FireplaceXtrordinair ProBuilder 42 CF User manual

PB42 CF BonFyre
(sku# 94500772)
Page 1 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Compatibility
 ProBuilder 42 CF (MV, GSB2, GSR2) Fireplace.
Installation Warnings
NOTE: Consult the installation manual for the order of installation. If using propane (LP), convert the
appliance before installing the log set. If using firebacks, install them prior to installing the log set.
 The logs are fragile, especially after being exposed to heat.
 Make sure the gas control valve is OFF and the heater is cool prior to conducting service.
 Failure to position the parts in accordance with these diagrams or failure to use only parts specifically
approved with this appliance may result in property damage or personal injury.
 The burner must be correctly positioned before installing the log set. Make sure the burner is fully seated
and the pilot is properly aligned. See owner’s manual for details on burner removal.
Log Set Overview
When installed, the (10) logs should appear as shown below.
Installation
The installation of this log set should only be done AFTER the unit has been converted to LP Gas (if applicable)
and after the installation of the embers, and Rockwool (MV, GSB2, and GSR2) and the Ember-Glo™ glass
(GSR2 ONLY). See the information on the following (2) pages for details on preparing the burner.
Log #1
Log #4
Log #8 Log #10
Log #9
Log #6
Log #7
Log #2
Log #3
Log #5

PB42 CF BonFyre
(sku# 94500772)
Page 2 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Ember-Glo™ Glass and Ember Material Installation (GSR2 ONLY)
Ember bed Glass Installation
The Ember-Glo™ lights come standard on the GSR2 units. There is an optional accessory for GSB2 or MV units. If the
upgrade kit is not used for the GSB2 or MV units, you may skip this section and proceed to Ember Installation.
 Make sure the ember skirt is in place. The skirt hooks over the front of the ember platform and slopes outward
toward the glass. The skirt helps keep the glass and ember material from falling off the platform when the glass
is removed.
 Locate the perforations in front of the log grate.
 Place a thick layer of the ember glass over the perforations making sure to cover all of the holes completely.
 Lightly dress the ember glass with the black touch-up paint provided. Check the appearance with the lights on
and add additional paint, as needed, for a realistic glowing ember appearance.
NOTE: If power is supplied
to the fireplace it can help
to turn the lights on while
painting so you can
determine an appropriate
amount of paint for a
realistic ember appearance.
NOTE: We recommend
that you use a piece of
paper, cardboard as a
shield to mask the log grate
and burner from overspray
(see below).
Ember Material Installation (GSR2 ONLY)
 Once the ember glass installation is complete, place
a generous amount of ember material on the firebox
floor on either side of the firebox. Completely cover
any visible metal on the firebox floor.
NOTE: Make sure no ember material is placed directly on
the burner.
HINT: Add a few randomly placed ember chunks over the
ember bed glass to produce a more realistic appearance.

PB42 CF BonFyre
(sku# 94500772)
Page 3 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Ember Installation (GSB2 or MV)
A bag of embers is provided to further enhance the firebox.
Place the embers on the firebox floor and the burner. Do
not place embers over any of the burner holes or air
channels.
Rock Wool Placement (All Models)
The included rock wool is placed on top of the burner to enhance the glow from the burner. The rock wool works
best when it is applied in a very thin layer. The best method for applying the rock wool is to brush it onto the
burner. Compress a clump of Rockwool between your thumb and forefinger. Use a stiff brush to apply a thin layer
of Rockwool fibers onto the burner. Do not use the entire bag of Rockwool. Use only a small amount and save the
remainder. Over-use of Rockwool will diminish the glow and may cause sooting or other adverse conditions.
NOTE: Photos are shown without Rockwool for clarity

PB42 CF BonFyre
(sku# 94500772)
Page 4 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Log #1
Log #1 has two holes that fit over two pins on the back burner (see photos below). Put the log in place and push
it back until it is in contact with the back of the firebox or fireback if one is installed.
Push log all the way backward
With log pushed all the way back, line up the notch in
the log with the furthest right burner port on rear burner

PB42 CF BonFyre
(sku# 94500772)
Page 5 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Log #2
Log #1 has three sockets on the top. Log #2 is made up of (3) individual logs connected at the top. The bottom
of each log fits into a socket on the top of log #1. Lean the top portion of log #2 against the back of the firebox.
Log #3
Log #3 has a notch on the right side. The notch fits over the second log grate finger from the left. The upper
portion of the log rests on the sloped portion on the lower portion of log #1, as shown below.
NOTE: Make sure that the log placement does not obstruct any of the burner holes.
Log #1
Log #2

PB42 CF BonFyre
(sku# 94500772)
Page 6 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Log #4
There is a small ridge on the right side of the front burner. Log #4 has a slot on the bottom of it that rests on that
ridge. The log also has a notch on the front of it that rests against the furthest right log grate finger (see below).
The upper portion of the log rests against the right edge of the rear burner.
Log #5
Place log #5 as shown below. The notch on the bottom of log #5 rests on the left side of the log grate with the cut
end of the log resting to the left of the grate. Push log #5 all the way backword. The top of log #5 rests against
the back wall of the firebox (or fireback if used) as shown below.
Slot on bottom of log #4
Ridge on
front RT
burner
Upper portion of log
rests on RT edge of
rear burner
Notch on front log
rests against grate
Top of log
rests against
back wall

PB42 CF BonFyre
(sku# 94500772)
Page 7 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Log #6
Place log #6 as shown below. The notch on the bottom of log #6 rests against the furthest left log grate finger
and the upper portion of the log rests against log #2 (see below).
Log #7
Place log #7 as shown below. There is a notch on the lower left of the log. The notch fits over the right side of
the second log grate finger from the right. The upper portion of log #7 rests against log #2 as shown below.
Top of log #5 rests
against log #2
Notch on log #5
rests againt log
grate finger
View from front View from right

PB42 CF BonFyre
(sku# 94500772)
Page 8 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Log #8
Place log #8 as shown below. Log #8 has a notch that aligns the log with the center finger of the log grate.
The top portion of log #8
rests against log #7. The
limb on log #7 helps to
lock log #8 into place
(see right).
log #7
log #8

PB42 CF BonFyre
(sku# 94500772)
Page 9 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
Log #9
Place log #9 as shown below. Log #9 has a slot on the bottom right that engages a bracket that extends off the
back of the furthest right log grate finger, behind log #4. . The top of log #9 rests in a branch “Y” on log #7 (see
lower pictures below).
Log #10
Place log #10 as shown below. The right side of log #10 should contact the second log grate finger from the right.
The upper portion of the log angles slightly left and rests on the front burner without obstructing any burner holes
(see below).
Slot on left front of log #9 rests
on a bracket behind log #4. View of the
bottom of log
#9 in place.
View of the top of log #9
resting in “Y” on log #7
log #9
log #7
log #9
Rests against
log grate finger

PB42 CF BonFyre
(sku# 94500772)
Page 10 of 10 17602206 — 5/3/21 © Travis Industries, Inc.
(94500772) BonFyre - Log Replacement Part Numbers
Log
#1 250-05744
Log
#6 250-05749
Log
#2 250-05745
Log
#7 250-05750
Log
#3 250-05746
Log
#8 250-05751
Log
#4 250-05747
Log
#9 250-05752
Log
#5 250-05748
Log
#10 250-05753