FireplaceXtrordinair 94500971 User manual


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 1 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Compatibility
ProBuilder Linear Fireplaces
42 ProBuilder Linear 54 ProBuilder Linear 72 ProBuilder Linear MV
MV SN# 3220-000805 or later SN# 3221-000311 or later SN# 3222-000251 or later
GSB2/GSR2 SN# 3217-002083 or later SN# 3218-001010 or later SN# 3219-001043 or later
NOTE: If using this log set kit with a ProBuilder fireplace prior to the above SN#’s, you will need to purchase a
replacement media tray (see part numbers below).
 42 ProBuilder Linear Media Tray – sku# 250-05352
 54 ProBuilder Linear Media Tray – sku# 250-05353
 72 ProBuilder Linear Media Tray – sku# 250-05354
HO Linear Fireplaces
 3615 HO GSR2 - SN# 3213-003633 or later
 4415 HO GSR2 - SN# 3212-012115 or later
 6015 HO GSR2 - SN# 3214-007337 or later
Table of Contents
Compatibility..............................................................................................................................................................1
PackingList.................................................................................................................................................................2
ToolsRequired............................................................................................................................................................3
InstallationNotes........................................................................................................................................................3
ProBuilderUnits..........................................................................................................................................................4
PreparingtheMediaTray–42ProBuilder..........................4
PreparingtheMediaTray–54ProBuilder..........................5
PreparingtheMediaTray–72ProBuilder..........................6
LogInstallation–42ProBuilder...................................................................................................................................7
42ProBuilder‐Overview:...................................................7
42 ProBuilder Log Install ....................................... 7
LogInstallation–54ProBuilder...................................................................................................................................11
54ProBuilder‐Overview:...................................................11
54 ProBuilder Log Install ....................................... 11
LogInstallation–72ProBuilder...................................................................................................................................17
72ProBuilder‐Overview:...................................................17
72 ProBuilder Log Install ....................................... 17
HOLINEARUNITS........................................................................................................................................................22
PreparingtheMediaTray–3615........................................22
PreparingtheMediaTray–4415........................................23
PreparingtheMediaTray–6015........................................24
LogInstallation–3615HO...........................................................................................................................................25
3615HOOverview:.............................................................25
3615 HO Log Install .............................................. 25
LogInstallation–4415HO...........................................................................................................................................28
4415HOOverview:.............................................................28
4415 HO Log Install .............................................. 28
LogInstallation–6015HO...........................................................................................................................................34
6015HOOverview:.............................................................34
6015 HO Log Install .............................................. 34
CrushedGlassInstallation(seemanualforadditionaldetails)......................................................................................40



Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 2 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Packing List
 10 piece log set (see below)



Hardware Pack
(1) #35 Stone Locating Tab (1) #13 Stone Locating Tab
(7) Log Locating Plate (1) #10 Stone Locating Tab
(1) #32 Stone Locating Tab (1) Angled Log Locating Tab
(1) Tall Log Locating Plate (20) Screws - 8x3/8” - Black
(f)
(c)
#35 Stone
#10 Stone
(e)
#32 Stone
(d)
#13 Stone
(a)
(b)


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 3 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Tools Required
 Philips Screwdriver
Installation Notes
WARNINGS:
 Make sure the gas control valve is OFF and the heater is cool prior to conducting service.
 Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved
with this appliance may result in property damage or personal injury.
HINTS:
 The fireplace should be in place, with the gas line and vent attached and the firebacks installed (see owner’s
manual for further details).
 If using propane (LP), convert the appliance before installing the logs (see the owner’s manual for details).
ORDER OF INSTALLATION:
 If converting to LP (propane), convert the appliance prior to installing the log set.
 The fireplace should be in place, with the gas line and vent attached and the firebacks installed (see owner’s
manual for further details).


