Fisher-Price N1891 User manual

1
www.fisher-price.com
N1891
Please keep this instruction sheet for future information, as it contains
important information.
Adult assembly is required.
Requires three “AA” batteries (included) for operation.
Tool required for battery replacement: Phillips screwdriver (not included).

2
Assembled Parts
4 Ramps
Bear
Bowl
Tunnel
2 Spinners
3 Penguins

3
For best performance, we recommend replacing the batteries that came with this toy
with three, new alkaline “AA” (LR6) batteries.
• Locate the battery compartment on the back of the bear.
• Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the
battery compartment door. Remove the exhausted batteries and throw them away.
• Insert three, new “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screws with a Phillips screwdriver.
• If this toy begins to operate erratically you may need to reset the electronics. Slide the power/
volume switch off and then back on.
• When sounds or lights from this toy become faint or stop, it’s time for an adult to change
the batteries.
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities (Europe only).
Battery Replacement
1.5V x 3
“AA" (LR6)

4
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury
or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-
zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from
the product. Dispose of batteries safely. Do not dispose of product in a fire. The batteries
inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.
Battery Safety Information
United States Only
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC Statement

5
Rolling Ramps & Silly Sounds
Power/Volume
Switch
• Slide the power/volume switch on the side of the bear to on with low volume , on with high
volume or off .
• Drop a ball into the bear’s hands. Listen to fun sounds and watch the bear’s nose light up as
the ball rolls down the ramp!

Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. N1891pr-0920
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA
Consumer Information
Care
• Wipe this toy with a clean cloth dampened with a mild soap and water solution.
• Do not immerse this toy.
• The bear has no consumer serviceable parts. Do not take the bear apart.
Storage
• All of the assembled parts can be disassembled for storage.

7
Assembly
• Note the numbers on the underside of each ramp.
• Insert and “snap” the ramp labeled 1 into the slot in the back of the bear.
• Connect the free end of ramp to the top of the tallest penguin.
Hint: The penguin will only connect to the ramp one way. Align the tab on the penguin with the
slot in the ramp.
1
Bear
Ramp 1
Tallest Penguin
2
• Insert and “snap” the ramp labeled 2 into the hole in the top of the tallest penguin.
• Connect the free end of ramp into the top of the mid-sized penguin.
Hint: The penguin will only connect to the ramp one way. Align the tab on the penguin with the
slot in the ramp.
Ramp 2
Mid-Sized Penguin

8
Assembly
• Insert and “snap” the ramp labeled 3 into the hole in the top of the mid-sized penguin.
• Connect the free end of the ramp into the top of the shortest penguin.
Hint: The penguin will only connect to the ramp one way. Align the tab on the penguin with the
slot in the ramp.
3
Ramp 3
Shortest Penguin
• Insert and “snap” the ramp labeled 4 into the hole in the top of the shortest penguin.
• Insert and “snap” the free end of the ramp into the slot on the bowl.
4
Ramp 4
Bowl

Assembly
• Align the tabs on the tunnel with the slots in the ramp above the mid-sized penguin.
Push down to “snap” in place.
6
Tunnel
• Fit the ends on the spinners into the slots on the sides of the ramp assembly, as shown.
5Spinners
9

10
Convertible Coaster
• Push the ramps together for sit and play fun!
• Pull the ramps apart for crawl and chase action!