

Salda

Salda FLEX Technical manual

DITEC

DITEC 99 installation manual

AMX

AMX AutoPatch CP-15 instruction manual

GE NetworX NX-8E user manual

Texecom

Texecom Premier 412 Premier 816 Premier 832 installation manual

tau

tau K550M installation guide

GARDINER TECHNOLOGY

GARDINER TECHNOLOGY Gardtec 800 installation instructions

DITEC

DITEC LCU43A installation manual

Extron electronics

Extron electronics NBP 100 user guide