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 4 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Small holes indicate
location of tabs

ProBuilder Units
Preparing the Media Tray – 42 ProBuilder
1. Remove the glass frame assembly to gain access to the firebox (see manual for details).
2. The map below shows the location of the log and stone locating tabs in relation to the media tray.
Look in the approximate location indicated and you will notice holes that are slightly smaller than the
others. The smaller holes will receive the screws that secure the log locating tabs to the media tray.
HINTS:
 Lay all the locating brackets in their approximate location and orientation. Then go back with
a flashlight and screwdriver (with screws) to locate the attachment holes and secure the
brackets.
 Do not to overtighten the screws when securing the log/stone locating tabs to the media tray.
KEY
 AL = Angled Log Placement plate.
 L = Log Placement plate.
 #xx tabs refer to the number stamped on the stone tab (and corresponding stone).
 The arrow ( ) points to the bent up portion of the stone placement tab (see
illustration to the right).

#35
L
L
L
L
#10
#13 AL
#32


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 5 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Small holes indicate
location of tabs

Preparing the Media Tray – 54 ProBuilder
1. Remove the glass frame assembly to gain access to the firebox (see manual for details).
2. The map below shows the location of the log and stone locating tabs in relation to the media tray.
Look in the approximate location indicated and you will notice holes that are slightly smaller than the
others. The smaller holes will receive the screws that secure the log locating tabs to the media tray.
HINTS:
 Lay all the locating brackets in their approximate location and orientation. Then go back with
a flashlight and screwdriver (with screws) to locate the attachment holes and secure the
brackets.
 Do not to overtighten the screws when securing the log/stone locating tabs to the media tray.
KEY
 L = Log Placement plate.
 #xx tabs refer to the number stamped on the stone tab (and corresponding stone).
 The arrow ( ) points to the bent up portion of the stone placement tab (see
illustration to the right).





L
L L L
L
L
#13 D
#32
#35


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 6 of 41 17602103 — 11/20/19 © Travis Industries, Inc.

Small holes indicate
location of tabs
Preparing the Media Tray – 72 ProBuilder
3. Remove the glass frame assembly to gain access to the firebox (see manual for details).
4. The map below shows the location of the log and stone locating tabs in relation to the media tray.
Look in the approximate location indicated and you will notice holes that are slightly smaller than the
others. The smaller holes will receive the screws that secure the log locating tabs to the media tray.
HINTS:
 Lay all the locating brackets in their approximate location and orientation. Then go back with
a flashlight and screwdriver (with screws) to locate the attachment holes and secure the
brackets.
 Do not to overtighten the screws when securing the log/stone locating tabs to the media tray.
KEY
 TL = Tall Log Placement plate.
 L = Log Placement plate.
 #xx tabs refer to the number stamped on the stone tab (and corresponding stone).
 The arrow ( ) points to the bent up portion of the stone placement tab (see
illustration to the right).


L L
L
L L
L
TL
#32 #35
#10
#13


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 7 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 42 ProBuilder
42 ProBuilder - Overview:
The logs are fragile, especially after being exposed to heat.
42 ProBuilder Log Install
The logs are fragile, especially after being exposed to heat.
 Install log (a) as shown below. The pins on the log locating plates insert into the holes on the log bottom of the
log.
NOTE: There is a pin on the upper right end of the log. This pin is used in another application
but is not required for this installation. Gently use pliers to remove the pin from the log.


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 8 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 42 ProBuilder - continued
 Install log (c) as shown below. The posts on the log supports insert into the holes on the bottom of the log..
 Install stone (#35) as shown below. The slot on the bottom of the stone fits over the bent up portion of the stone
locating tab marked (35). Make sure the printed number on the stone faces the rear of the firebox


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 9 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 42 ProBuilder - continued
 Install stone (#32) as shown below. The slot on the bottom of the stone fits over the bent up portion of the stone
locating tab marked “32”.
 Install log (d) as shown below. There are two holes on the bottom of the log, one round and the other is
elongated. Use the round hole to locate the log the locating plate.


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 10 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 42 ProBuilder - continued
 Install the log (f) as shown below. There are no locating pins for this log. The left end of the log rests on the
(#35) stone and the right side rests on the media tray. Make sure the log does not cause any flame
impingement.
 Install stone (#10) as shown below. The slot on the bottom of the stone fits over the bent up portion of the
stone locating tab marked “10”.
 Install log (e) as shown below. There are no locating pins for this log. The (e) log sits directly in front of the (#35)
rock and the (f) log, on the front portion of the media tray. No part of the log should be placed over the burner.
Make sure the log does not cause any flame impingement.


