FLIR F-Series User manual

427-0033-00-12 Version 110 February 2019
This document does not contain any export-controlled information.
Installation
Manual
F-Series ID

427-0033-00-12 Version 110
This document does not contain any export-controlled information.
© 2019 FLIR Systems, Inc. All rights reserved worldwide. No parts of this manual, in whole or in part, may be
copied, photocopied, translated, or transmitted to any electronic medium or machine readable form without the
prior written permission of FLIR Systems, Inc.
Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR
Systems, Inc. and/or its subsidiaries. All other trademarks, trade names, or company names referenced herein are
used for identification only and are the property of their respective owners.
This product is protected by patents, design patents, patents pending, or design patents pending.
Photographs and images appearing in this manual may have been modified for illustrative purposes using
commercial image editing software and may not always reflect an actual product configuration.
The contents of this document are subject to change without notice.
For additional information visit www.flir.com or write to FLIR Systems, Inc.
FLIR Systems, Inc.
6769 Hollister Avenue
Goleta, CA 93117
Support: https://www.flir.com/support-center/support-hq/
Important Instructions and Notices to the User:
Modification of this device without the express authorization of FLIR Systems, Inc., may void the user’s authority
under the FCC Rules to operate this device.
Note 1: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense. Shielded cables
must be used to connect this device to other devices.
Note 2: If ferrites are supplied with this equipment, the equipment was tested for compliance with the FCC limits for
a Class A digital device using power cables with the ferrites installed. When connecting one or two power cables to
the equipment, the supplied ferrites must be used with this equipment.
Industry Canada Notice:
This Class A digital apparatus complies with Canadian ICES-003.
Avis d’Industrie Canada:
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Proper Disposal of Electrical and Electronic Equipment (EEE)
The European Union (EU) has enacted Waste Electrical and Electronic Equipment
Directive 2002/96/EC (WEEE), which aims to prevent EEE waste from arising; to encourage
reuse, recycling, and recovery of EEE waste; and to promote environmental responsibility.
In accordance with these regulations, all EEE products labeled with the crossed out
wheeled bin either on the product itself or in the product literature must not be disposed of in
regular rubbish bins, mixed with regular household or other commercial waste, or by other
regular municipal waste collection means. Instead, and in order to prevent possible harm to
the environment or human health, all EEE products (including any cables that came with the
product) should be responsibly discarded or recycled.
To identify a responsible disposal method nearby, please contact a local waste collection or recycling service, the
original place of purchase or product supplier, or the responsible government authority in the area. Business users
should contact their supplier or refer to their purchase contract.
Document History
Version Date Comment
100 December 2018 V1.3.0
110 February 2019 Updated video encoding defaults and firmware update information; added 802.1x
support, TLS configuration, and Nexus CGI interface

Table of Contents
427-0033-00-12 Version 110 February 2019 3
This document does not contain any export-controlled information.
Table of Contents
F-Series ID Camera Installation
1.1 Camera Overview ...................................................................................................... 5
1.2 Warnings and Cautions .............................................................................................. 5
1.3 Installation Overview .................................................................................................. 6
1.3.1 Camera Connection Options ............................................................................. 6
1.3.2 Camera Mounting Accessories ......................................................................... 7
1.3.3 Supplied Components ....................................................................................... 7
1.3.4 Additional Supplies ........................................................................................... 7
1.3.5 Camera Placement ........................................................................................... 8
1.3.6 Bench Testing ................................................................................................... 8
1.3.7 Prior to Cutting/Drilling Holes ............................................................................ 8
1.3.8 Camera Mounting ............................................................................................. 8
1.3.9 Removing the Back Cover ................................................................................ 9
1.3.10 Cable Gland Sealing ....................................................................................... 9
1.3.11 Cable Glands and Spare Parts Kit ................................................................ 10
1.3.12 Cable Gland Seal Inserts .............................................................................. 10
1.4 Camera Connections ............................................................................................... 11
1.4.1 Connecting power ........................................................................................... 11
1.4.2 Video Connection ............................................................................................ 12
1.4.3 GPIO Alarm Connections ................................................................................ 12
1.4.4 Ethernet Connection ....................................................................................... 12
1.5 F-Series ID Camera Specifications .......................................................................... 13
Basic Operation and Configuration
2.1 IP Camera, ONVIF Profile S Compliant ................................................................... 15
2.1.1 Server Configuration ....................................................................................... 15
2.2 Camera Bench Test ................................................................................................. 15
2.2.1 Set IP Address using the FLIR Discovery Network Assistant (DNA) .............. 15
2.2.2 Log into the Camera Web Page ...................................................................... 16
2.2.3 Live Video Page .............................................................................................. 17
2.3 Basic Camera Configuration .................................................................................... 20
2.3.1 Expert and Admin Accounts ............................................................................ 20
2.3.2 Setup Menu ..................................................................................................... 20
2.3.3 Maintenance Menu > Server Page ................................................................. 21
2.4 Thermal Imaging Overview ...................................................................................... 29
2.5 Troubleshooting Tips ............................................................................................... 30

