Fluke 9040 Owner's manual

Supplement
© 2013 - 2021 Fluke Corporation. x
All rights reserved.
Title: 9040 Users Supplement Issue: 3
Part Number: 2438546 Issue Date: 11/21
Print Date: April 2005 Page Count: 8
Revision/Date: 2, 5/11
This supplement contains information necessary to ensure the accuracy
of the above Instruction Sheet.

9040 Users Manual Supplement
11/21 1
Change #1, 65800
On page 5, add the following to the Symbols table:
ÃConforms to relevant South Korean EMC Standards.
Change #2, 448, 506
On page 3, add the following Warnings:
•Read all safety information before you use the Product.
•Use this Product indoors only.
•Use only current probes, test leads, and adapters supplied
with the Product.
•Do not use the Product above its rated frequency.
•Do not apply more than the rated voltage, between the
terminals or between each terminal and earth ground.

Manual Supplement 9040 Users
2 11/21
•Do not keep the Product in operation and unattended at high
temperatures.
On page 8, add the following Warning:
XWWarning
To prevent possible electrical shock, fire, or personal injury, do
not operate the Product with covers removed or the case open.
Hazardous voltage exposure is possible.

9040 Users Manual Supplement
11/21 3
On page 5, add the following to the Symbols table:
»Consult user documentation.
On page 5, replace the CAT II, CAT III and CAT IV in the
Symbols table with:
¼
Measurement Category II is applicable to test and
measuring circuits connected directly to utilization points
(socket outlets and similar points) of the low-voltage
MAINS installation.
½
Measurement Category III is applicable to test and
measuring circuits connected to the distribution part of
the building’s low-voltage MAINS installation
¾
Measurement Category IV is applicable to test and
measuring circuits connected at the source of the
building’s low-voltage MAINS installation

Manual Supplement 9040 Users
4 11/21
On page 10, replace the entire page of Specifications, with:
Specifications
Maximum voltage between any Terminal and Earth Ground: 600 V
Power: Supplied by circuit under test.
Fuse: (9040 UK model only) 0.5 A, 1000 V, 50 kA, 6.3 mm x 32 mm
Determine Rotary Field Direction:
Nominal Voltage: 40 to 690 V ac (Ume)
Frequency Range (fn): 15 to 400 Hz
Current Pickup: 1 mA
Nominal Test Current (in each phase): 1 mA
Temperature:
Operating -10 °C to +40 °C
Storage -40 °C to +60 °C
Operating Relative Humidity: 15 % to 80 %
Altitude:
Operating ≤2000 m
Storage ≤2000 m
Size: 12.4 cm x 6.1 cm x 2.7 cm

9040 Users Manual Supplement
11/21 5
Weight: 200 g
Safety:
IEC 61010-1: Pollution Degree 2
IEC 61010-2-030: Measurement CAT III 600 V/CAT IV 300 V
IEC 60925: IP40 (non-operating)
IEC 61557-7: Phase sequence
Electromagnetic Compatibility:
International: IEC 61326-1: Industrial Electromagnetic Environment
CISPR 11: Group 1, Class A
Group 1: Equipment has intentionally generated and/or uses
conductively-coupled radio frequency energy that is necessary for
the internal function of the equipment itself.
Class A: Equipment is suitable for use in all establishments other
than domestic and those directly connected to a low-voltage power
supply network that supplies buildings used for domestic purposes.
There may be potential difficulties in ensuring electromagnetic
compatibility in other environments due to conducted and radiated
disturbances.

Manual Supplement 9040 Users
6 11/21
Caution: This equipment is not intended for use in residential
environments and may not provide adequate protection to radio
reception in such environments.
Emissions that exceed the levels required by CISPR 11 can occur
when the equipment is connected to a test object.
The equipment may not meet the immunity requirements of this
standard when test leads and/or test probes are connected.
Korea (KCC):Class A Equipment (Industrial Broadcasting &
Communication Equipment)
Class A: Equipment meets requirements for industrial
electromagnetic wave equipment and the seller or user should take
notice of it. This equipment is intended for use in business
environments and not to be used in homes.
USA (FCC): 47 CFR 15 subpart B. This product is considered an
exempt device per clause 15.103.

9040 Users Manual Supplement
11/21 7
Change #3, A212
On page 7, in the Determine the Rotary Field Direction:
Delete step 3.