Fisher-Price FYK61 User manual

FYK61
Keep this instruction sheet for future reference,
as it contains important information.
Requires four AA (LR6) alkaline batteries (included). Batteries included are for
demonstration purposes only.
Required tool for battery replacement: Phillips screwdriver (not included).
Only adults should install batteries.
To clean, wipe with a damp cloth. Do not immerse.
Press Sloth’s feet
buttons to play and learn
together. Dance, clap and
sing-along with Sloth!
Kee
p
this instruction sheet for future reference,
as
i
t
co
nt
ai
ns
i
mp
or
ta
nt
inf
or
ma
ti
on
Pr
ess
Sl
ot
h’
s
fe
et
b
uttons to p
l
ay an
d
l
earn
t
ogether. Dance, clap an
d
si
ng-a
l
ong w
i
t
h
S
l
ot
h
!

BATTERIES AND POWER
Battery Safety Information
In exceptional circumstances,
batteries may leak fluids that can cause
a chemical burn injury or ruin your
product. To avoid battery leakage:
•Do not mix old and new batteries
or batteries of different types:
alkaline, standard (carbon-zinc)
or rechargeable.
•Insert batteries as indicated inside
the battery compartment (+ and -).
•Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the product. Dispose
of batteries safely. Do not dispose of
this product in a fire. The batteries
inside may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or
equivalent type, as recommended.
•Do not charge non-rechargeable
batteries.
•Remove rechargeable batteries from
the product before charging.
•If removable, rechargeable batteries
are used, they are only to be charged
under adult supervision.
Protect the environment by not
disposing of this product or any
batteries with household waste.
This symbol indicates that this product
shall not be treated as household waste.
Check your local authority for recycling
advice and facilities.
•Loosen the screw in the battery
compartment door and remove the
door. Remove the exhausted batteries
and properly dispose.
•Insert four, new AA (LR6)
alkaline batteries.
•Replace the battery compartment
door and tighten the screw.
•Slide the power-volume switch to
ON with low volume, ON with
high volume or OFF.
•When sounds, lights or motion
become faint, slow or stop, it’s time
for an adult to change the batteries.
•If this toy begins to operate
erratically, you may need to reset the
electronics. Slide the power-volume
switch off and then back on again.
For longer life, use alkaline batteries.
1,5V x 4
AA (LR6)

MORE FUN WITH MORE THAN ONE!
Each sold separately and subject to availability.
Here’s how to sync your Linkimals™!
1Turn power OFF on each toy.
2Now turn power ON.
3Watch and listen to Linkimals respond to each other in fun ways during play!
Uh-oh! If, at any time, one of your Linkimals doesn’t seem to be interacting with
the other Linkimals, turn all of them OFF and then back ON again.
Linkimals are also available in different languages (sold separately and subject
to availability). Linkimals only sync with other Linkimals of the same language.

©2019 Mattel. FYK61-0970
PRINTED IN CHINA 110205634-DOM
FCC STATEMENT (UNITED STATES ONLY)
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the
equipment and receiver.
•Consult the dealer or an experienced
radio/TV technician for help.
NOTE: Changes or modifications not expressly
approved by the manufacturer responsible for
compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
UNITED STATES: 1-800-432-5437.
Fisher-Price, Inc., 636 Girard Avenue,
East Aurora, NY 14052.
GREAT BRITAIN: Mattel UK Ltd, Vanwall
Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303;
www.service.mattel.com/uk.
Mattel Europa B.V., Gondel 1, 1186 MJ
Amstelveen, Nederland.
CANADA: 1-800-432-5437.
Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2.
AUSTRALIA: Mattel Australia Pty. Ltd.,
658 Church Street, Locked Bag #870,
Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
NEW ZEALAND: 16-18 William Pickering
Drive, Albany 1331, Auckland.
ASIA: Mattel East Asia Ltd., Room 503-09,
North Tower, World Finance Centre,
Harbour City, Tsimshatsui, HK, China.
Tel.: [phone].
MALAYSIA: Diimport & Diedarkan Oleh:
Mattel Southeast Asia Pte. Ltd., No
19-1, Tower 3 Avenue 7, Bangsar South
City, No 8, Jalan Kerinchi, 59200 Kuala
Lumpur, Malaysia. Tel: [phone].
SOUTH AFRICA: Mattel South Africa
(PTY) LTD, Oce 102 I3, 30 Melrose
Boulevard, Johannesburg 2196.
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions: (1) This device may not cause
interference. (2) This device must accept any
interference, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) L’appareil ne doit
pas produire de brouillage; (2) L’appareil doit
accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement