Fisher-Price B1637 User manual

w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Model Number: B1637
PLEASE KEEP FOR FUTURE REFERENCE.
Please read these instructions before assembly and use of this product, as they contain important information.
Adult assembly is required.
Tools needed for assembly: Phillips Screwdriver and Scissors (both not included).
Requires four “D” (LR20) alkaline batteries for swinging and sound operation;
three “AA” (LR6) alkaline batteries for sound ‘n lights tray operation; and
three “AAA” (LR03) alkaline batteries for remote operation (all batteries not included).
Maximum Weight Limit: 24 lbs. (10.9 kg).
IMPORTANT! The maximum weight limit for this product is 24 lbs. If your child weighs
less than 24 lbs., but is really active and appears to be able to climb
out of the swing, immediately discontinue its use.
Deluxe Quick Response Swing
with Remote Control

2
Occasionally a consumer may experience a problem with
one of our products. If this should happen, please call us
toll-free, rather than return this product to the store. Usually,
we can solve the problem over the telephone or send you
replacement parts. Please call Fisher-Price® Consumer
Relations, toll-free at 1-800-432-5437,8AM - 6 PM EST
Monday through Friday. Hearing-impaired consumers using
TTY/TDD equipment, please call 1-800-382-7470.
Or, write to:
Fisher-Price®
Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
•To prevent serious injury or death
from falls and being strangled in
the restraint system:
- Always use the restraint sys-
tem. Never rely on the tray to
restrain child.
- Never use with an active child
who may be able to climb out of
the seat.
•Never leave child unattended.
WARNING
This product contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
Consumer InformationWa rnings and Caution

Parts
3
Front Base
Rear Base
Housing
2 Rear Legs
(Shorter)
Motor Housing
Seat with Restraint
2 Seat Tubes
Bracket
(with M4 Lock Nuts)
Seat Wire
2 Seat Wire
Caps
2 Accessory Bins
Pad
Sound ‘n
Lights Tray
Mirror Base
Remote Control
and Holder
(with M4 Lock Nut)
Tray
2 Front Legs
(Longer)
M4 Screw - 4
Shown Actual Size
Note: Tighten or loosen all screws and bolt with a Phillips screwdriver. Do not over-tighten the screws.
#8 x 13/8" Screw - 10
Shown Actual Size
#6 x 5/8" Screw - 4
Shown Actual Size
M4 Bolt - 1
Shown Actual Size

•Place the front base on a flat surface.
•Position a front leg (longer) so that the tapered end is
downward, as shown.
•While pressing the button on one of the front legs, insert it
into the front base. Push down on the front leg until the
button “snaps” into the hole in the front base.
•Repeat this procedure to assemble the other front leg to
the front base.
Front Base
Tapered End
Tapered End
Front Legs
(Longer)
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
Assembly
•Using scissors, remove the ribbon connecting the remote
and the holder.
4
Press
Button
Press
Button
Remote
Holder
Ribbon
1
•While standing on the front base, pull the front legs up.
The front legs should remain secured to the front base.
If you can remove the front legs, you have not assembled
them correctly to the front base. Reread and repeat
assembly step 1.
Front Legs Pull Up
Pull Up
Front Base
2
3
•Position the holder so that the
open end faces forward, as shown.
•Slide the holder onto the front leg with a hole.
Holder
Front
Leg Hole
4
Shown Actual Size
M4 Lock Nut
Rounded
Side
M4 Lock Nut
(Rounded
Side Out)
Hexagonal Opening
Hint: An M4 lock nut has been assembled to the holder at
the factory. During shipment of this product, it may have fallen
out. Check to be sure there is a lock nut in the hexagonal opening
on the holder. If it has fallen out, fit the lock nut back into the
hexagonal opening. Make sure the rounded side of the lock nut
faces out.

Assembly
5
• Position a rear leg so that the tapered end is upright.
•While pressing the button on the top of the rear leg, insert it
into the housing short tube, as shown. Push the rear leg until
the button “snaps” into the hole in the short tube.
•Repeat this procedure to assemble the other rear leg to the
motor housing short tube.
•Pull the rear legs down to be sure they are secure in the
housings. If you can remove them, you have not assembled
them correctly. Please re-read and repeat this assembly step.
Button
Rear Legs
Motor Housing
Short Tube
•Fit the bottom of the remote into the cupped portion of
the holder.
•Push to “snap” the top of the remote under the holder clips.
Holder
6
•Position the holder so that the hole in the holder aligns with
the hole in the front leg.
•Insert the M4 bolt through the holder, front leg and into the
lock nut. Tighten the bolt.
Holder
Front Leg
5
8
Tapered
End
• Position the housing so that the hub is inward.
•While pressing the button on the top of a front leg, insert it
into the housing slot, as shown. Push the front leg until the
button “snaps” into the hole in the housing.
•Repeat this procedure to assemble the motor housing to
the other front leg.
•Pull the front legs down to be sure they are secure in the
housings. If you can remove them, you have not assembled
them correctly. Please re-read and repeat this assembly step.
Press
Buttons
Front
Legs
Motor
Housing
Hole
Housing Hub
Slot
7
Clips
Remote
M4 Bolt
Shown Actual Size

