Forest garden Burford BFBGMHD User manual

Gazebo
Fixing Pack (BFGAZFP) Not to Scale
REQUIRED TOOLS :
(NOT SUPPLIED)
POZI DRIVE SCREWDRIVER
STEP LADDER
TAPE MEASURE HAMMER
Issue 0115
PARTS LIST
Important :
Assembly of this
Gazebo requires a
minimum of three
adults.
Must pre-drill for
each screw used.
IMPORTANT, RETAIN FOR FUTURE REFERENCE; READ
CAREFULLY
Check all parts prior to assembly
This building is pressure treated to ensure the longevity of all
timber components and to protect against rot. This may leave
a colour difference on some parts that will even out as the
moisture content stabilises. This will not require additional
treatment.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Due to the nature of the material the doors may need some
trimming for a neater fit.
- Please keep all plastic bags and small parts away from
children
- The roof of this building is not a load bearing structure.
- This product must be built on a solid level base.
Technical Help line: 0333 7777 089 8.30 am and 5.00
pm Monday to Friday.
In line with your statutory rights, please check all parts prior
to assembly, as assembly of damaged parts may be deemed
to be acceptance and this may affect the remedies you are
entitled to. If the product is not constructed in accordance
with the instructions, or is altered in anyway (e.g. painted) the
manufacturer cannot be held liable for any resulting damage.
flush
BAGFL1 Qty 2
BAGRF Qty 6
BAGFL2 Qty 2
BAGBAL Qty 2
BAGRF Qty 6
BABGMP Qty 3
BAAGM Qty 2
BAGPP Qty 3
Arden Gazebo Parts
Burford Gazebo Parts
A B
C
E
BAGRAFC Qty 6
BAGPOST Qty 6
BAGARCH Qty 1
BAGARCH Qty 3
DC
BAGMETHAT Qty 1
BAGFLCAP Qty 6
(floor capping)
BAGFINTOP Qty 1
BAGFINB Qty 1
BGLRFB2 Qty 6
(1296mm roof board)
BGLRFB1 Qty 6
(1224mm roof board)
GBSLAT1075 Qty 3
(1075mm bench slat)
GBSLAT952 Qty 3
(952mm bench slat)
GBSLAT830 Qty 3
(830mm bench slat)
H
Q
I
K
G L M
N
J
P
F
O
R
T
GBBRACE Qty 3
(1075mm bench back brace)
GBFBRACE Qty 3
(734mm bench front brace)
GBSBRACE Qty 12
(330mm bench side brace)
GBSUP Qty 3
(885mm bench support)
GBLEG440 Qty 12
(bench leg)
U
V
WX
S
3
5
1
4
2
F
G
K
E
J
D
C
flush
Place the floor sections
together to create the base
Position and fix each of the floor capping
pieces around the edge of the base using
4 x 30mm nails for each.
Fix the posts to either side of one of the panels
and fix them to each side using 4 x 70mm screws,
screwing through the panel framework first.
flushflush Lip
Make sure that all of the panels are
secured to the posts and are in line with
the outside of the base as shown
(do not fix to the floor at this point)
B
Place the arch
pieces between
the posts so that
they are in line
with the panels.
Fix the arch in
place using 2 x
70 mm screws for
each using the
pre-drilled holes.
Check that all of the sides are flush with the base
before securing each panel to the base using 4 x
70mm screws, screwing down through the framing.
a
b
Silicon Gun and Tube Qty 1
70mm screw Qty 98
45mm screw Qty 138
30mm Nails Qty 24
SPIRIT LEVEL

Forest Garden Ltd, Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
Maintenance.
Regularly check that all fixings are secure.
Regularly check for structural parts for damage.
Regularly check benches are free of splinters.
Fix the remaining rafters to the finial base the same as step 6.
From inside the gazebo fix each rafter to the post by screwing up
through the post, at an angle, into the rafter.
Attention: Make sure that the rafters are secured by another person to
avoid head injury.
6 7 8
910 11
I
L
H
N
M
O
P
Q
R
S
T
U
V
W
X
Fix a rafter to the finial base and make sure that
everything is tight before securing the rafter using a 70mm
screw, screwing at an angle through the rafter in to the
post.
Complete for the opposite side and position the assembly
onto the Gazebo so that the rafters sit into the top of the
posts.
Slide a roof section into place using the grooves on
the rafters. From underneath the roof section fix the
roof to the rafters each side using 2 x 70mm screws
for each side, screwing through the batten first.
Place the metal cap over the finial base
and screw the finial top into place over the
top.
Slot each of the loose roof
boards into the ends of the roof
panels. Secure each board in
place using a 45mm screws for
each end, securing the boards
to the rafters.
Fix each of the bench components to the legs as shown using 2 x 45mm screws
for each end. Use a single screw on each end for the bench support (W).
When placing the bench slats, position the front and back first, making sure
that each is flush on all sides. Again fix these using 2 x 45mm screws for each
end.
When all of the roof
sections have been
secured. Use the silicon
and gun provided to
seal down the side of
each roof.
Attention
Take care when
working at height and
make sure ladders are
anchored
Biocidal Product Regulation (EU 528/2012) Article 58 Information: This article contains biocidal products to give protection against wood destroying insect and wood rotting Fungai.
This article contains timber treated with Tanalith E 3475, incorporating biocidal products to give protection against wood destroying insects & wood rotting fungi.
Contains: Copper carbonate, Tebuconazole and Propiconazole.
Wear gloves when handling freshly treated wood. Avoid breathing dust when cutting treated or untreated wood. Dispose of off-cuts responsibly – do not burn.