Fluke 8808A Configuration guide

Manual Supplement
© 2010-2012 Fluke Corporation. All rights reserved. 

Manual Title: 8808A Calibration Supplement Issue: 4
Print Date: October 2008 Issue Date: 12/12
Revision/Date: Page Count: 2
This supplement contains information necessary to ensure the accuracy of the
above manual. This manual is distributed as an electronic manual on the
following CD-ROM:
CD Title: 8808A
CD Rev. & Date: 3, 12/2009
CD PN: 2713002
.

8808A Calibration Manual Supplement
9/11 1
Change #1
On page 3-11, replace Table 3-8 with the following:
Table 3-8. Frequency Verification Steps
Nominal Input Range 90-Day Test Limit 1-Year Test Limit
Ampl. Freq. High Low High Low
0.1 V 20 Hz 2000 Hz 20.04 Hz 19.96 Hz 20.06 Hz 19.94 Hz
0.1 V 50 Hz 2000 Hz 50.02 Hz 49.98 Hz 50.03 Hz 49.97 Hz
0.1 V 1900 Hz 2000 Hz 1900.24 Hz 1899.76 Hz 1900.26 Hz 1899.74 Hz
0.1 V 19 kHz 20 kHz 19.0023 Hz 18.9977 Hz 19.0025 Hz 18.9975 Hz
0.1 V 195 kHz 200 kHz 195.024 Hz 194.977 Hz 195.026 Hz 194.975 Hz
0.1 V 1000 kHz 1000 kHz 1000.14 Hz 999.86 Hz 1000.16 Hz 999.84 Hz
Change #2
On page 2-6, replace the Current-Input Fuses section with the following:
Current-Input Fuses
The 200 mA and 10 A inputs are protected by user-replaceable fuses.
The 200 mA input is protected by a fuse (F1) rated at 440 mA, 1000 V (fast blow), 10,000 A
minimum breaking capacity.
The 10 A input is protected by a fuse (F2) rated at 11 A, 1000 V (fast blow), 10,000 A
minimum breaking capacity.
Current Input Fuse Table
F1 F1 - Fuse, 11 A, 1000 V, Fast blow or equivalent 803293
F2 F2 - Fuse, 440 mA, 1000 V, Fast blow or equivalent 943121
On page 2-6, under the first Warning replace step 3 with:
Press to set the range to 200 .
On page 2-6, under the second Warning replace step 5 with:
5. Remove the defective fuse and replace it with a fuse of an appropriate rating. See the Current
Input Fuse Table

Manual Supplement 8808A Calibration
2 12/12
Change #3, 64137, 64189
On page 1-4, add the following to the Symbols, table:
Conforms to relevant South Korean EMC Standards.
Conforms to CAN/CSA-C22.2 No. 61010-1, second edition,
including Amendment 1.
On page 1-9, add Electromagnetic Environment and replace Safety and EMC with:
Safety ................................................................ IEC 61010-1, 600 V CAT II / 1000 V CAT I, Pollution Degree 2
Electromagnetic Environment.............. IEC 61326-1, Basic
EMC.................................................................... Applies to use in Korea only. Class A Equipment (Industrial Broadcasting &
Communication Equipment) [1]
[1] This product meets requirements for industrial (Class A)
electromagnetic wave equipment and the seller or user should take
notice of it. This equipment is intended for use in business
environments and is not to be used in homes.