Fisher-Price DJD81 User manual

1
DJD81
OWNER’S MANUAL
IMPORTANT! KEEP FOR FUTURE REFERENCE.

2
BEFORE YOU BEGIN
IMPORTANT!
Please keep these instructions for future reference. Please read these
instructions before assembly and use of this product.
Before assembly and each use, inspect this product for damaged hardware,
loose joints, missing parts or sharp edges. Do not use the product if any
components are broken or missing.Do not use replacement parts other than
those approved by the manufacturer or distributor.
Adult assembly is required. No tools required for assembly.
The tray is not microwave safe.
Before first time use, wash the tray thoroughly with soap and water.
To clean the frame and toys, wipe clean using a mild cleaning solution and
damp cloth.
Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with
water to remove soap residue.
The tray is top rack dishwasher safe (or use the bottom rack - without using
the drying cycle).
Machine wash the pad in cold water on the gentle cycle. Do not use bleach.
Tumble dry on low heat.
To remove the pad, lift to remove the pad pegs from the front base. Then
remove the pad button holes from the pegs underneath the seat ring.
To replace the pad, follow the assembly steps.
WARNING
To prevent serious injury or death:
• It is dangerous to use this product on an elevated surface, e.g. a table.
• Suffocation Hazard – Never use on a soft surface (bed, sofa, cushion), since the
product can tip over and cause suffocation in soft surfaces.
• Never leave the child unattended. Always keep child in view while in product.
• Never use near steps.
• Strings can cause strangulation! DO NOT place items with a string around child’s
neck, such as hood strings or pacifier cords.
• Never use as a carrier or lift while child is seated.
• Use only with a child who is able to hold head up unaided and who is not able to
climb out or walk.

3
ASSEMBLED PARTS

4
1
2
Hub Button Out
Hub Button Out
ASSEMBLY
The frames and the front base
are designed to fit one way.
If these parts do not “snap”
together, try fitting each frame
into the opposite socket in the
front base.
3

5
ASSEMBLY
4
Pull on the rear base to be sure
it’s attached.
5
6

6
7
8
If you cannot “snap” the parts into place,
you may have assembled the seat ring
backwards. Remove the seat ring from the
frames and turn it around so that the wider,
flat side is toward the front base. Then,
repeat this assembly step.
ASSEMBLY
9
Fit the end of the pad with
the pegs down through the
seat ring.

7
ASSEMBLY
10
Fit the eight buttons holes on
the pad to the eight pegs under
the seat ring.
11
12
Press the ends of the
latches and lift the tray
to remove.

8
Linkable, Removable Toys
Fit the link on each toy to a loop on
the seat.
Placing and Removing Baby
Place the assembled product on the floor.
Kneel or stand behind the seat and fit or
remove baby’s legs into or from the leg
openings in the seat pad. Carefully lower
or lift baby into or out of the seat.
FABRIC SEAT HELPS BABY SIT UP!

9
OPENING THE FRAME
Lift the frames until each
“snaps” into place. Push down
on the seat ring to be sure the
frame is open.
2
While pressing the button on
each hub, lower the seat.
CLOSING THE FRAME
1
Fit the posts on the tray to the
underside of the frame sockets
for storage.

©2020 Mattel. DJD81-KM72
PRINTED IN CHINA 1100693145-UU1
Great Britain: Mattel U.K. Limited,
The Porter Building, 1 Brunel Way, Slough SL1 1FQ, UK.
www.service.mattel.com/uk.
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen,
Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd., Room 503-09, North Tower, World Finance
Centre, Harbour City, Tsimshatsui, HK, China. Tel.: [phone].
Malaysia: Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level
19, Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala
Lumpur, Malaysia.
South Africa: Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose
Boulevard, Johannesburg 2196.