Fisher-Price Robotz Rescue Heroes Hyper Jet HQ User manual

Figures sold separately and subject to availability.
w
w
w
.r
e
s
cu
e
h
e
r
o
e
s
.
c
o
m
Instructions: C5959
Please keep this instruction sheet for future reference, as it contains important information.
Requires three “C” (LR14) and three “AAA” (LR03) alkaline batteries (not included).
Adult assembly is required.
Tool required for battery installation:
Phillips screwdriver (not included).
TM

Parts
2
Not Shown: Label Sheet
Front Landing Gear (Smaller)
Tough Terrain Vehicle
Keytron™ Robot
2 Glider Supports
Water Cannon Launcher
Cargo Door
2 Water Missiles
Mission Central
Console
2 Rear Landing Gear (Larger)
Jet Body
Space Pod
Glider Wing
Stretcher
Ramp Hose
2 Wings

Building the Hyper Jet™
•Position the jet body with the bottom facing you.
•“Snap” the smaller front landing gear into the
jet body.
•“Snap” the two larger rear landing gear into the
jet body.
•Turn the jet body upright.
•“Snap” the hose into the hole in the cargo bay.
13
• “Snap” the two wings into the jet body, as shown.
•“Snap” the ramp into the cargo door, as shown.
2
4
3
Rear Landing
Gear (Larger)
Hose
Cargo Door
Ramp
Front Landing
Gear (Smaller)
Wing

Building the Hyper Jet™
•Position the cargo door near the back of the jet with
the ramp facing up.
•At an angle, fit the right side door peg into the right
hole in the jet body .
•Bend the door slightly and fit the left side door peg
into the left hole in the jet body .
•Rotate the cargo door up to close it. •Fit the pegs on the sides
of the Mission Central
Console into the two
grooves on the top of
the jet body, as shown.
•Rotate the Mission Central Console down to store it
in the jet cargo bay.
5 7
•“Snap” the two glider supports into the jet body,
as shown.
6
4
Cargo Door
Mission Central
Console
Glider Support
Peg
Groove
A
B
A
B

Building the Hyper Jet™
•Fit the glider wing onto the two pegs on the
glider supports.
•The glider wing is removable and will attach to the
back of most figures.
8
•Press and hold the latch on the jet body.
•Fit the space pod into the opening at the front of the
jet body and release the latch.
9
5
Glider Wing
Space Pod
P
R
E
S
S

Label Decoration
6
®
®
®
®
33
2
5
29
14
24
25
30
30
28
1
17
3
27
34
20
31
31
23
4
16
•Make sure the areas where the labels will be applied are clean and dry. Apply the labels as shown in the
illustration above.
•For best results, do not attempt to apply a label more than once.
21
6
26
26
15
15
32

Label Decoration
7
11
10 19
19
9
10
11
7
8
12
13
18
18
22

Battery Installation -
Mission Central Console
•Locate the battery compartment on the back of the
Mission Central Console.
•Loosen the screws in the battery compartment door
with a Phillips screwdriver. Remove the battery
compartment door.
•Insert three “C” (LR14) alkaline batteries as indicated
inside the battery compartment.
Hint: We recommend using alkaline batteries for
longer life.
•Replace the battery compartment door and tighten the
screws with a Phillips screwdriver. Do not over-tighten.
•When lights or sounds from the Mission Central
Console become faint or stop, it’s time for an adult to
change the batteries.
8
Battery
Compartment Door
1.5V x 3
“C” (LR14)
Shown Actual Size
Battery Installation - Keytron™Robot
•Locate the battery compartment on the bottom of
the robot.
•Loosen the screw in the battery compartment door
with a Phillips screwdriver. Open the battery compart-
ment door.
•Insert three “AAA” (LR03) alkaline batteries as
indicated on the outside of the door.
Hint: We recommend using alkaline batteries for
longer life.
•Close the battery compartment door and tighten the
screw with a Phillips screwdriver. Do not over-tighten.
•When sounds from the robot become faint or stop,
it’s time for an adult to change the batteries.
Battery
Compartment Door
1.5V x 3
“AAA” (LR03)
Shown Actual Size
Bottom View

9
Battery Safety Information
Batteries may leak fluids that can cause a chemical burn injury or ruin your toy.
To avoid battery leakage:
•Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or recharge-
able (nickel-cadmium).
•Insert batteries as indicated.
•Remove batteries during long periods of non-use. Always remove exhausted batteries from the toy. Dispose
of batteries safely. Do not dispose of batteries in a fire. The batteries may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type, as recommended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the toy before charging.
•If removable, rechargeable batteries are used, they are only to be charged under adult supervision.

Build the Hyperbot™!
•Press the latch on the jet body to detach the
space pod. •Open the canopy and slide a figure into the cockpit.
•Rotate the “arms” towards the front of the space pod.
•Close the canopy.
Space Pod
10
Figures sold separately and subject to availability.
2
1
•Fit the post on the bottom of the pod into the
rectangular opening on the Tough Terrain Vehicle.
•Rotate the “head” up over the canopy.
•Fit the water cannon into the hole in the “hand.”
•Place the stretcher on the back of the Tough
Terrain Vehicle.
3
•Hyperbot™ is now ready for action!
4Hyperbot™