Table of Contents
427-0033-00-12 Version 110 February 2019 4
This document does not contain any export-controlled information.
Advanced Configuration
3.1 Setup Menu ..............................................................................................................33
3.1.1 Temperature Page ...........................................................................................33
3.1.2 Input/Output (IO) Page ....................................................................................34
3.1.3 Video Setup .....................................................................................................34
3.1.4 Thermal Image Setup - IR Page ......................................................................36
3.1.5 Video Analytics Setup ......................................................................................38
3.2 Maintenance Menu ...................................................................................................43
3.2.1 Sensor Menu ...................................................................................................44
3.2.2 Files Menu .......................................................................................................57
3.2.3 Product Info Menu ...........................................................................................60

1
427-0033-00-12 Version 110 February 2019 5
This document does not contain any export-controlled information.
F-Series ID Camera Installation
This manual describes the installation and initial configuration of the F-Series ID thermal camera. The
F-Series ID camera has software providing for on-board video analytics: setting of detection regions,
trip lines, and classification of detected objects. Refer to Video Analytics Setup, pg. 38.
1.1 Camera Overview
The F-Series ID cameras are components within the FLIR Thermal Fence. The video from the camera
can be viewed over a traditional analog video network or it can be viewed by streaming it over an IP
network using M-JPEG and H.264 encoding. The Ethernet connection also provides for camera
configuration and control using either a web browser or a video management system (VMS) such as
FLIR LatitudeTM.
The FLIR Thermal Fence combines FLIR thermal security cameras and the FLIR Latitude control and
management software in a fully integrated perimeter security solution. The FLIR Thermal Fence
provides automated perimeter surveillance, intrusion detection, and alert capabilities for perimeter
security applications including critical infrastructure, petrochemical facilities, nuclear facilities,
commercial campuses, and residential neighborhoods. The FLIR Thermal Fence gives you instant,
automated threat detection and visual threat assessment capability around the clock in one easy-to-
use package.
If help is needed during the installation process, contact the local FLIR service representative or
contact support at: https://www.flir.com/support-center/support-hq/. All installers and integrators are
encouraged to take advantage of the training offered by FLIR; visit
https://www.flir.com/support-center/training/ for more information.
1.2 Warnings and Cautions
For safety, and to achieve the highest levels of performance from the F-Series ID camera system,
always follow the warnings and cautions in this manual when handling and operating the camera.
Warning!
Caution!
If mounting the F-Series ID camera on a pole, tower or any elevated location, use industry standard
safe practices to avoid injuries.
Except as described in this manual, do not open the F-Series ID camera for any reason.
Disassembly of the camera can cause permanent damage and will void the warranty.
Be careful not to leave fingerprints on the F-Series ID camera’s infrared optics.
The F-Series ID camera requires a power supply of 24 V. Operating the camera outside the specified
input voltage range or the specified operating temperature range can cause permanent damage.

