Fluigent FLPG Plus User manual

USER’S
MANUAL
FLPG Plus

CONTENTS
Before the rst use...........................................................
Product Overview..............................................................
Quick Start Guide..............................................................
Output Capacity.................................................................
Specications........................................................................
Technical Support..............................................................
Notes...........................................................................................
3
4
5
8
9
10
11

3
BEFORE THE FIRST USE
Remove the transport screws
under the FLPG Plus.
These screws are used to protect the compressor inside during the
transport.
Please keep these screws in case of future transport.

4
PRODUCT OVERVIEW
The pressure value displayed is in
units of bar (1 bar = 14.5 psi)
The rear pressure output
delivers the same pressure
as the front output. One or
the other can be used for
better tubing management,
or both at the same time
to pressurize two pressure
controllers.

5
QUICK START GUIDE
Please, always place the FLPG Plus on a horizontal and stable surface.
Keep clear for at least 10 cm at sides of FLPG Plus. This allows for
ventilation and the air drying system to function properly.
Start using the FLPG Plus
Supply and power ON the FLPG Plus
1
2Pull out the pressure regulator knob to unlock it
Locked Unlocked (orange ring is visible)

6
QUICK START GUIDE
3Turn the knob to change the output pressure (from 0.1 bar
to 2.30 bar) in order to meet the supply requirement of the
pressure controller channel range.
Different channel ranges require different pressure supply. The
following table shows the cases of Fluigent's pressure controllers.
Flow EZTM
(channel range)
2000
mbar
1000
mbar
345
mbar
69
mbar
25
mbar
Required
pressure supply
2.1 bar 1.1 bar 1.1 bar 0.15
bar
0.15
bar
MFCSTM series
(channel range)
2000
mbar
1000
mbar
345
mbar
69
mbar
25
mbar
Required
pressure supply
2.3*
bar
1.3 bar 0.8 bar 0.5 bar 0.5 bar
The FLPG Plus is designed to work at 2.30 bar or below.
Do not operate above this value, or the output pressure can become
unstable. This may damage the FLPG Plus and the connected devices.
* The MCFS 2000 mbar range channel is compatible with the 2.3 bar supply
pressure, despite its nominal supply pressure of 2.4 bar

7
QUICK START GUIDE
4Connect the pressure controller's pressure inlet to the FLPG
Plus' pressure output (front or/and rear)
5Power OFF the FLPG Plus after use. Doing so will extend service
life of the compressor

8
OUTPUT CAPACITY
Whensetto2.1bartodrivetheFlowEZTM2000mbarchannels(or
2.3bartodriveMFCS2000mbarchannels),theFLPGPluscan
driveupto4channelsatthesametime.
Whensetto1.1bartodrivetheFlowEZTM1000mbarchannels(or
1.3bartodriveMFCS1000mbarchannels),theFLPGPluscan
driveupto8channelsatthesametime.
Whensettolowerpressurestodrivelowerrangechannels(see
tablesonpage6formoreinformation),theFLPGPluscandriveup
to8channelsatthesametime.
The FLPGPlus'outputcapacityisthenumberofchannelsitcandrive
simultaneously.Thiscapacitydependsontheoutputpressureset
withthepressuresettingregulator.
Do not connect more channelsthan thenumbers shown
above. Otherwise, the output pressure may drop and
become unstable, leading to possible damage of  the
FLPG Plus and the connected pressure controller.

9
Product Number: FLPG005
Output pressure: From 0.1 bar to 2.3 bar
Output capacity*: 8Fluigent's1000mbarrangechannels
8Fluigent'sbelow 1000mbarrangechannels
Output capacity*: 4Fluigent's2000mbarrangechannels
Voltage: 24V DC
Current: 1.6 A
Dimensions: 179 x 154 x 264 mm (W x H x D)
Weight: 5.9 kg
Environment: Indoorcleanenvironment
15-25°C
RH<65%(nocondensation)
Lifetime: 10 000h**
SPECIFICATIONS
*Higheroutputcapacityversionexist,consultFluigentsalesrepresentive
**Maintenance is recommended after this duration

10
Or call our technical support team directly
Still have questions? E-mail us at:
support@uigent.com
Interested in Fluigent products ?
For commercial requests, please e-mail:
contact@uigent.com or your local ofce
For tutorial videos about the LineUp
TM
series, please visit Fluigent on YouTube
Fluigent
Fluigent S.A.S [phone]
Fluigent Inc. [phone]
Fluigent GmbH [phone]
For a fully detailed FAQ for all Fluigent products, please visit:
http://www.uigent.com/faqs/
To view the complete Fluigent product line and application notes:
http://www.uigent.com
TECHNICAL SUPPORT

11
NOTES

VERSION
MAR. 2021