Fisher-Price TOUGH TRIKE 72643 User manual

•Adult supervision is required.
•Never use near steps, sloped driveways, hills, roadways,
alleys, swimming pool areas or other bodies of water.
•Always wear shoes or sneakers.
•Never allow more than one rider.
•Observe child weight limit: maximum 55 lbs.
Please keep these instructions for future reference.
Adult assembly is required.
Tools needed for assembly: Hammer, Phillips Screwdriver, Scrap Block of Wood.
If you have any questions about this product, or are missing a part, please call
Fisher-Price®toll-free at 1-800-432-KIDS, rather than return this product to the store.
Age: 2-5 years.
Weight Limit: 55 lbs.
WARNING
Tough Trike
Instructions
Model Numbers: 72643, 72644
Please keep small parts, hardware and plastic bags
out of children’s reach. Dispose of plastic bags properly.
CAUTION
Model Number: 72643 Model Number: 72644

•Please save all packaging material until assembly is complete to ensure that no parts are discarded.
•Wipe each part with a clean dry cloth before assembly.
•If you are missing a part, please call Fisher-Price®toll-free at 1-800-432-KIDS rather than return this product to the store.
(ALL SHOWN ACTUAL SIZE)
#8 x 5/8" Screw - 6
#8 x 11/4" Screw - 6
Lock Washer - 2
2
Parts
3
4
6
8
9
11
17
Illustration
Number Part Description Quantity
1Frame 1
2Rear Wheel 2
3Rear Wheel Cover 2
4Rear Axle 1
5Seat 1
6Booster Seat 1
7 Tank 1
8Key Console 1
9Handlebar 1
10 Frame Cover 1
11 Fork 1
12 Fender 1
Illustration
Number Part Description Quantity
13 Front Wheel 1
14 Front Wheel Cover 2
15 Pedal Hub 2
16 Front Axle 1
17 Front Axle Cover 2
18 Pedal 2
19 Lock Washer 2
20 Cap Nut 2
21 #8 x 11/4" Screw 6
22 #8 x 5/8" Screw 6
23 Cap Nut Assembly Tool 3
Label Sheet (not shown) 1
1
7
2
12
14
10
15
16
13
5
22
22
21
18
19
20
22
21
21
Cap Nut - 2
23

IMPORTANT! Remove the cap nut assembly tools from the
rear axle and save them. The cap nut assembly tools will be
used for assembly steps - and then discarded when
the rear wheel assembly is complete.
Axle Holes
Rear Axle
Cap Nut
Cap Nut Assembly Tool
Recessed Side
Cap Nut
Assembly Tool
•Place the other rear wheel onto the rear axle with the
recessed side facing up.
•Place a cap nut into a cap nut assembly tool.
•Place the cap nut with cap nut assembly tool onto the end of
the rear axle and tap with a hammer until secure.
•Remove both cap nut assembly tools and dispose of them
properly.
•Place a rear wheel onto the rear axle with the recessed side
facing down toward the cap nut assembly tool.
•Turn the frame on its side.
•Insert the rear axle through the four axle holes in the rear
of the frame.
3
Assembly
Frame
•Place a scrap block of wood on a flat surface.
•Fit a cap nut into a cap nut assembly tool.
•Insert one end of the rear axle into a cap nut.
•Tap the end of the rear axle with a hammer. Make sure the
cap nut is securely attached to the rear axle.
Scrap Block of Wood
Rear Wheel
Cap Nut
Assembly Tool

•Insert a lock washer into the pedal slot. Make sure the
raised tabs on the lock washer are facing the closed, or
outside end of the pedal.
•Repeat this procedure to fit the other lock washer into the
other pedal.
Outside End of Pedal
Pedal Slot
Raised Tabs
•Snap a rear wheel cover into the recessed area in each
rear wheel.
•Fit the slots in the pedal hubs onto the metal tabs on the
front axle.
•Snap the pedal hubs together securely.
•Slide the front wheel cover onto one end of the front axle so
that the pedal hub fits into the square recessed area inside
the front wheel cover.
•Insert the front axle assembly into the front wheel. Make
sure the two posts on the front wheel cover fit into the
corners of the square opening in the front wheel.
•Slide the other front wheel cover onto the front axle
assembly. Align the posts on the front wheel cover with the
holes in the front axle assembly.
•Insert two 11/4"screws into each front wheel cover. Tighten
the screws with a Phillips screwdriver. Do not over-tighten.
Metal Tab
4
Assembly
Rear Wheel Cover
Front Axle
Pedal Hubs
Post
Front Axle
Front Wheel Cover
Front Axle
Assembly
Front
Wheel
Post
Front Wheel Cover
Lock Washer
Pedal Hub
Front Wheel
Cover