427-0033-00-12 Version 110 February 2019 6
This document does not contain any export-controlled information.
F-Series ID Camera Installation
1.3 Installation Overview
The F-Series ID Camera is an infrared thermal imaging camera intended for outdoor applications,
and can be installed in a fixed location or on a pan/tilt mechanism.
The F-Series ID camera is intended to be mounted on a medium-duty fixed pedestal mount or wall
mount commonly used in the CCTV industry. Cables exit from the back of the camera housing. The
mount must support up to 30 lbs. (15 KG).
1.3.1 Camera Connection Options
Camera connections are made through water-tight cable gland seals on the rear of the camera.
Refer to Cable Gland Sealing, pg. 9 to ensure the glands are used correctly and the connections are
properly sealed.
The camera is powered with a conventional power supply using 21 - 30 Vac or 21 - 30 Vdc.
The F-Series ID camera produces both analog video and digital (IP) video output. Analog video will
require a connection to a video monitor or an analog video matrix switch.
An Ethernet connection is required for IP video streaming and for command and control
communications.
Several third-party video management systems are supported by FLIR IP cameras. Because these
systems tend to evolve and change over time, contact the local FLIR representative or FLIR
Technical Support for information.
General Purpose Input/Output (GPIO)
The camera can receive a single input signal and can provide a single output signal. Refer to GPIO
Alarm Connections, pg. 12.
Input Signal—When an external alarm device closes a switch to complete the circuit for the
camera, an input alarm is generated by the GPIO for the Alarm Manager.
Output Signal—When an output alarm is generated by the Alarm Manager for the GPIO, the
camera closes its internal switch to complete the circuit for the receiving device.
Figure 1-1: F-Series ID Camera
Shipping plugs only -
Remove before installing

427-0033-00-12 Version 110 February 2019 7
This document does not contain any export-controlled information.
F-Series ID Camera Installation
1.3.2 Camera Mounting Accessories
The following accessories are available for purchase from FLIR Systems, Inc.
• Wall Mount Kit (500-0462-00) – The wall mount is designed to safely support loads up to 40
pounds (18 kg). The mount features a fully adjustable swivel head allowing 360 degree
horizontal and 75 degree vertical adjustment. The mount is constructed of aluminum with a gray
polyester powder coat finish.
• Pole Mount Adapter (4119507) – The pole mount adapter is designed for use with the wall
mount kit (500-0462-00) when installation is required on a pole. The adapter attaches on poles
having 1.5-inch (3.81 cm) to 8-inch (20.32 cm) diameters. The mount is constructed of aluminum
with a gray polyester powder coat finish and stainless steel straps.
• Pedestal Mount Kit (500-0463-00) – The pedestal mount is designed to support loads up to 40
pounds (18 kg). The mount features a fully adjustable swivel head allowing 360 degree
horizontal and 75 degree vertical adjustment. The mount is constructed of aluminum and has a
gray polyester powder coat finish.
1.3.3 Supplied Components
The F-Series ID camera includes these standard components:
• Fixed Camera Unit
• Cable Glands and Spare Parts kit
1.3.4 Additional Supplies
The installer will need to supply the following items, which are specific to the installation.
Refer to Camera Connections, pg. 11.
• 24 V Power supply
• Electrical wire: system power, 3-conductor, shielded, gauge determined by cable length;
GPIO alarm cable (optional), 5-conductor, 20 AWG maximum
• Camera grounding strap
• Coaxial RG59U video cables (BNC connector at the camera end) for analog video (optional)
• Shielded Category 6 Ethernet cable for control, streaming video, and for software updates.
• Hardware/software for viewing the video (streaming IP video or analog video)
• Miscellaneous electrical hardware, camera mount, connectors, and tools

