FireplaceXtrordinair ProBuilder 36 CleanFace User manual

ProBuilder 36/42 CleanFace Fireback Installation
PB 36 CF Glass sku# 96100851 PB 42 CF Glass sku# 96100861
PB 36 CF Brick sku# 96100850 PB 42 CF Brick sku# 96100860
Page 1 of 3 17602039 - 5/1/19 © Travis Industries, Inc.
Compatibility
ProBuilder 36 Clean Face Fireplace
ProBuilder 42 Clean Face Fireplace
Packing List
(1) Rear Fireback
(2) Side Firebacks
CERAMIC FIREBACKS ARE FRAGILE
HANDLING THE FIREBACKS: The firebacks are fragile – especially after being burned. Take care to prevent
contacting/scraping the fireback against metal or rough surfaces. You may wish to lay out a blanket during
installation in case you need to set the firebacks down.
GLASS FIREBACK WARNINGS
HANDLING THE FIREBACKS: The glass firebacks are fragile – especially the edges. Take care to prevent
contacting/scraping the glass against metal or rough surfaces. You may wish to lay out a blanket during
installation in case you need to set the firebacks down.
We recommend the use of gloves and safety glasses during the installation of the glass firebacks.
GLASS FIREBACK CLEANING
These firebacks require periodic cleaning. Do not use ammonia-based cleaners (this may cloud the glass).
We recommend ammonia-free glass cleaner (i.e. vinegar and water) to clean the fireback.
Install the firebacks after the fireplace is in position.
Install the firebacks after the optional Ember-Glo lights.
Install the firebacks before installing the log set.
ProBuilder 42 CF Only – Remove Rivet Cover
Remove and discard the the rivet cover (see illustration below). After installing the rear
fireback, replace the fireback clips to secure the rear fireback (see instructions on following
pages).
Remove the clips on both sides (these clips have
key-holes, allowing removal without removing the
screw). Keep the screws and clips.
1/4" Nutdriver





a
Remove and discard the rivet cover.

ProBuilder 36/42 CleanFace Fireback Installation
PB 36 CF Glass sku# 96100851 PB 42 CF Glass sku# 96100861
PB 36 CF Brick sku# 96100850 PB 42 CF Brick sku# 96100860
Page 2 of 3 17602039 - 5/1/19 © Travis Industries, Inc.
Installation
WARNING Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.
1. Remove the glass frame and logs (see the installation manual for details).
2. Remove the firebox baffle from the firebox ceiling (see illustration below).
NOTE: The baffle is replaced once the firebacks are in place.
3. Remove the two front fireback clips from the ceiling of the fireplace (see illustration below).



Firebox Ceiling
The baffle has keyholes, allowing removal by loosening the
screws and sliding the baffle forward.
Firebox Baffle
Remove the clips on
both sides (these
clips have key-
holes, allowing
removal without
removing the screw)
1/4" Nutdriver






ProBuilder 36/42 CleanFace Fireback Installation
PB 36 CF Glass sku# 96100851 PB 42 CF Glass sku# 96100861
PB 36 CF Brick sku# 96100850 PB 42 CF Brick sku# 96100860
Page 3 of 3 17602039 - 5/1/19 © Travis Industries, Inc.
4. Install the rear fireback (see “a” below). On PB 42 CF fireplaces, replace the rear fireback clips to secure
the rear fireback in place. Place one side fireback in place (see “b” below) and secure with the front
fireback clip (see “c” below). Repeat this process for the opposite side fireback.
5. Restore the fireplace to the correct configuration.
1/4" Nutdriver
Rear Fireback Clips (PB 42 CF Only)






a
b
1/4" Nutdriver
c
CERMAMIC FIREBACKS
Make sure the rear fireback is
positioned with the full bricks at
the top.