•Place a scrap block of wood under the front wheel assembly.
•Fit a pedal onto one end of the front axle.
•With the lock washer centered over the front axle end, tap
the pedal until it is secure.
•Repeat this procedure to attach the other pedal to the other
end of the front axle.
•Position the fender between the fork arms, so that the
pointed end of the fender is facing up and the grooves on
the fork are facing down.
•Insert one 5/8" screw through the fender and into the fork.
Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
•Place the front wheel assembly between the fork arms so
the front axle rests in the groove on each fork arm.
•Fit a front axle cover on the front axle on one fork arm.
•Insert two 5/8" screws through the front axle cover and into
the fork. Tighten the screws with a Phillips screwdriver. Do
not over-tighten.
•Repeat this procedure to attach the front axle cover to the
other side of the front wheel assembly.
Groove
Front Axle Cover
Groove
Pointed
End
5
Pedal
Assembly
Front Axle
Fender
Fork
Fork Arm
Front Axle
Front Wheel
Assembly

•Snap the frame cover (wider side facing forward) on the
underside of the frame.
•Insert the fork post through the frame hole making sure the
pointed end of the fender faces forward.
•Fit the handlebar onto the fork post.
•Place the key console on the center of the handlebar, so
that the key faces the rear.
•Align the key console holes with the handlebar holes and
insert two 11/4" screws through the front and back of the key
console. Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Pointed End
Wider Side
Faces Forward
6
Assembly
Frame Cover
Frame
Fork Post
Frame
Fork Post
Handlebar
Key Console
Handlebar

•Place the tank on the frame, as shown.
•Align the hole in the tank with the hole in the frame.
•Insert one 5/8" screw through the tank and into the frame.
Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
•Insert the back tab on the booster seat first and then press
down on the front to secure the two front tabs.
•As your child grows, the booster seat may be removed. To
remove, insert a flat end screwdriver into the front slots and
push up.
•Insert the left rear peg on the seat into the left opening on
the frame.
•Position the right rear peg on the seat above the right
opening and snap firmly into place.
Helpful Hint:Check your child's fit on the Tough Trike by
observing the seat to pedal distance as it is being ridden.
If the pedals seem too far away for your child, attach the
booster seat.
Front Slots
Peg
Back Tab
7
Assembly
Tank
Frame
Seat
Frame
Attach
Remove
Front Tabs

Fisher-Price, Inc., 636 Girard Avenue, East Aurora,
New York 14052, warrants to the original owner that the
Tough Trike is free from all defects in material and workman-
ship when used under normal conditions for a period of three
(3) years from the date of purchase.
Should the product fail to perform properly, we will repair or
replace it at our option, free of charge. Purchaser is responsi-
ble for shipping the product to Fisher-Price Consumer Affairs
at the address indicated above and for all associated freight
and insurance cost.
Fisher-Price, Inc. will bear the cost of shipping the repaired or
replaced item to you. This warranty is void if the owner
repairs or modifies the product. This warranty excludes any
liability other than that expressly stated above including but
not limited to any incidental or consequential damages.
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY
VARY FROM STATE TO STATE.
•Check the plastic parts regularly and if broken or cracked,
dispose of them properly.
•Check all fasteners regularly to be sure they are tight. If the
fasteners are not tight, tighten them as necessary.
•To clean the Tough Trike, use a mild soap and water
solution and clean cloth. Rinse clean with water to remove
soap residue.
©1997 Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052 Printed in U.S.A. 72643, 72644 1 72643-0920
8
•Proper label application will help to keep the labels looking
their best!
•Wash your hands before applying the labels.
•Make sure areas where the labels will be applied are clean
and dry. Wipe the Tough Trike with a clean, soft, dry cloth to
remove any dust or oils.
•Apply the labels as shown in the illustration above.
•For best results, avoid applying a label more than once.
•After applying a label, rub the label firmly with a cloth to
make sure the label is adhered to the Tough Trike.
Assembly Maintenance
Three (3) Year
Limited Warranty
22
A
9
3
Assembly is now complete.
22
B
If you have any questions about this product:
In Canada, call 1-800-567-7724, or write to: Mattel Canada Inc.,
6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
In Great Britain, telephone [phone].
In Australia, call the Fisher-Price Australian Consumer Advisory Service
toll-free at 1-800-800-812, or write to: Fisher-Price, Mattel Pty. Limited,
461 Plummer Street, Port Melbourne, Victoria 3207.
Questions? We'd like to hear from you!
Call Fisher-Price®Consumer Affairs, toll-free at
1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470. Or, write to: Fisher-Price®
Consumer Affairs, 636 Girard Avenue, East Aurora,
New York 14052.
Model Number 72643
Model Number 72644
7
4
3
10
8
8
6
1
9
4
7
2
45
2
56 1