FLORABEST HG04678 User manual

IAN XXXXXX
PROGRAMMABLE WATERING TIMER
®
IAN 311538
BEWÄSSERUNGSCOMPUTER
Bedienungs- und Sicherheitshinweise
LAISTYMO KOMPIUTERIS
Nurodymai dėl valdymo ir saugumo
ELEKTRONICZNE URZĄDZENIE
DO NAWADNIANIA
Wskazówki dotyczące obsługi i bezpieczeństwa
PROGRAMMABLE
WATERING TIMER
Operation and safety notes
BEVATTNINGSDATOR
Bruksanvisning och säkerhetsanvisningar

GB Operation and Safety Notes Page 5
SE Bruksanvisning och säkerhetsanvisningar Sidan 27
PL Wskazówki dotyczące obsługi i
bezpieczeństwa Strona 48
LT Nurodymai dėl valdymo ir saugumo Puslapis 71
DE/AT / CH Bedienungs- und Sicherheitshinweise Seite 92

A
C
4
9
11
10
8
SET
B12
13
16
17
15 14
3 4 6 7
18 8
1 2 7 3
6
5

D
9
10
11
1

GB 5
List of pictograms used..............................................Page 7
Introduction.........................................................................Page 7
Intended use..............................................................................Page 7
Scope of delivery......................................................................Page 8
Technical data...........................................................................Page 8
Parts description........................................................................Page 9
Display indicators......................................................................Page 9
Safety.......................................................................................Page 10
Safety instructions......................................................................Page 10
Safety instructions for batteries/ rechargeable batteries .......Page 12
Inserting/replacing batteries..............................Page 15
Initial use...............................................................................Page 15
Operation .............................................................................Page 16
Putting the product into operation............................................Page 17
Setting current time and day of week......................................Page 17
Programming for automatic watering......................................Page 17
Manual operation for watering................................................Page 19
Read/ modify watering programmes ......................................Page 20
Reset...........................................................................................Page 20
Switching 12/ 24 hours display..............................................Page 21
Switching off the display...........................................................Page 21
Battery status display................................................................Page 21
Troubleshooting ..............................................................Page 22

6 GB
Cleaning and Care.........................................................Page 23
Cleaning the filter......................................................................Page 24
Storage ...................................................................................Page 24
Disposal..................................................................................Page 24
Warranty...............................................................................Page 25

GB 7
List of pictograms used
Volt (direct current) Caution! Explosion
hazard!
Observe caution and
safety notes!
Product meets the
applicable European
product-specific
directives
Never leave children
unattended with pack-
aging materials or the
product.
b
a
Dispose of the
packaging and
device in an envi-
ronmentally-friendly
manner!
Programmable
Watering Timer
Introduction
We congratulate you on the pur-
chase of your new product. You
have chosen a high quality prod-
uct. The instructions for use are part
of the product. They contain impor-
tant information concerning safety,
use and disposal. Before using the
product, please familiarise yourself
with all of the safety information
and instructions for use. Only use
the product as described and for
the specified applications. If you
pass the product on to anyone
else, please ensure that you also
pass on all the documentation
with it.
Intended use
This product is designed to control
sprinklers and sprinkler and irrigation
systems. It facilitates the automatic
irrigation of outdoor areas at a

8 GB
programmed time and for a pro-
grammed duration. The product
may save up to 6 programmes for
automatic irrigation. The product
may only be used outdoors. Any
other use or modification to the
product constitutes improper use.
The manufacturer assumes no lia-
bility for damages due to improper
use. This product is not intended
for commercial use.
Scope of delivery
1 Programmable water timer
1 Tap connector
1 Adapter 33.3mm to 26.5 mm
(G1“ to G ¾”)
1 Filter
2 Batteries 1.5V Type AA
1 Instructions for use
Technical data
Model No.: HG04678
Operating
pressure: 34.5–827 kPa
(0.34–8.27 bar)
Max. water
temperature: 40°C
Power supply: 2 x 1.5V
(direct current)
batteries type AA
Flow rate
(at approx.
3 bar water
pressure): approx. 28 l /min
Programmable
Irrigation
time : max. 09:59 h
Manual
Irrigation
time : max. 09:59 h
Water
connection: G¾” (26.5 mm)
or
G1” (33.3 mm)
Protection
class:
IP X4 (splash-proof)

