Fisher-Price Ramps Around Garage B1832 User manual

B1832
Instructions
w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Ramps Around Garage™
Please keep this instruction sheet for future reference, as it contains important information.
Requires three "AA" (LR6) alkaline batteries (not included).
Adult assembly is required.
Tool required for assembly and battery installation: Phillips screwdriver (not included).

2
Parts
CAUTION
This product contains small parts in its unassembled state.
Adult assembly is required.
Parts Not Shown:
Label Sheet
Car
To w Tr u c k
2 Figures
#6 x 1" Screw - 4
Shown Actual Size
#6 x 1/2" Screw - 6
Shown Actual Size
Elevator Elevator Handle
Elevator Roof
Upper Track
Lower Track
Track Support
Garage Base
Diagnostic Center
Post
Gate
Ramp
Vacuum
News Stand
2 Fences
Note: Tighten and loosen all
screws with a Phillips screwdriver.
Do not over-tighten the screws.

3
Assembly
• Position the elevator on a flat surface. Note the locations
of the bottom slots and the upper tabs on the elevator.
• Hold the base at an angle. While making sure the upper
tabs on the elevator fit into the grooves in the base ,
insert the tabs on the base into the bottom slots on the
elevator .
• Press down on the base to "snap" the elevator in place.
1
2
• Fit the elevator roof on the elevator.
• Insert four #6 x 1" screws into the elevator roof and tighten.
Elevator Roof
Bottom Slots
Elevator Upper Tabs
Base Grooves
Tabs


•Place the garage on its side on a flat surface, as shown.
• Fit the connectors on the end of the ramp into the holes
on the top of the base. Be sure to fit the hooked tab on
the side of the elevator into the slot on the ramp. Press
the ramp until it "snaps" in place.
•Place the garage upright again.
Hooked Tab
Slot
• Slide and "snap" the
diagnostic center into
the base.
• Turn the base over and insert two 1/2"screws into the
base. Tighten the screws.
• Turn the base upright.
Diagnostic Center
3
4
Bottom View
Ramp

4
• "Snap" the tabs on the lower track into the slots in
the base.
Lower Track
Assembly
•Press the clamp on the track support onto the
base column.
•Rotate the track support so that the holes in the
support fit over the pegs on the lower track.
Track Support
Clamp
Column
5
6
Pegs Through Holes
•Place the garage on its side on a flat surface, as shown.
•"Snap" the rectangular connectors on the upper track into
the holes at the top of the base.
• Fit the other end of the upper track over the end of the
lower track.
•Place the garage upright again.
• Insert two
1/2"screws into the holes on the underside of
the upper track, as shown. Tighten the screws.
Upper Track
7
•Tip the elevator handle and fit the hooked tab through the
channel in the side of the elevator .
• Slide the elevator handle down and "snap" the tab on the
handle into the slot in the elevator .
Hooked Tab
Channel
Slot
8
Elevator
Handle



5
•"Snap" the news stand into the top side of the base.
News Stand
9
Assembly
• To attach the post,
turn the base over
so the bottom is facing you.
• Align the holes in the post with the pegs, as shown.
• Insert two
1/2"screws into the post and tighten.
• Turn the base upright.
Post
Pegs
Vacuum
Bottom View
• "Snap" the gate into the slots on the top side of the base.
Gate
11
• "Snap" the vacuum into the base.
12
10

6
Battery Installation
• Locate the battery compartment on the top level of
the garage.
• Loosen the screw in the battery compartment door.
Remove the battery compartment door.
• Insert three "AA" (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for
longer life.
• Replace the battery compartment door and tighten
the screw.
Battery
Compartment
Door
1.5V x 3
“AA” (LR6)
SHOWN ACTUAL SIZE
Battery Safety Information
Batteries may leak fluids that can cause a chemical
burn injury or ruin your toy. To avoid battery leakage:
•Do not mix old and new batteries or batteries of
different types: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
•Insert batteries as indicated on the battery
compartment door.
•Remove batteries during long periods of non-use.
Always remove exhausted batteries from the toy.
Dispose of batteries safely. Do not dispose of
batteries in a fire.The batteries may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type,
as recommended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the toy
before charging.
•If removable, rechargeable batteries are used, they
are only to be charged under adult supervision.

Decoration
•Before applying labels, wipe the surface of the toy with a clean, dry cloth to remove
dust or oils.
•For best results, avoid repositioning a label once it has been applied.
•Apply labels as shown in the illustration.
4
6
910
1
7
2
3
Fun sounds all around the garage!
Press these buttons
around the garage
to hear many fun
sound effects.
Telephone
Gas Pump
Diagnostic Center
Track Entrance
•Locate the On/Off switch under
the battery compartment.
•Slide the switch to the •position
to turn the toy on and to the
o position to turn it off.
Hint: If your child is not actively
playing with this toy, it turns off
automatically (sleep mode).
•When your child is finished
playing with this toy, slide
the on/off switch to the
off position o .
On/Off Switch
o
•
7
5
8

FCC Note (United States Only)
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio o television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment
and receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by
the manufacturer responsible for compliance could void the
user's authority to operate the equipment.
Consumer Information
Questions? We’d like to hear from you!
Call Fisher-Price®Consumer Relations, toll-free at
1-800-432-5437, 8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or, write to:
Fisher-Price®Consumer Relations
636 Girard Avenue
East Aurora, New York 14052, U.S.A.
Care
•Wipe the toy with a clean cloth dampened with a mild
soap and water solution.
•Do not immerse the toy.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2003 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in Mexico B1832a-0920
For countries outside the United States:
CANADA
Questions? 1-800-567-7724, Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
GREAT BRITAIN
Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500302.
AUSTRALIA
Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
NEW ZEALAND
16-18 William Pickering Drive, Albany 1331, Auckland.
ASIA
Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.