Forest garden VENPAVNB User manual

Issue 0117
Forest Garden Ltd. | Unit 288 | Oak Drive | Hartlebury Trading Estate | Hartlebury| Worcestershire | DY10 4JB
This product is pressure to ensure longevity of alltreated
timber components and to protect against rot. This may leave
a colour difference on some parts that will even out as the
moisture content stabilises This will not need additional.
treatment.
nPlease keep all plastic bags and small parts away from
children.
nThe roof of this product is not a load bearing structure.
nTimber is a natural material and will shrink and swell as a
result of varying moisture content.
Assembly of damaged parts may be deemed to be
acceptance and this may affect the remedies you are entitled
to.
If the product is not constructed in accordance with the
instructions, or is altered in anyway (e.g. painted), the
manufacturer cannot be held liable for any resulting damage.
Important:
Please check all parts prior to
assembly.
Attention:
nFor Domestic Use Only.
nMust be built on a andsolid level
base.
nMake sure all screw heads are flush.
nRegularly check that all fixings are
tight and secure.
nMake sure all staples from
packaging are removed.
Pre-drill
for each screw used.
Ladder
Pozidrive
Screwdriver Tape Measure
Spirit Level Saw Rubber Mallet
Not to Scale
Fixing Pack (VENPAVNBFP)
25mm SCREW Qty 320 50mm SCREW Qty 80
150mm SCREW Qty 4
abc
e
Important:
Assembly of this product
requires a minimum of
two adults.
x 2
80mm SCREW Qty 20
d
READ THE INSTRUCTIONS THOROUGHLY
BEFORE ASSEMBLING
100mm SCREW Qty 4
Item Number Part Code Part Description Quantity
1 1201202400PARPTR POST 120x120x2400mm PAR PTREAT 4
3 OSCRAF OUTDOOR STRUCTURE CORNER RAFTER 4
4 88880210FINPTR FINIAL 88x88x210mm PTREAT 1
5 150142695PARA2PTR BOARD 150x14x2695mm PAR ANGLED PTREAT 4
6 150142506PARA2PTR BOARD 150x14x2506mm PAR ANGLED PTREAT 4
7 150142318PARA2PTR BOARD 150x14x2318mm PAR ANGLED PTREAT 4
8 150142129PARA2PTR BOARD 150x14x2129mm PAR ANGLED PTREAT 4
9 150141941PARA2PTR BOARD 150x14x1941mm PAR ANGLED PTREAT 4
10 150141752PARA2PTR BOARD 150x14x1752mm PAR ANGLED PTREAT 4
11 150141564PARA2PTR BOARD 150x14x1564mm PAR ANGLED PTREAT 4
12 150141375PARA2PTR BOARD 150x14x1375mm PAR ANGLED PTREAT 4
13 150141187PARA2PTR BOARD 150x14x1187mm PAR ANGLED PTREAT 4
14 150140998PARA2PTR BOARD 150x14x998mm PAR ANGLED PTREAT 4
15 150140810PARA2PTR BOARD 150x14x810mm PAR ANGLED PTREAT 4
16 150140621PARA2PTR BOARD 150x14x621mm PAR ANGLED PTREAT 4
17 150140433PARA2PTR BOARD 150x14x433mm PAR ANGLED PTREAT 4
18 124140244PARA2PTR BOARD 124x14x244mm PAR ANGLED PTREAT 4
19 120282456PARA2NIPTR BOARD 120x28x2456mm PAR ANGLED NOTCHED PTREAT 4
20 120481680PARNIIA2PTR RAFTER 120x47.5x1680mm PAR NOTCHED TWICE ANGLED PTREAT 4
21 120282400PARNIIPT BOARD 120x28x2400mm PAR NOTCHED 4
22 120240146PAII45PT BOARD 120x24x145mm PAR ANGLED PTREAT 16
23 90900658PAII45PT BRACE 90x90x658mm PAR ANGLED PTREAT 8
PARTS LISTPARTS LIST

Fix the top outer ring of fascias so that they sit on the lip of the
posts and all meet up at the ends.
Fix the boards using 2x50mm screws at each end.
Position and mark out the ground so that the posts will be
2220mm apart from the notches as shown.
1
2
1
Attention:
Before you begin construction we recommend that you place
all the parts in the order that you will use them. Read
carefully through the steps of the instructions first.
2220
We recommend the use of spikes to anchor these into the ground.
b
level

21
The internal ring is interlocking.
Start by positioning and lining up the back and sides first. Fix the back
section using 2x50mm screws at each end screwing into the posts.
Using a rubber mallet gently tap the boards until the notches are
locked.
Use a spirit level along the length of each post to make sure the product
is still level and square.
When all of the sections are in place secure them to the posts with
2x50mm screws for each end.
b
x2
3
4
b
x2
b
Fix the feet covers around the base of the posts, making sure that
they are flush and line up tightly. (May need to trim)
Fix each cover in place using 2x50mm screws, offset.
22

Issue 0117
Forest Garden Ltd. | Unit 288 | Oak Drive | Hartlebury Trading Estate | Hartlebury| Worcestershire | DY10 4JB
Help line: 08:30 to 17:00 Monday to Friday0333 7777 089
23
4
3
Fix two of the rafters to the finial at right angles, screwing through the finial into
the end of the rafters with a single 100mm screw for each.
Lift the rafters on top of the pavilion and line the notches up. You will need a
person on a ladder in the middle of the structure to keep the rafters in place and
use small adjustments to make sure they are level and at the correct pitch.
Fix these in place screwing down through each rafter into the post using a 150mm
screw.
Place and fix the two remaining rafters against the finial fixing them by screwing,
at an angle ,through the top of the rafter into the finial using 1x100mm screw for
each.
Place the braces so that they are flush and tight against the
post and level with the top of the fascia as shown. Fix the brace
to the post using 2 x 80mm screws and to the fascias using
1x50mm screw through each side.
Again use a spirit level and adjust as required.
b
C
x2
b
level
level
d
e
6
5
d

20
Slide the stepped rafters into position. Use a rubber mallet to tap
the rafter in place making sure that it is sat correctly in the
notches.
Fix the middle stepped rafters to the other corner rafters using an
80mm screw, through the top step.
c
7
Starting from the top and working down secure each of the boards
to the rafters and the stepped rafter using 2x25mm screws.
The top, smallest board will only need 1x25mm screw for each
end.
8
aa
a
a
Hint: Use the smaller of the
roof boards to line up the top step
of the stepped rafter against the
top step of the corner rafters.