Fisher-Price GO DIEGO GO K6673 User manual

Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tools required for assembly: Phillips Screwdriver,
Hammer and Scrap Block of Wood (not included).
Age: 2-5 years
Weight limit: 55 lbs (25 kg).
www.fisher-price.com
K6673

Seat
2 Fork Covers
Front Wheel Assembly
Fork
Frame
Handlebar Back
Straight
Axle
2 Bushings
2 Wheel Hubs 2 Wheel Caps
Note: Some parts shown are assembled
to both sides of the trike.
IMPORTANT!
• Please save all packaging material until assembly is
complete to ensure that no parts are discarded.
• Please wipe each part with a clean, dry cloth
before assembly.
*We’ve included one extra .354" cap nut for your convenience.
Note: Tighten and loosen the screws with a Phillips screwdriver.
Do not over-tighten the screws.
4 Pedal Hubs
WARNING CAUTION
To avoid serious injury:
• Adult supervision is required.
• Never use near cars and other motor
vehicles, near streets, steps, sloped
driveways, hills, roadways, alleys, swimming
pool areas or other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
This product contains small parts
in its unassembled state.
Adult assembly is required.
2 Rear Wheels
Part not shown: Label Sheet
ALL SHOWN ACTUAL SIZE
Handlebar Front
2
Consumer Information
#8 x 2¼" Screw - 1
#8 x ¾" Screw - 6 .354" Cap Nut - 2*
.354"

Frame
Seat
PUSH
Wheel Hub
(Flat Side Down)
Bushing
(Grooved Side Down)
Straight Axle Assembly
Bottom View
• Place one end of the straight axle into the cap nut.
Tap the end of the straight axle with a hammer.
Make sure the cap nut is securely attached to the
straight axle.
• Slide a wheel hub,
at side down , onto the straight axle.
• Slide a rear wheel, indented side down , onto the
straight axle.
• Slide a bushing, grooved side down , onto the
straight axle.
• Turn the frame upside down.
• Insert the straight axle assembly through the holes in
the rear of the frame.
• Turn the assembly upright.
• Slide a bushing, smooth side rst , onto the end of the
straight axle.
• Slide a wheel, at side rst , onto the end of the
straight axle.
• Slide a wheel hub, pointed end rst , onto the end of
the straight axle.
• Fit the seat onto the frame.
• Push rmly near the back end of the seat to "snap" it
into place.
Straight
Axle
Cap Nut
Bushing
(Smooth Side First)
Wheel Hub
(Pointed End First)
Wheel
(Flat Side First)
Straight Axle
Rear
Wheel
(Indented
Side Down)
13
4
2
3
Assembly
Straight
Axle

• Fit the tabs on the wheel cap into the slots in the
wheel hub. Push to "snap" the wheel cap in place.
• Repeat this procedure to attach the other wheel cap
to the other wheel hub.
• Fit two pedal hubs onto the pedal axle tabs. Make sure
the tabs t into the slot in each pedal hub.
• While holding the pedal hubs on the pedal axle,
insert the pedal axle into the hole in the center of the
front wheel.
• Press the pedal hubs into the center of the front wheel
until they are ush with the surface of the front wheel.
• Repeat this procedure for the other two pedal hubs on
the other side of the front wheel assembly.
• Fit the cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel to be sure the cap nut is securely attached
to the straight axle.
Hint: You may need the help of another adult to hold
the other end of the straight axle in place.
Wheel Hub
Wheel Cap
Pedal Hub
Pedal Hub
5
7
6
4
Pedal Axle Tab
Assembly
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle ts into the groove at the
bottom of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x ¾" screws into the fork cover
and tighten.
• Repeat this procedure to attach the other fork cover
to the other fork arm.
Fork Arms
Pedal Axle
Groove
Fork Cover
Front Wheel
Assembly
8

Fork Post
Fork Covers
• Insert the fork post up through the hole in the neck of
the frame. Make sure the fork is positioned so that the
fork covers face the rear wheels.
REAR OF TRIKE
• Fit the handlebar front to the fork post.
Hint: The handlebar front is designed to assemble to
the fork post one way.
• Fit the handlebar back to the fork post and handlebar
front. Hold them together rmly.
• First, insert the remaining #8 x ¾" screws through the
outer holes in the handlebar back and tighten.
• Then, insert the #8 x 2¼" screw through the center
hole in the handlebar back and tighten.
Handlebar Front
¾" Screw
¾" Screw
2¼" Screw
Handlebar Back
9
10
Fork Post
5
• Wipe the vehicle with a clean, dry cloth to remove any
oils before applying labels.
• Apply labels exactly as shown in the illustrations. For
best results, avoid repositioning the label after it has
been applied.
• Starting at the center of a label rub rmly with a dry
cloth, and smooth towards the outer edges to remove
air bubbles.
Right Side
7
8
4
3
Left Side
6
3
5
2
1
Label DecorationAssembly

IMPORTANT! It is a good practice to start training
children very young regarding the importance of helmet
use. When children are older and riding bicycles and
faster vehicles, it is important that they use a helmet
each and every time they ride. For this reason, even
while riding a tricycle, it is a good idea to familiarize
your child with helmet use, so that it becomes a habit
for life. Choose a helmet that complies with requirements
of the applicable certifying agency for bicycle helmets.
Consumer Information
• Periodically, check the plastic parts and if broken or
cracked, dispose of them properly.
• Periodically, check all fasteners regularly to be sure
they are tight. If the fasteners are not tight, tighten
them as necessary.
• To clean, use a mild soap and water solution and
a clean cloth. Rinse clean with water to remove
soap residue.
Care
©2010 Viacom International Inc. Nickelodeon, Nick Jr., Dora the Explorer and all
related titles, logos and characters are trademarks of Viacom International, Inc.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. Inc., unless otherwise indicated.
PRINTED IN MEXICO K6673b-0920
CO
N
SU
MER
ASS
I
S
T
A
N
C
E
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.