427-0033-00-12 Version 110 February 2019 8
This document does not contain any export-controlled information.
F-Series ID Camera Installation
1.3.5 Camera Placement
The F-Series ID camera should be mounted upright on top of the mounting surface. Adhere to all
local and industry standards, codes, and best practices.
For installations with multiple cameras with on-board video analytics, the fields of view of cameras
should overlap in order to remove all dead zones in which a camera cannot see a target “head to
toe”. The camera’s on-board analytics must be calibrated to detect targets. Refer to Video Analytics
Setup, pg. 38.
• Install the camera at a height of approximately 4 m (13 ft) or more.
• Typically direct the camera towards the ground with the maximum possible tilt angle (α) to
ensure that the field of view includes as little of the skyline as possible.
• Ensure that cameras are mounted on stable mounts with minimal vibrations and maximal
resistance to wind.
• The tilt angle (α) is the angle between vertical and the center of the camera field of view.
1.3.6 Bench Testing
Connect the power, analog video, and Ethernet connections and confirm that the video is shown on
a monitor when the power is turned on. The IP address of the camera web server is shown on the
analog video for approximately 90 seconds after power is applied. For configuration and basic setup
information using the onboard web server, refer to Camera Bench Test, pg. 15.
1.3.7 Prior to Cutting/Drilling Holes
When selecting a mounting location for the F-Series ID camera, consider cable lengths and cable
routing. Ensure the cables are long enough, given the proposed mounting locations and cable
routing requirements, and route the cables before you install the components.
Use cables that have sufficient dimensions to ensure safety (for power cables) and adequate signal
strength (for video and communications).
1.3.8 Camera Mounting
F-Series ID cameras must be mounted upright on top of the mounting surface, with the base below
the camera. The unit should not be hung upside down.
Verify both sides of the mounting surface are accessible.
α

427-0033-00-12 Version 110 February 2019 9
This document does not contain any export-controlled information.
F-Series ID Camera Installation
Use a thread locking compound such as Loctite 242 or equivalent with all metal to metal threaded
connections.
Once the holes are drilled in the mounting surface, install three (3) to five (5) 1/4-20 threaded
fasteners into the base of the camera with thread-locking compound.
Secure the camera to the mount with three (3) to five (5) 1/4-20 threaded fasteners as shown below.
1.3.9 Removing the Back Cover
Use a 3 mm hex key to loosen the four captive screws,
exposing the connections at the back of the camera
enclosure. There is a grounding wire connected
between the case and the back cover as shown. If the
grounding wire is temporarily disconnected during the
installation, it must be reconnected to ensure proper
grounding of the camera.
1.3.10 Cable Gland Sealing
Proper installation of cable sealing glands and use of
appropriate elastomer inserts is critical to long term
reliability. Cables enter the camera mount enclosure
through liquid-tight compression glands. Leave the
gland nuts loosened until all cable installation has been
completed. Inspect and install gland fittings in the back cover with leak sealant and tighten to ensure
water tight fittings. Teflon tape or pipe sealant (i.e. DuPont RectorSeal T™) are suitable sealants.
Figure 1-2: F-Series ID Camera Mounting Holes
5.0
(NOMINAL
BASE SURFACE
DIAMETER)
F.O.V.
DIRECTION
±.0201.00
1.00±.020
1.00±.020
1.00±.020
5X 1/4 - 20 THREAD, 0.75 DEEP
Not to scale
All dimension are in inches

427-0033-00-12 Version 110 February 2019 10
This document does not contain any export-controlled information.
F-Series ID Camera Installation
1.3.11 Cable Glands and Spare Parts Kit
The kit contains the two 3/4” cable glands and gland
seal plugs required for non-conduit installations.
The remaining parts included in the kit are:
• a spare ground wire
• a spare ground nut and lock washer
• two spare power terminal block plugs
• two spare terminal block plugs
• four spare F-Series back cover screws
1.3.12 Cable Gland Seal Inserts
The camera comes with two 3/4” NPT cable
glands, each with a three hole gland seal
insert. Cables may be between 0.23" to 0.29"
OD. Up to five cables may be needed. Plugs
are required for any insert hole(s) not used.
If non-standard cable diameters are used, you
may need to locate or fabricate the
appropriate insert to fit the desired cable. FLIR
Systems, Inc. does not provide cable gland
inserts other than the inserts supplied with the
system.
Note
Insert the cables through the gland seal before terminating and connecting them. The terminated
connectors will generally not fit through the cable gland. If a terminated cable is required, make a
clean, singular cut in the gland seal to install the cable into the gland seal.
Camera Power
GPIO Alarm Ethernet
Heater Power
Seal plugs
Ground
Lug