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 11 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 54 ProBuilder
54 ProBuilder - Overview:
54 ProBuilder Log Install
The logs are fragile, especially after being exposed to heat.
 Install log (a) as shown below. The posts on the log supports insert into the holes on the bottom of the log.



Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 12 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 54 ProBuilder - continued
 Install log (c) as shown below. The right end of the log has a hole on the bottom that fits over the pin on the log
locating plate. The left end of the log has a hole that secures fits over a locating pin on log “a”.
 Install stone (#35) as shown below. The slot on the bottom of the stone fits over the bent up portion of the stone
locating tab marked “35”. Make sure the printed number on the stone faces the rear of the firebox

Theleftendof
thelogrestsona
pinonlog“a”


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 13 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 54 ProBuilder - continued
 Install the (b) as shown below. The posts on the log supports insert into the holes on the bottom of the log.
 Install stone (#10) as shown below. The slot on the bottom of the stone fits over the bent up portion of the stone
locating tab marked “10”. Make sure the printed number on the stone faces the rear of the firebox



Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 14 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 54 ProBuilder - continued
 Install stone (#13) as shown below. The slot on the bottom of the stone insert over the tab on the stone locating
tab that is near the rear of the firebox, behind the right end of log (a). Make sure the printed number on the
stone faces the rear of the firebox
 Install stone (#32) as shown below. The slot on the bottom of the stone insert over the tab on the stone locating
tab marked “32”. Make sure the printed number on the stone faces the rear of the firebox



Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 15 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 54 ProBuilder - continued
 Install log (d) as shown below. There are two holes on the bottom of the log, one round and the other is
elongated. Use the elongated hole to locate the log the locating plate.
 Install log (e) as shown below. There are no locating pins for this log. The left side of the log sits directly on the
(#35) stone. The right end of the log rests on the rear media tray, just to the left of the (#13) stone. No part of the
log should be placed over the burner. Make sure the log does not cause any flame impingement.



Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 16 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 54 ProBuilder - continued
 Install log (f) as shown below. There are no locating pins for this log. The log rests just to the right of the (b) log
and the right side rests on the media tray skirt (see below).



Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 17 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 72 ProBuilder
72 ProBuilder - Overview:
72 ProBuilder Log Install
The logs are fragile, especially after being exposed to heat.
 Install log (b) as shown below. The posts on the log supports insert into the holes on the bottom of the log.
 Install log (a) as shown below. The posts on the log supports insert into the holes on the bottom of the log.


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 18 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 72 ProBuilder - continued
NOTE: There is a pin on the upper right end of
the log. This pin is used in another
application but is not required for this
installation. Gently use pliers to remove
the pin from the log.
 Place the (#13) stone over the “13” stone locating tab as shown below. Make sure the printed number on the
stone faces the rear of the firebox.



Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 19 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 72 ProBuilder - continued
 Rest the (e) log on the stone as shown below. This log should rest against the tall log locating plate and not block
any burner ports.
 Install the (c) log on the stone as shown below. The pins on the log locating plates insert into the holes on the log
bottom of the log. The log may rest against the back wall of the firebox (or fireback). You may wish to adjust the
(e) log to conceal the bracket and support the (c) log.

#13 Stone
Adjust this log to
conceal the bracket
Log may rest against
the back wall
(e) log


Linear Fireplace Driftwood Log Set – PB / HO
Installation Instructions (SKU94500971)

Page 20 of 41 17602103 — 11/20/19 © Travis Industries, Inc.
Log Installation – 72 ProBuilder - continued
 Install the (d) log as shown below. Position the log so the pin on the plate inserts into the hole on the bottom of
the log (the slot is not used). This log points forward and does not cover any burner ports.
 Place the (#35) stone over the “35” stone locating tab as shown below. Make sure the printed number on the
stone faces the rear of the firebox.