First Data FD-400GT-CDMA User manual

XAC Automation Corporation
886-3-577-2738
www.xac.com.tw
The above information is the exclusive intellectual property of XAC Automation Corporation
and shall not be disclosed, distributed or reproduced without permission of XAC Automation
Corporation.
XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or
errors made herein; nor for incidental or consequential damages resulting from the furnishing,
performance or use of his material.
This document contains proprietary information protected by copyright. All rights are reserve.
PORTABLE TERMINAL
FD-400GT-CDMA
INSTALLATION GUIDE


1. BEFORE STARTING
There are two holes under a plastic cover on the left side of
terminal (Figure 1). One is a power jack; the other is an USB
programmable port (Figure 2). Rechargeable battery is on the back
side of terminal (Figure 3).
Adapter spec:
DELTA_ADP-36JH B
Input: 100-240Vac, 50/60Hz 1A; Output: 12Vdc, 3A
Car Charger:
EDAC POWER ELECRONICS CO., LTD. / ED1025
Input: 11-16Vdc, 5A; Output: 12Vdc, 2.5A
Operating Temperature: 0oC to 40oC
Battery pack: CHENG UEI / FD400 7.4V, 2.3Ah
RTC battery spec: 3V, CR2032
Caution: The cover (Figure 3) shall be provided with a means to
keep it closed during normal operation.
Caution: Risk of explosion if the battery is replaced by an
incorrect type. Please dispose of used battery according to the
instructions.
Warning: A shielded-type power cord is required in order to meet
FCC emission limits and also to prevent interference to the nearby
radio and television reception. It is essential that only the supplied
power cord be used.
2. POWER ON THE TERMINAL
Install the battery, or plug the power cord into the power jack and
plug the power adapter into a 120-volt electrical outlet or into a
surge suppressor (recommended) after the power cord is
connected to the power adapter. Press the power button at the
front of device (Figure 4) until the system is booted up.
3. LOADING THE PAPER
Gently pop the printer cover’s latch to open the cover (Figure 5);
then lift the cover.
Load a roll of thermal paper (Appleton 1012 recommended) into
the printer (Figure 6). Load it so that the print-side of the paper
will feed out facing the operator.
Close the cover by pressing down evenly on both side tabs, or by
pressing on the center of the printer cover.
Use the serrated bar to tear off any excess paper.
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Warning: If the device, FD400GT, is used without the detachable privacy shield, the
following criteria needs to be met by the Installed Environment of the PED for complying
with the PCI privacy screen design requirement:
A. Positioning of the PED on the check-stand in such way as to make visual
observation of the PIN-entry process infeasible.
Visual shields designed into the check-stand.
Position the PED so that it is angled in such a way to make PIN spying
difficult.
B. Pop-up (temporary) privacy shield attached to the PED mounting stand.
Consumer (through education & prompting) or merchant would put the shield in
place during PIN entry.
C. Installing PED on an adjustable stand that allows consumers to swivel the
terminal sideways and/or tilt it forwards/backwards to a position that makes
visual observation of the PIN-entry process difficult.
D. Positioning of in-store security cameras such that the PIN-entry keypad is not
visible.
E. Instructing the cardholder regarding safe PIN-entry, done with a combination of:
Signage on the PED.
Prompts on the display, possibly with a "click-through" screen.
Potentially literature at the point of sale.
A logo for safe PIN-entry process.
Table A1: Matrix of Observation Corridors and PIN Protection Method
Observation Corridors
Method Cashier
Customers
in Queue Customers Elsewhere On-Site Cameras Remote Cameras
PED Stand A M H L L L
PED Stand B H H H L M
Check-Stand A L M M L H
Check-Stand B H H M H H
Customer Instruction H* H* H* H* H*
zCustomer Instruction methods are less repeatable and therefore should be used in
combination with other methods. L= low, M= medium, H= high.

4. USING THE MAGNETIC CARD READER
Find the reader slot in the middle of surface. Swipe card through
slot from left to right or the opposite direction with stripe lies
down and facing the display (Figure 7).
5. USING THE CONTACTLESS CARD READER
Contactless reader antenna is around the display and PIN pad. It
will light up with blue color signal when FD400GT is powered on
and that means reader is working normally.
Put contactless card to approach the antenna of card reader
(Figure 8) for reading the card data during transaction.
6. USING THE KEY PAD
To enter numbers or letters, simply press the appropriate key. For
example, to type the letter A: Press [ALPHA], then [A] (the Void
key) (Figure 9).
Caution: Use only shielded signal cables to connect I/O devices to this
equipment. You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Figure 7
Figure 8
Figure 9
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
IMPORTANT NOTE: IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de
distance entre la source de rayonnement et votre corps.
Warning: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.