427-0033-00-12 Version 110 February 2019 11
This document does not contain any export-controlled information.
F-Series ID Camera Installation
1.4 Camera Connections
1.4.1 Connecting power
The camera itself does not have an on/off switch. Generally the F-Series ID camera will be
connected to a circuit breaker and the circuit breaker will be used to apply or remove power to the
Back Cover
Chassis
GND
16 AWG
Shielded
16 AWG
Shielded
24 VAC/DC+
24 VAC/DC-
Earth Ground
24 VAC/DC+
24 VAC/DC-
Earth Ground
Local
Ground
24
VAC/DC
24
VAC/DC
Male
BNC Ethernet
Analog Video
1
2
3
1
2
3
Ethernet
Camera
Power
Heater
Power
Left
Cable
Gland
3/4” NPT for Cable
Gland or Conduit
Right
Cable
Gland
Alarm Out
GND
Alarm In +
GPIO Alarm
5
4
3
2
1
20 AWG MAX
GPIO Alarm
-
Figure 1-3: Camera Connections
IP Network
Figure 1-4: Connector locations
Analog Video
(monitoring output only)
Not used Camera Power
Heater Power
Analog Video
GPIO
Alarms

427-0033-00-12 Version 110 February 2019 12
This document does not contain any export-controlled information.
F-Series ID Camera Installation
camera. If power is supplied to it, the camera will be in one of two modes: Booting Up or Powered
On.
The power cable supplied by the installer must use wires that are sufficient size gauge (16 AWG
recommended) for the supply voltage and length of the cable run, to ensure adequate current
carrying capacity. Always follow local building codes.
Ensure the camera is properly grounded. Typical to good grounding practices, the camera chassis
ground should be connected to the lowest resistance path possible. FLIR requires a grounding strap
anchored to the grounding lug on the back plate of the camera housing and connected to the nearest
earth-grounding point.
Note
1.4.2 Video Connection
The analog video connection on the back of the camera is a BNC connector. The camera also
provides an RCA video connector that can be used to temporarily monitor the video output, without
disconnecting the BNC connection.
The video cable used should be rated as RG59U or better to ensure a quality video signal.
1.4.3 GPIO Alarm Connections
The camera can receive a single input signal and can provide a single output signal.
1.4.4 Ethernet Connection
The cable gland seal is designed for use with Shielded Category 6 Ethernet cable.
The terminal blocks for power connections will accept a maximum 16 AWG wire size.
Figure 1-5: GPIO Terminal Plug
Table 1-1: GPIO Connections - J102A
Pin Connection Notes
1Alarm Out1 Relay contact
rated load 0.09 A @ 5 Vdc
2Alarm Out2
3GND
4Alarm In1 –
Dry alarm contact
5Alarm In2 +
1 52 3 4

427-0033-00-12 Version 110 February 2019 13
This document does not contain any export-controlled information.
F-Series ID Camera Installation
1.5 F-Series ID Camera Specifications
Uncooled
Thermal Camera
Array Format 640 × 480
Detector Type Long-Life, Uncooled VOx Microbolometer
Effective Resolution 307,200
Pixel Pitch 17 µm
Thermal Frame Rate NTSC: 30 Hz
PAL: 25 Hz /8.33 Hz
Optical
Characteristics
Model FOV Focal Length
F-608 ID 8.6° × 6.6° 75 mm, f/1.1
F-612 ID 12° × 10° 50 mm, f/1.2
F-617 ID 17° × 14° 35 mm, f/1.1
F-625 ID 25° × 18° 25 mm, f/1.1
F-644 ID 44° × 36° 13 mm, f/1.0
Sensitivity <35 mK @ 25 °C F# 1.0
Spectral Range 7.5 μm to 13.5 μm
Focus Range Athermalized, Focus-Free
Video
Composite Video NTSC or PAL Standard; 1 Vp-p, BNC 75 ohm
switchable from web page. Refer to Video Setup, pg. 34.
Video Compression Two independent channels of streaming H.264 or M-JPEG
Thermal AGC Modes
Optimized Video Analytics AGC Mode and manual controls for
Brightness (ITT Mean/gamma), Contrast (Max Gain), Sharpness
(DDE Gain), and AGC Filter
Video Analytics AGC Mode Engaged when analytics is enabled
Thermal AGC
Region of Interest (ROI)
Default Presets and User definable ROI to insure optimal image
quality for subjects of interest
Analytics Management Web-based configuration and management
Analytics Features
Region Entrance/Intrusion Detection, Crossover/Fence
Trespassing, Auto/Manual Depth Setup, Human and Vehicle
Rules, Hand-off target to PTZ tracking, Tampering
Image Uniformity
Optimization
Automatic Flat Field Correction (FFC) with thermal and temporal
triggers
System
Integration
Ethernet 10/100 Mbps
General Purpose Input/
Output (GPIO)
One dry contact input;
One relay output, rated load 0.09 A @ 5 Vdc
Network API ONVIF Profile S, FLIR SDK, FLIR CGI Library
Supported Protocols IPV4, HTTP, UPnP, DNS, NTP, RTSP, RTCP, RTP, TCP,
UDP, ICMP, IGMP, DHCP, ARP