•Place the rear base on a flat surface so that the buttons
face the front base.
•While pressing the buttons on each side of the rear base,
fit the rear legs onto the rear base. Push the rear legs down
until the buttons on the rear base “snap” into the holes
in each rear leg.
Rear Base
Front
Base
Rear
Legs
Assembly
•While standing on the rear base, pull the rear legs up.
They should remain secured to the rear base. If you can
remove the rear legs, you have not assembled them cor-
rectly to the rear base. Reread and repeat assembly step 10.
•Set the frame assembly aside for Assembly step 21.
•Position the seat face down, with
the top of the seat facing you.
•Position a seat tube so that the long
end is upright and toward you and the curved end is toward
the outside edge of the seat.
•Insert the curved end of the seat tube through the holes in
the ridges on the seat back.
•Repeat this procedure to assemble the other seat tube to
the seat.
6
Press
Button
Press
Button
Rear Legs
Pull Up
Pull Up
Rear Base
10
11
12
Top of Seat
Seat Tube
Long Ends
Ridges
Curved
End
•Pull both rear legs out until they “snap” into place.
Pull
Rear
Leg
Pull
Rear
Leg
9

•Insert four M4 screws into the seat tubes and tighten.
Assembly
•Rotate the seat tubes down.
•Fit the seat wire through the slot in the bracket as shown.
7
Seat
Tubes
14
Bracket
Bracket Slot
Seat Wire
Seat Tubes
15
16
•Position the bracket so that the tall end is toward the
bottom edge of the seat.
Hint: The M4 lock nuts have been assembled to the bracket at
the factory. During shipment of this product, they may have
fallen out. Check to be sure there is a lock nut in each hexagonal
opening on the bracket. If one (or more) has fallen out, fit the lock
nut into a hexagonal opening in the bracket. Make sure the
rounded side of the lock nut is facing up.
•Fit the grooves on the bracket to the seat tubes, as shown.
Seat
Tubes
Bracket
Grooves
Tall
End
Bottom
Edge of
Seat
13
M4 Screw - 4
Shown Actual Size
Lock Nut
Hexagonal
Opening
Shown Actual Size
M4 Lock Nut
Rounded Side

•While holding the seat wire in place, carefully turn the
seat around so that the front of the seat faces you.
•Position the seat wire cap so that the rounded edge
is upright.
•Fit each end of the seat wire through the hole in each
seat wire cap.
Ends of
Seat Wire
Assembly
•Turn the seat face down.
•Fit an accessory bin into the groove on each side of the
seat, as shown.
•Insert two #8 x 13/8" screws into each accessory bin
and tighten.
8
Seat Wire
Cap
Seat Wire
Cap
Grooves
Seat
Accessory Bin
Accessory Bin
18
20
•Lift the seat tubes slightly.
•With the seat wire hanging down, insert the ends of the seat
wire through the slots in the seat, as shown.
Slots
Seat Wire
17
#8 x 1
3/8
”Screw - 4
Shown Actual Size
Seat Wire
Cap Hole
Rounded Edge Up
19
•Press the seat wire caps
into place.
•Insert two #6 x
5/8"
screws
through each seat wire cap
and tighten.
Seat Wire
Caps
Seat Wire is
Through Hole in
Seat Wire Cap
Press in Place
#6 x 5/8" Screw - 4
Shown Actual Size
Hint: The seat wire caps are designed to fit into the seat only one
way. If the screw holes in the seat wire caps do not align with the
holes in the seat, try switching the seat wire caps onto the
opposite ends of the seat wire.

Assembly
•Fit the pocket on the back of the pad onto the seat back.
•Fit the waist belts through the smaller slots in the pad.
9
Waist Belts
Pad
Slot
Slot
23
•Lift the bottom of the pad.
•Insert the pad elastic loops through the holes in the
seat bottom.
•Insert the crotch belt through the slot in the pad.
•From under the seat, fit the elastic loops onto the tabs on
the seat bottom.
24
•Insert a #8 x 13/8" screw into each frame hub and tighten.
•Again, push down on the seat to be sure the seat is secured
to both frame hubs.
Frame
Hubs
22
Pad
Elastic
Loops
Holes
Crotch
Belt
•Position the seat assembly so that the front of the seat is
toward the curved front base.
•While pressing the buttons on the swing tubes, insert them
into the frame hubs. Push the swing tubes up until the
buttons “snap” into the hole in the frame hubs.
•Push down on the seat to be sure the seat is secured in
both frame hubs.
Swing
Tube
Front
of Seat
Curved
Front
Base
Push
Button
Frame Hub
21
Seat Bottom
#8 x 1
3/8
”Screw - 2
Shown Actual Size

10
•Position the lights ‘n sounds tray on a flat surface, with the
roller facing you.
•Position the mirror base, with the mirror toward you.
•Fit the mirror base onto the lights ‘n sounds tray.
26
•Turn the assembly over. Insert four #8 x 13/8" screws into the
bottom of the lights ‘n sounds tray and tighten.
Assembly is now complete.
27
Mirror Base
Lights ‘n
Sounds Tray
•Fit the bottom edge of the pad around the bottom edge
of the seat.
•Hook the elastic loops on each side of the pad to the peg
on the back of the accessory bins.
25
Elastic
Loop
Elastic
Loop
#8 x 1
3/8
”Screw - 4
Shown Actual Size
Battery Installation
•Locate the battery compartment door on the swing frame.
•Insert a coin into the battery compartment door and pry the
battery compartment door off of the swing frame.
•Insert four “D” (LR20) alkaline batteries as indicated inside
the battery compartment.
•Replace the battery compartment door.
Battery
Compartment
Door
Swing
Hint: When swinging, sound or power L.E.D. slows/dims/stops,
it’s time to replace the batteries! We recommend using alkaline
batteries for longer battery life.
AssemblyAssembly