GB 9
Parts description
(Fig. A)
1Union nut ‒ 33.3mm (G 1“)
2Display
3Button
4Button SET
5Rotary control
6Button
7Button (ON/OFF)
8Battery compartment
9Filter
10 Adapter 33.3mm to 26.5 mm
(G1” to G¾”)
11 Tap connector - for connecting
hose and irrigation computer
Display indicators
(Fig. B)
Display Meaning
12 Current time
13
Watering cycle:
24h/2nd/3rd/
4th/5th/6th/7th
correspond to every
24 hours/ every 2/
3/4/5/6/7 days
Display Meaning
14 Current watering
program (1‒6)
15 Program start time
16 Run time - watering
duration
17
Weekday: Current
weekday or pro-
grammed watering
days
18 Battery status
Button for setting
time
SET Button for setting
operation mode
Button for changing
irrigation mode
Button for switching
device (ON/OFF)
Weak battery status
display

10 GB
Safety
Safety
instructions
Damage due to failure
to comply with these
operating instructions
will void the warranty!
We assume no liability
for consequential da-
mages! We assume no
liability for property
damage or personal in-
jury due to improper
handling or failure to
observe the safety inst-
ructions!
KEEP ALL THE SAFETY
ADVICE AND INST-
RUCTIONS IN A SAFE
PLACE FOR FUTURE
REFERENCE!
DANGER TO LIFE
AND RISK OF
ACCIDENT FOR
INFANTS AND
CHILDREN! Never
leave children unsu-
pervised with the
packaging materi-
als. The packaging
material poses a
suffocation hazard.
Keep this product

GB 11
well away from chil-
dren. This product is
not a toy.
This product may be
used by children
age 8 years and up,
as well as by persons
with reduced physi-
cal, sensory or men-
tal capacities, or
lacking experience
and/or knowledge,
so long as they are
supervised or inst-
ructed in the safe
use of the product
and understand the
associated risks.
Children should not
be allowed to play
with the product.
Cleaning and user
maintenance should
not be performed by
children without su-
pervision.
Any repairs during
the warranty period
must be performed
by a manufacturer
authorised service
centre, or the war-
ranty will be void if
subsequent dama-
ges occur.
Always replace de-
fective parts with ge-
nuine spare parts.
Only by using these
parts will you ensure
that the safety requi-
rements are met.

12 GB
Avoid direct sunlight.
Always shut off the
tap if you no longer
use the product
Do not operate the
product near open
flames.
Check the product
and its supply lines
at regular intervals
to ensure that they
are impermeable
and that they func-
tion perfectly.
Do not aim the wa-
ter jet at electrical
equipment!
RISK OF DEATH/
ELECTRIC SHOCK!
Do not aim the water
jet at persons or ani-
mals!
The product is not
suitable for supplying
drinking water.
Safety
instructions
for batteries/
rechargeable
batteries
DANGER TO
LIFE! Keep batter-
ies/rechargeable
batteries out of reach
of children. If acci-
dentally swallowed
seek immediate
medical attention.

GB 13
DANGER
OF EXPLO-
SION! Never re-
charge non-recharge-
able batteries. Do not
short-circuit batteries/
rechargeable batter-
ies and/or open
them. Overheating,
fire or bursting can
be the result.
Never throw batter-
ies/rechargeable
batteries into fire or
water.
Do not exert me-
chanical loads to
batteries/recharge-
able batteries.
Risk of leakage
of batteries/
rechargeable
batteries
Avoid extreme envi-
ronmental conditions
and temperatures,
which could affect
batteries/recharge-
able batteries, e. g.
radiators/direct
sunlight.
If batteries/recharge-
able batteries have
leaked, avoid con-
tact with skin, eyes
and mucous mem-
branes with the
chemicals! Flush
immediately the af-
fected areas with