427-0033-00-12 Version 110 February 2019 14
This document does not contain any export-controlled information.
F-Series ID Camera Installation
General
Weight ~9.5 lb (4.4 kg); Configuration Dependent
Dimensions (L, W, H) 18.1" × 5.5" × 6.3"
(460 × 140 × 160 mm)
Input Voltage 24 Vac (21-30 Vac)
24 Vdc (21-30 Vdc)
Power Consumption 24 Vdc = 10 W (max no heater); 46 W (max w/ heaters)
24 Vac = 15 VA (max no heater); 51 VA (max w/ heaters)
Environmental
IP rating
(dust and water ingress) IP66
Operating temperature range -40 °C to 70 °C (-40 °F to 158 °F) cold start
Storage Temperature range -55 °C to 85 °C (-67 °F to 185 °F)
Humidity 0-95% relative
Vibration IEC 60068-2-27
Mechanical Shock MIL-STD-810F Transportation
De-Icing MIL-STD-810F, Method 521.1;
De-Icing of 3/6mm, model dependent
Compliance and
Certifications
EN 61000-6-4:2007+A1:2011
AS/NZS CISPR 32 Class A:2015
AS/NZS 61000.6.4:2012
ICES-003 Issue 6 Class A:2016
EN 50130-4:2011+A1:2014
EN 55032 Class A:2015
EN 55024:2010+A1:2015
EN 61000-6-4:2007+A1:2011
FCC Part 15, Subpart B, Class A/CFR 47 FCC Class A:2015
IP 66—IEC 60529:2013/EN 60529:1991 + A1:2000
Information Technology Equipment Safety—IEC 60950-1:2005 + Am1:2009 + AM2:2013
EN 60950-1:2006 + Am11:2009 + Am1:2010 + Am12:2011 + Am2:2013
Warranty and
Regulatory
Compliance and
Certifications
FCC Part 15 (Subpart B, class A)
CE Marked
RoHS
IP66
ONVIF Profile S
WEEE
Warranty Camera: 3 years
Sensor: 10 years

2
427-0033-00-12 Version 110 February 2019 15
This document does not contain any export-controlled information.
Basic Operation and Configuration
This chapter provides basic information on how to operate the F-Series ID camera. A bench test can
be used to verify camera operation before the camera is configured for the local network. This chapter
also provides general configuration information.
2.1 IP Camera, ONVIF Profile S Compliant
When the camera is connected to the network it functions as a server; it provides services such as
camera control, video streaming, network communications, and geo-referencing capabilities. The
communications protocol used is an open, standards-based protocol that allows the server to
communicate with a video management client, such as FLIR LatitudeTM or with a third-party VMS
client, including systems that are compatible with ONVIF Profile S. These clients can be used to control
the camera and stream video during day-to-day operations. Refer to the individual product web page at
https://www.flir.com/browse/security/thermal-security-cameras/ for a listing of supported VMS clients
2.1.1 Server Configuration
It may be necessary for the installer to make a limited number of configuration changes to the camera
server, such as setting the IP communication parameters, setting new login passwords, as well as
some scene specific parameters. For example, each camera comes from the factory with the same
default IP addressing (DHCP), so adding more than one camera to an IP network may require each
camera to be configured with a different static IP address. On the other hand, many of the
configuration parameters will remain unchanged from the factory default settings.
2.2 Camera Bench Test
The camera provides both analog video and IP video. Test the analog video at the test connector
(RCA) with the back plate removed. When installing the camera into an analog network, connect the
video cable to the BNC connector. Do not use both video connections simultaneously. Test the IP
communications when performing the bench test. If any image adjustments are necessary, they can be
done using a web browser over the IP connection, and saved as power-on default settings.
Once the camera is connected to a network and powered on, set camera network parameters using
the FLIR Discovery Network Assistant (DNA) software, perform a bench test by using a web browser to
view the video and control the camera, or view video in the local Network Video Management System
(for example, FLIR Latitude).
The FLIR Discovery Network Assistant (DNA) software does not require a license to use and is a free
download from the individual product web page at:
https://www.flir.com/browse/security/thermal-security-cameras/.
• Download the DNA utility.
• Unzip the utility, then double-click to run the executable file ( DNA.exe). All the units on the
VLAN are discovered.
• For additional instructions on using DNA, refer to the DNA User’s Manual available in the Help ( )
link while the software is running.
2.2.1 Set IP Address using the FLIR Discovery Network Assistant (DNA)
The F-Series ID camera is shipped with Dynamic Host Configuration Protocol (DHCP) IP addressing. If
the existing network has a DHCP server, the camera will be assigned an appropriate IP address. If the

