FireplaceXtrordinair 99300497 User manual

864TRV Arched Face
Classic Black 99300497 Artisan 99300498 French Country 99300499
Page 1 of 6 6/8/05 © Travis Industries, Inc.
Compatibility:
• 864TRV Fireplace
Installation Details
Packing List:
• Face
• Face Brackets
• Arched Tiling Guide
• Glass Frame Cover
41-1/2”
36"
5"
Radius = 45-3/4”
NOTE FOR THICK FACING (BRICK, ROCK, ETC.):
This face requires a 1/4”gap above and to the sides of the face for face installation. We
strongly recommend using the 864 Arched Face Template (SKU xxxxxxxx) when installing
thick facing. The template acts as a support for the facing and allows the mason to construct
facing directly up to the template.
SIDE OF FIREPLACE
1”
9/16”TO 1”
NOTE:
This face has an adjustable bracket that allows for
different facing depths to be tucked under the face.
NOTE FOR THIN FACING (TILE, GRANITE, OR OTHER NON-
COMBUSTIBLE UNDER 1”)
An arched tiling guide is provided to aid in face installation. It attaches to the
fireplace and is used as a guide for tucking tile (or other non-combustible) under
the face. It also prevents the facing from being installed in a location where it
would be viewed through the face.

864TRV Arched Face
Classic Black 99300497 Artisan 99300498 French Country 99300499
Page 2 of 6 6/8/05 © Travis Industries, Inc.
Installation
1 Install the face mounting brackets onto the fireplace following the directions below.
Remove the nuts and bushings above and
below the firebox.
Place the upper and lower brackets in place
and secure using the nuts removed earlier.
Repeat these steps for the opposite side.
Discard the
bushings.
Upper
Bracket
Lower
Bracket
Discard the
bushings.

864TRV Arched Face
Classic Black 99300497 Artisan 99300498 French Country 99300499
Page 3 of 6 6/8/05 © Travis Industries, Inc.
2 Install the arched tiling guide following the directions below.
Loosen the nuts on the upper
brackets three turns (both sides).
Slide the tiling guide into place.
NOTE: the tiling guide has slots that
slide between the brackets and the
fireplace.
Re-tighten the nuts on the brackets
(typically you only need to tighten the
lower nuts).
Use the four included screws to secure
the tiling guide to the fireplace.
a
b
c
d

864TRV Arched Face
Classic Black 99300497 Artisan 99300498 French Country 99300499
Page 4 of 6 6/8/05 © Travis Industries, Inc.
3 At this point the facing (and hearth) should be installed. The facing above the fireplace must be tiled down to
the tiling guide (see the illustration below). The area below the face (1") should be faced over (for raised
fireplaces) or a 1" hearth installed. See the installation manual for further details.
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
Maximum 1`”Hearth
Floor-Level
Fireplaces
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
Raised
Fireplaces
Note how the tile is 1”
(maximum) above the
base of the fireplace.

864TRV Arched Face
Classic Black 99300497 Artisan 99300498 French Country 99300499
Page 5 of 6 6/8/05 © Travis Industries, Inc.
4 Install the glass frame cover following the directions below.
Push these pins inwards
to lock the cover in place.
Place the cover over the top of the door frame.

864TRV Arched Face
Classic Black 99300497 Artisan 99300498 French Country 99300499
Page 6 of 6 6/8/05 © Travis Industries, Inc.
5 Install the face following the directions below.
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAA
AAA
AAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
Position the face so the barbed hooks insert into
the slots on the brackets. The multiple barbs
allow for different facing thicknesses.
Plated Surfaces
Use denatured alcohol and a soft cloth to clean plated surfaces. Marks
left on the surface may damage the face.
Denatured
Alcohol
Soft Cloth