FireplaceXtrordinair 864 User manual

864 Double-Door Onlay
Arch Bronze 96300790 Arch Nickel 96300791 Arch Copper 96300792
Rect. Bronze 96300800 Rect. Nickel 96300801 Rect. Copper 96300802
Page 1 of 4 12/20/07 © Travis Industries, Inc.
Compatibility:
• 864 TRV Fireplace with FPX Double-Doors
• 864 HH Fireplace with FPX Double-Doors
• 864 ST Fireplace with FPX Double-Doors
Packing List:
• (2) Door Onlays (Left and Right Side)
• (6) 8-32 Acorn Nuts
• 13/64” Drill Bit
Installation
1 Remove the center screen and handle from the door (both sides).

864 Double-Door Onlay
Arch Bronze 96300790 Arch Nickel 96300791 Arch Copper 96300792
Rect. Bronze 96300800 Rect. Nickel 96300801 Rect. Copper 96300802
Page 2 of 4 12/20/07 © Travis Industries, Inc.
2 With the doors removed, locate the three holes used to secure the center screen to the door (see the
illustration below). Use the included 13/64” drill bit to drill through the doors in these locations (both doors).
Remove any burrs from the holes.

864 Double-Door Onlay
Arch Bronze 96300790 Arch Nickel 96300791 Arch Copper 96300792
Rect. Bronze 96300800 Rect. Nickel 96300801 Rect. Copper 96300802
Page 3 of 4 12/20/07 © Travis Industries, Inc.
864 TRV and 864 ST Screen Warning
Remove the screen from either the glass frame (on the fireplace – see operation manual) or doors
(center screen only). Operating the appliance with both screens in place will lead to a safety hazard and
void the warranty. See the instructions included with the double-doors for removing the screen from the
glass frame on the fireplace.
864 HH Screen Application
You have the option of either leaving the door screen in place or removing it on the 864 HH. There is no
screen in the 864 HH glass frame assembly.
3 Follow the directions below to install.
Handling the Plated Onlays
Use non-scratching gloves to handle the onlays. Because of the intricate pattern cut into this accessory,
fingerprints (or other marks) left on the onlays become difficult to clean off once in place. Before
installing, remove the protective wrap.
Installation With No Door Screen
Install the onlays and handles as shown below. Use the washers removed in step 1 when attaching (as well
as the acorn nuts included with this kit).
Helpful Hint
During shipment the onlays may develop a slight bow. If the onlays don’t seat flat against the
doors, simply remove the onlay and gently straighten by hand. Be careful to not over-adjust.

864 Double-Door Onlay
Arch Bronze 96300790 Arch Nickel 96300791 Arch Copper 96300792
Rect. Bronze 96300800 Rect. Nickel 96300801 Rect. Copper 96300802
Page 4 of 4 12/20/07 © Travis Industries, Inc.
InstallationWith Door Screen in Place (Screen from fireplace MUST be removed)
Install the onlays and handles as shown below. Use the included acorn nuts to attach - do not use the
washers removed in step 1.
Helpful Hint
During shipment the onlays may develop a slight bow. If the onlays don’t seat flat against the
doors, simply remove the onlay and gently straighten by hand. Be careful to not over-adjust.
Plated Surfaces (Bronze & Nickel)
Use denatured alcohol and a soft cloth to clean plated surfaces. Marks
left on the surface may damage the face.
Copper-Plated Surfaces
See the instructions included with these onlays for cleaning with citric
acid.
Denatured
Alcohol
Soft Cloth