427-0033-00-12 Version 110 February 2019 16
This document does not contain any export-controlled information.
Basic Operation and Configuration
network does not have a DHCP server, the camera will default to an IP address of 192.168.0.250.
Configuring the camera for IP communications generally involves the following steps:
Step 1 Connect the Ethernet port of the camera to the existing IP camera network.
Step 2 Connect a PC or laptop to the same network.
Step 3 From the PC connected to the camera network, use the DNA utility to discover and display
the camera’s current IP address.
Step 4 Right-click on the camera, select IP
Setup to change the IP address or select
between static IP or DHCP addressing.
Step 5 Double-click the camera in DNA’s
Discovery List to open the camera’s
web server Login page in a web browser
or point your web browser to the
camera’s IP address.
Step 6 Using the web browser, configure the
camera settings, such as camera date/
time, and other parameters, so the
camera is compatible with the existing
network.
2.2.2 Log in to the Camera Web Page
Use a web browser to connect to the camera’s web server using one of three User Names: user,
expert, or admin (the default passwords are user, expert, and admin respectively).
Important Note
The user login can be used to do the initial bench test of the camera. The expert login may be used
to make configuration changes such as setting the IP address and other server settings. The admin
login has access to all configuration, setup, and maintenance settings.
To prevent unauthorized access, change all of the login passwords (admin login required). For
information on how to change the passwords, refer to Security Options, pg. 28.
Online manual
Select IP Setup
Right-click

427-0033-00-12 Version 110 February 2019 17
This document does not contain any export-controlled information.
Basic Operation and Configuration
Two web sessions can be active at once. An inactive session will be logged out after 20 minutes.
Note
Open a web browser — Google Chrome, Mozilla Firefox, Microsoft Internet Explorer 11, or Microsoft
Edge — and enter the camera IP address. The login screen with a picture of the camera will appear.
Enter admin for the User Name and admin for the Password, and click Log in.
2.2.3 Live Video Page
The Live Video page displays a live image from the camera on the left part of the screen. Along the
top of the screen are some menu choices, including Live Video (the red text indicates it is selected),
Setup, Maintenance, Help, and Log out.
A VMS Remote to the camera, ONVIF or Nexus CGI, uses the same password as the web interface.
Refer to VMS Remote, pg. 46.

427-0033-00-12 Version 110 February 2019 18
This document does not contain any export-controlled information.
Basic Operation and Configuration
On the right side are some control buttons.
The frame rate selector, in the lower right corner of the web page, allows the user to change the
frame rate in the browser from the default 8 fps up to 16 fps. This controls the frame rate of the user’s
own web browser only, and does not affect the video streams to other users or to an NVR. If the live
video is not displayed, refer to Troubleshooting Tips, pg. 30.
Help
The Help menu displays software version information. If it is necessary to contact FLIR Technical
Support for assistance, it will be helpful to have the information from this page on hand. For
information about the factory configuration of the camera refer to the Maintenance > Product Info >
Identification web page (requires Admin login).
Log out
Use this button to disconnect from the camera and stop the display of the video stream. If a web
session is inactive for 20 minutes, it will be stopped and it will be necessary to log in again.
Toggle PC/Camera time
Use this button to display either the PC time or the camera time.
Camera Control and Status
In the lower left of the screen are two indicator lights: Control and Status.
Initially the Control light is off, as in the image above, indicating the user is
not able to control the camera immediately. When multiple users are
connected to a camera, only one user at a time can issue commands to the
camera. If another user has control of the camera, the Control light is yellow.
Figure 2-1: Live Video Web Page – admin login
Toggle Time