14 GB
fresh water and seek
medical attention!
WEAR
PROTEC-
TIVE GLOVES!
Leaked or damaged
batteries/recharge-
able batteries can
cause burns on con-
tact with the skin.
Wear suitable pro-
tective gloves at all
times if such an event
occurs.
In the event of a
leakage of batter-
ies/rechargeable
batteries, immedi-
ately remove them
from the product to
prevent damage.
Only use the same
type of batteries/re-
chargeable batteries.
Do not mix used and
new batteries/re-
chargeable batteries.
Remove batteries/
rechargeable batter-
ies if the product will
not be used for a
longer period.
Risk of damage of
the product
Only use the speci-
fied type of battery/
rechargeable battery!
Insert batteries/re-
chargeable batteries
according to polar-
ity marks (+) and (-)

GB 15
on the battery/
rechargeable bat-
tery and the product.
Clean the contacts
on the battery/
rechargeable bat-
tery and in the bat-
tery compartment
before inserting!
Remove exhausted
batteries/recharge-
able batteries from
the product immedi-
ately.
Inserting/replacing
batteries (see Fig. C)
Untighten the screw of the
battery compartment 8co-
ver, remove the cover.
Insert 2 AA batteries (LR06 /
Mignon) into the battery
compartment 8. Observe
correct polarity.
Remark: The display show
all LCD symbols for approx. 1
second and then switch to
„Setting current time and day
of week“ section.
Close the cover and tighten
the screw.
Initial use
The site where the product will be
installed must meet the following
requirements for safe and troub-
le-free operation:
The maximum temperature of
the flowing water is 40°C.
The minimum operating tem-
perature is +5°C.
The maximum temperature of
the environment is +50°C.
Only use clear freshwater.
Only connect the product ver-
tically with the hose connec-
tion 11 pointed downwards
to prevent water from entering
the battery compartment 8.

16 GB
ATTENTION! The irrigation
controller may only be connec-
ted to a drinking water abs-
traction point with a safety
device which corresponds to
TYPE HD at the very least ac-
cording to EN 1717 (back-
flow preventer with tube
ventilation).
Note: Such mains adapters
are available from speciality
retailers.
Check the water connection
type available. The product is
fitted with a union nut 1for
a tap with a 33.3mm thread
(G 1”). For a tap with a
26.5mm thread (G ¾”) use
the adapter supplied 10 .
Insert the filter 9into the
union nut 1as depicted in
Figure A.
For a 26.5mm thread (G ¾”):
Screw the adapter 10 onto
the tap. Do not use any tools
for this purpose.
Screw the union nut 1onto
the thread of the tap or the
adapter. Do not use any tools
for this purpose.
Screw the tap connector 11
onto the hose connection.
You can then connect a hose
to the tap connector 11 .
Open the tap.
ATTENTION! If defects /
leaks arise when using the
adapter 10 , the thread of
the tap must be wrapped
using sealing tape.
Programme irrigation as
described in the chapter
„Operation“.
Operation
Irrigation can be fully automated
at any time of the day using the ir-
rigation controller. A sprinkler,
sprinkler system or drip irrigation
system may be connected.
The irrigation controller automati-
cally carries out irrigation at the
respective programmed start time
and for the programmed dura-
tion. Take the season and time of
the day into consideration when

GB 17
programming. Evaporation and
water consumption is lowest early
in the morning or late in the evening.
Putting the product
into operation
1. Insert batteries to the item as
described in the chapter „In-
serting /replacing batteries“.
2. Connect the water timer to
water tap (see Fig. D).
Setting current time
and day of week
1. Press button 3for approx.
2 seconds (see Fig. 1) (not
necessary if you just insert bat-
teries).
The hour display in the
“Time” section will flash
on screen.
2. Set the time in hours with the
rotary control 5(For example
9 hour) and confirm with the
button 3(see Fig. 2).
The minute display in the
“Time” section will flash on
screen.
3. Set the time in minutes with
the rotary control 5(For ex-
ample 30 minutes) and con-
firm with the
button 3
(see Fig. 3).
The cursor in the “day of
the week” section will flash
on screen.
4. Set the day of the week with
the rotary control 5and
confirm with the
button 3
(see Fig. 4).
Remark: In case you input a
wrong data, you can always press
the (ON/OFF) button 7to go
to previous step.
Programming for
automatic watering
1. Press the SET button 4for
approx. 2 seconds (see Fig. 5).
The program number
display flash on the “Prog”
section will flash on screen.

