Fisher-Price Caring Touch High Chair User manual

Instructions
Caring Touch
™
High Chair
Model Number 71777
Doll not included.
Please save these instructions for future reference.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver.

Message to Parents
Thank you for choosing the Fisher-Price Caring Touch™ High Chair for your child. Your little parent-
in-training will delight in turning up the pretend heat to "warm" a bottle while spoon feeding dolly some
specially prepared baby "food" from the magic food processor. We hope that your child will spend
hours of imaginative play with this special toy.
Important Notes:
• All plastic food toys and food contact surfaces should be hand washed thoroughly with warm soapy
water before use.
• Do not allow your child to sit in the high chair.
Parts Diagram
2
Tray
Left Leg
Seat Back
Spoon
Bottle
Baby Food Jar
Right Leg
Seat
Base
CAUTION
Please keep small parts and plastic
bags out of children’s reach. Dispose
of plastic bags properly.
#6 x 11/2" Screw - 2
Shown Actual Size
#6 x 3/4" Screw - 8

Assembly
• Position the right leg on a flat surface with the
shelf facing down as shown.
• With the scalloped edge toward you, insert the
knobs on the side of the base into the holes in
the right leg.
• Insert two #6 x 3/4" screws through the base
and into the right leg.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• With the scalloped edge toward you, insert the
knobs on the side of the seat into the holes in
the right leg.
• Insert two #6 x 11/2" screws through the seat
and into the right leg.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• Position the left leg on a flat surface, decorated
side down.
• Insert the knobs on the side of the base and
on the side of the seat into the holes in the
left leg.
• Insert two #6 x 3/4" screws through the base
and into the left leg.
• Insert two #6 x 3/4" screws through the seat and
into the left leg.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Holes
Base
Knobs
Knobs
Left Leg
Seat
3
Holes
Shelf
Holes
Knob
Knob
Knob
Knob
Scalloped
Edge
Right Leg
Scalloped Edge
Base
Seat

Assembly Feeding Time!
Questions?
• Position the seat back so that the "cushion"
side faces you.
• Align the ridge on each side of the seat back
with the groove in each side of the high chair.
• Press down firmly until the seat back is flush
with the seat.
• Insert two #6 x 3/4" screws through the holes
under the seat and into the seat back.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Groove
Ridge
Seat Back
• Fit the grooves in the tray onto the high chair
arms.
• Slide the tray into place.
Assembly is now complete. Time for dolly's
dinner!
• Place the bottle in the pretend warmer and
turn the knob.
• Place the food processor on the magic mixer
and press down to prepare dolly's meal!
• Slide the tray off and on the high chair arms,
just like a real high chair.
Groove
Printed in Mexico.
©1997 Fisher-Price, Inc., East Aurora, New York 14052
We'd like to hear from you!
Call Fisher-Price Consumer Affairs, toll-free at
1-800-432-KIDS, 8 AM - 6 PM EST Monday
through Friday. Hearing-impaired consumers using
TTY/TDD equipment, please call 1-800-382-7470.
Or, write to: Fisher-Price Consumer Affairs,
636 Girard Avenue, East Aurora, New York 14052.
If you have any questions about this product:
In Canada, call 1-800-567-7724, or write to:
Mattel/Fisher-Price, 6155 Freemont Blvd., Mississauga,
Ontario L5R 3W2.
In Great Britain, telephone [phone].
In Australia, call the Fisher-Price Australian Consumer
Advisory Service toll-free at 1-800-800-812, or write to:
Fisher-Price, Mattel Pty. Limited, 461 Plummer Street,
Port Melbourne, Victoria 3207.
Hole
3/4" Screws
Magic
Mixer
Food
Processor
Knob
Pretend
Warmer
Bottle