427-0033-00-12 Version 110 February 2019 19
This document does not contain any export-controlled information.
Basic Operation and Configuration
A user is able to request control of the camera by clicking on the yellow or
black light, or simply by sending a command to the camera. After a short
pause, the Control light should turn green. Be patient, there may be a slight
delay between each command while the browser waits for a response from
the camera.
If a command is sent to the camera when the user does not have control, the command will not be
executed, and it is necessary to send the command again once the light is green.
Web Control Panel
The control buttons on the right side of the page can control the camera. When the mouse cursor is
positioned over a button, a tool tip is displayed which explains the function of the button.
When the mouse is positioned over the video window, a snapshot
button is shown in the upper right corner of the video image. The
snapshot button will save an image as a .jpg file to the selected
destination folder or as determined by the web browser.
The functions of the buttons appearing for the F-Series ID cameras are described below:
Toggle Polarity
This button changes the way various objects are displayed in the image, for example,
with hot objects displayed as white and cold objects as black, or vice versa.
Toggle Palette
This button causes the IR camera to cycle through different color palettes. Each of the
palettes presents the IR image using a different color scheme. Use the Toggle Polarity
button to invert the palette, for example, between white hot and black hot.
Perform IR NUC Calibration
This button causes the camera to do a manual Non-Uniformity Correction (NUC)
operation. The F-Series ID camera, by default, does an automatic NUC calibration as
required based on changes in temperature.
Save snapshot

427-0033-00-12 Version 110 February 2019 20
This document does not contain any export-controlled information.
Basic Operation and Configuration
Function
When the Function button is selected, the keypad changes
to a numeric keypad. A tool tip can be shown when a
function has been assigned to a number. Use the back
( ) arrow to return to the Control Panel.
Analytics On/Off
The F-Series ID camera Intrusion Detection analytics can be enabled or disabled from the
Live Video page. Detection area and tripwire alarms must be setup prior to use.
Refer to Video Analytics Setup, pg. 38.
De-Ice On/Off
This button will turn the De-Ice heater on or off. The heater will run, controlled by the
thermostat, for approximately one hour unless turned off by the user again selecting the
De-Ice button.
2.3 Basic Camera Configuration
The following procedures describe how to do the most common basic camera configuration steps,
such as setting the camera IP address and hostname and changing the user passwords.
2.3.1 Expert and Admin Accounts
When a user logs in as expert or admin, Setup and Maintenance menus are available. The Setup
menu is used to make adjustments to the camera features.
The basic camera configuration steps are accessed through the Maintenance > Server menu,
using the menus on the left side of the page. The LAN Settings, Services, and Security Options
selections are described below (Maintenance Menu > Server Page, pg. 21). The expert login has
access to the Server pages. The admin login provides access to all configuration options. The login
passwords should be changed (admin login required) to prevent unauthorized access.
2.3.2 Setup Menu
The Setup menu is used for GEO Settings (Latitude and Longitude location), Video setup, thermal
(IR) camera setup, and defining Video Analytics motion detection zones for the F-Series ID camera.
For additional details, refer to Setup Menu, pg. 33.
Adjustments to the IR settings should only be made by someone who has expertise with thermal
cameras and a thorough understanding of how the various settings affect the image. In most
installations, the only camera settings needed are available from the Web Control panel on the Live
Video page (Palettes and Polarity). Haphazard changes can lead to image problems including a
complete loss of video. Additional information is provided in Thermal Image Setup - IR Page, pg. 36.
When making configuration changes using the Setup page, most of the changes take effect
immediately, and it is not necessary to start and stop the server. However it is necessary to save the