Fisher-Price W6117 User manual

7
www.fisher-price.com
W6117
Vehicles shown in photographs and illustrations may be different
than the vehicles included with your toy.
Please keep this instruction sheet for future reference,
as it contains important information.
Requires seven “AAA” batteries (one battery included) for operation.
Adult assembly is required.
Tool required for battery installation: Phillips screwdriver (not included).

2
Assembled Parts
Dumpster 2 Flags
2 Buildings
2 Supports
Bridge Track
Long Ramp Track
4 Curved Tracks GuardrailStraight Track
C Track
Easy Rail TrackPlatformGarage
Track Base
Race Banner
Minion Base
Short Ramp Track

3
Assembly
• Fit the tabs on the dumpster into the slots in
the minion base. Push to "snap" in place.
• Fit the the easy rail track onto the track base,
as shown.
• Then, fit the tabs on the garage into the slots
in the track base. Push to "snap" in place.
• Fit both supports onto the C track.
Hint: The supports are designed to fit one way.
If a support not seem to fit, try the other support!
• Turn the C track upright.
• Fit the village buildings onto the posts on the
track, as shown.
• Fit the pegs on the flags and race banner
into the sockets on the C track.
1
4
5
2
3
Dumpster
Minion Base
Garage
Track Base
Easy Rail
Track
C Track
Supports
Race Banner
Flags

4
Assembly
• Snap the bridge track onto the end of the
C track, as shown.
• Snap the platform onto the track assembly.
• Fit the guardrail onto a curved track,
as shown.
• Track pieces easily snap together.
6
7
9
8
Bridge Track
Platform

5
Bridge Track
Long Ramp Track
Curved Track
2 Curved Tracks
Curved Track
with Guardrail
Straight Track
Easy Rail Track
Minion Base
Short Ramp Track
Track Layout
C Track

6
Consumer Information
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment. This device complies with
Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Care
• Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not
immerse this toy.
• This toy has no consumer serviceable parts. Do not take this toy apart.
PRINTED IN CHINA W6117pr-0920
CO
N
S
UMER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2011 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc., unless otherwise indicated.
© Disney/Pixar; Pacer™; Gremlin™
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities.

7
Let's Go!
Hint: We do not recommend using Finn
McMissle on carpets. For best performance,
use on hard, flat surfaces.
• Point the remote controller toward the
vehicle and push the stick forward. The
vehicle moves forward.
• Pull the stick all the way back and the
vehicle travels in reverse. Release the stick
to stop.
• Turn the cameras to knock the vehicle off the
track as it drives by!
1
2
3
FORWARD
STOP
REVERSE
2
3
S
T
OP
REV
E
2
3
1
• Press the power button on top of the vehicle.
The ready light turns on.
POWER BUTTON
READY LIGHT
1
2
3
4
• Push down on Holly Shiftwell to hear fun
phrases and sounds!

8
Battery Installation
Remote Controller
• Locate the battery compartment on the back
of the remote controller.
• Loosen the screw in the battery compartment
door with a Phillips screwdriver. Remove the
battery compartment door and insert three
“AAA” (LR03) alkaline batteries.
• Replace the battery compartment door and
tighten the screw with a Phillips screwdriver.
Do not over-tighten.
• If the remote controller begins to operate
erratically, you may need to reset the electronics.
Remove the batteries and reinstall.
We recommend the use of alkaline batteries for longer battery life.
IMPORTANT! Under normal use conditions, the batteries in the vehicle will require
replacement more often than the batteries in the remote controller. For additional
information, refer to the troubleshooting section.
RC Vehicle
• Loosen the screws in the bottom of the vehicle
with a Phillips screwdriver. Lift the top of the vehicle
off of the chassis to access the battery compartment.
Insert three “AAA” (LR03) alkaline batteries.
• Replace the top of the vehicle and tighten the screw
with a Phillips screwdriver. Do not over-tighten.
• If the vehicle begins to operate erratically,
you may need to reset the electronics.
Remove the batteries and reinstall.
Talking Vehicle
• Loosen the screws in the bottom of the vehicle.
•
Remove the exhausted battery and dispose of it properly.
• Insert a new "AAA" (LR03) alkaline battery.
•
Replace the bottom of the vehicle and tighten the screws.
Do not over-tighten.
• If this toy begins to operate erratically, you may
need to reset the electronics. Remove the
battery and reinstall.
• When sounds from this toy become faint or stop,
it’s time for an adult to change the battery.

9
1,5V x 7
“AAA” (LR03)
Battery Safety Information
ICES-003
NMB-003
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your toy. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from
the toy. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries
inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.
• This Class B digital apparatus complies with Canadian ICES-003.
• Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference that
may cause undesired operation.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas
produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement
du dispositif.

10
Troubleshooting
PROBLEM SOLUTION
Finn McMissile
drives slowly
Battery power in the vehicle may be weak. Replace all three
batteries in the vehicle with new, alkaline batteries.
The wheels on the vehicle may be dirty. Wipe them with
a clean cloth.
Finn McMissle does
not respond to the
remote controller
Battery power in the remote controller may be weak. Replace all
three batteries in the remote controller with new, alkaline batteries.
You may be beyond the maximum range of the remote controller
which is about 12 feet (3,7 m).
You may not have a clear path between the remote controller
and the vehicle. This toy works best when there are no
obstructions between the vehicle and the remote controller.
Bright sunlight or fluorescent lights may affect the range of the
remote controller. Try dimming the room you are playing in.
The vehicle may have shut off. If you do not operate the remote
controller for a few minutes, the vehicle shuts off automatically
and the ready light turns off. Press the power button on the
vehicle, and operate the remote controller to restart.
Sounds from Holly
Shiftwell become faint
or stop
Battery power in the vehicle may be weak. Replace battery in the
vehicle with a new, alkaline battery.