PARTS
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Protect the environment by not disposing of this
product with household waste (2012/19/EU).
Check your local authority for recycling advice
and facilities.
Flight Tower Arm
2 Tower Bases
Extra Copter
Blade
M4,2 x 26,3 mm Bolt - 1 M3 x 10 mm Screw - 2
FASTENERS SHOWN ACTUAL SIZE
Tighten and loosen all screws with a Phillips screwdriver.
Do not over-tighten.
Wayne Tower
©2016 Mattel. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, except as noted. DNY07-0970
PRINTED IN CHINA 1101215663-DOM
Flight Tower
• Locate the battery compartment door on the end of the
flight tower arm and the back of Wayne Tower.
• Loosen the screws in the battery compartment doors and
remove each door.
• Insert two, new AA (LR6) alkaline batteries in Wayne
Tower and four, new AA (LR6) alkaline batteries in the
flight tower arm.
• Replace the battery compartment doors and tighten
the screws.
• If this toy begins to operate erratically, you may need to
reset the electronics. Slide the power switch on the flight
tower arm off and back on. Remove the batteries from
Wayne Tower and reinstall.
• When sounds/light/motion become faint or stop, it’s time
for an adult to change the batteries.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of this product in a fire. The
batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to
be charged under adult supervision.
CAN ICES-3 (B)/NMB-3 (B)
This device complies with Industry Canada licence-exempt
RSS-210.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
CE DISPOSITIF EST CONFORME À LA NORME CNR-210
D'INDUSTRIE CANADA APPLICABLE AUX APPAREILS RADIO
EXEMPTS DE LICENCE.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes : (1) il ne doit pas produire de brouillage
et (2) il doit pouvoir tolérer tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de compromettre
son fonctionnement.
FCC STATEMENT (UNITED STATES ONLY)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
NOTE: Changes or modifications not expressly approved by
the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Flight Tower Arm
Wayne Tower
