Fisher-Price CFM96 User manual

1
CFM96
fisher-price.com
Keep this instruction sheet for future reference,
as it contains important information.
Requires four C (LR14) alkaline batteries (not included) for operation.
Adult assembly is required. Tool required: Phillips screwdriver (not included).
Wipe this toy with a clean, damp cloth. Do not immerse.
This toy has no consumer serviceable parts. Do not take apart.

2
Consumer Information
CO
N
SU
MER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
FCC STATEMENT (UNITED STATES ONLY)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.This
equipment generates uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.However, there is no
guarantee that interference will not occur
in a particular installation.If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced radio/TV
technician for help.
NOTE: Changes or modifications not expressly
approved by the manufacturer responsible for
compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
©2015 Mattel. All Rights Reserved. CFM96-0970
PRINTED IN MEXICO 1100472922-DOM
CAN ICES-3 (B)/NMB-3 (B)
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that
may cause undesired operation of the device.
L’utilisation de ce dispositif est autorisée
seulement aux conditions suivantes : (1) il ne
doit pas produire de brouillage et (2) il doit
pouvoir tolérer tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de
compromettre son fonctionnement.

3
Assembled Parts
CAUTION
This package contains small parts.
For adult assembly only.
Arch
Base
2 Narrow Braces
(left and right)
2 Walls
(left and right)
2 Wide Braces
(left and right)
Lower Ramp
Upper Ramp
#8 x ¾" (1,9 cm) Screw - 20
SHOWN ACTUAL SIZE
Tighten and loosen all screws
with a Phillips screwdriver.
Do not over-tighten screws.

4
Assembly
1
2
3
• Turn the arch over so the battery door is facing up. Position a wall so the foot is facing up.
• Fit three of the pegs on a wall into the loop and notches in the arch.
Hint: The wall is designed to fit one way. If it does not seem to fit, try the other wall.
• Fit a narrow brace to the posts on the wall.
Hint: Each narrow brace is designed to fit one way. If it does not seem to fit, try the other
narrow brace.
• Insert three screws into the holes in the narrow brace and tighten.
Arch Battery Door
Arch Notches
Arch Loop
Foot
Arch Wall
Narrow Brace

5
4
5
6
• Fit the sockets on a wide brace to the sockets on a wall.
Hint: The wide brace is designed to fit onto the wall one way. If the wide brace does not seem to
fit, try the other wide brace.
Wide Brace
Assembly
• Insert five screws into the holes in the wide brace and tighten.
• Repeat assembly steps 1-5 to attach the other wall, narrow brace and wide brace to the arch.
Wall Wide Brace Narrow Brace