18 GB
2. Use the rotary button to set
the program number (e.
g. Prog 3) and confirm by
pressing the SET button 4
(see Fig. 6).
The hour display on the
“Start” section will flash
on screen.
3. Set the hours for starting the
watering time with the rotary
control 5(e. g. 6 hours) and
confirm with the SET button 4
(see Fig. 7).
The minute display on the
“Start” section will flash on
screen.
4. Set the minutes for starting
the watering time with the ro-
tary control 5(e. g. 20 mi-
nutes) and confirm with the
SET button 4(see Fig. 8).
The hour display on the
“Run Time” section will
flash on screen.
5. Set the hour for the watering
time and confirm with the SET
button 4(see Fig. 9).
The minute display on the
“Run Time” section will
flash on screen.
6. Set the minutes for the wa-
tering time and confirm with
t
he SET button
4
(see Fig. 10).
The cursor of the “wate-
ring frequency” section
will flash on screen.
The watering frequency
can be selected by:
The watering cycle (right
hand column of the display),
see step 7.
or
The watering days (left
hand column of the display),
see step 8.
7. Select the watering cycle
with the rotary button (e. g.
2nd) and confirm by pressing
the SET button
4
(see Fig. 10).
Remark: 24h/2nd/ 3rd/
4th/ 5th /6th/ 7th means:
Watering every 24 hours/
every 2 /3/ 4 /5/ 6/7
days.
The week preview will be
displayed in the left hand
column.
The display on the “Prog”
will flash on screen.

GB 19
8. Turn the rotary button until the
cursor on the “watering
days” section flash.
Select each watering day
and confirm by pressing the
SET button 4(see Fig. 11).
After select the watering
days, press the
button 6to final confirm.
The display on the “Prog”
will flash on screen.
9. Select the “Prog ON” with
the rotary button and confirm
by pressing the SET button
4(or you can select OFF if
you don’t want to activate the
program at this moment).
After setting up the first pro-
gram, the system will now
jump back to step 2, so you
can set up program No. 2–6.
When you have finished set-
ting up the programs, you
can press the (ON/OFF)
button 7to exit the program-
ming mode and go back to
the normal operation mode.
Remark: In case you input a
wrong data, you can always press
the (ON/OFF) button 7to go
to previous step.
Manual operation
for watering
The valve can be opened or
closed manually at any time.
A program-controlled open valve
can be closed early without chang-
ing the program data (watering
start time, run time and frequency).
1. Press the button 6for
approx. 2 seconds to open
the valve manually (or just
press the button 6to
close an opened valve).
2. Press the SET button 4if
you want to set a specific
duration.
The hour display on the
“Run Time” section will
flash on screen.
3. Set the hour of the watering
time and confirm with the SET)
button 4.

20 GB
The minute display on the
“Run Time” section will
flash on screen.
4. Set the minute of the water-
ing time and confirm with the
SET button 4.
Remark: If you want to quit
setting up the manually watering
mode, you can press the (ON/
OFF) button 7to exit the pro-
gramming and go back to the
normal operation mode.
Remark: If the valve has been
opened manually and a pro-
grammed start of a watering pe-
riod overlaps the manual opening
period, the programmed starting
time is suppressed.
Example:
The valve is opened at 9:00
am manually, the opening pe-
riod is 30 minutes. A program
with a start time between 9:00
am and 9:30 am will not be
undertaken in this case.
Read/modify
watering
programmes
1. In the normal operation mode,
press the SET button 4to
read the programme data.
Use the rotary switch to switch
between Programme 1‒6 to
read the data.
2. To modify the program data,
press the SET button 4after
selecting the program in step
1. After modifying the program
data, the system will go back
to the normal operation mode.
Reset
Press the SET button 4and
button 6at the same time for
approx. 3 seconds. The LCD dis-
play will show all symbols for ap-
prox. 1 second and the system
will restart. All the programmed
data will be erased and restore
to factory setting.