Sunjoy L-GZ215PST-5B User manual

DO NOT RETURN TO RETAILER
IF YOU HAVE ANY QUESTIONS OR CONCERNS
PLEASE VISIT OUR WEBSITE AT:
www.sunjoyonline.com
OR TOLL FREE AT:
8:00 AM EST to 8:00 PM PST
Production Number：2018xxxx
1-866-578-6569
SUNJOY GROUP INTERNATIONAL PTE LTD
619 Slack St reet
Steubenville, Ohio 43952 USA

WARNING:
1.Assembly Instructions must be followed.
2. Gazebo must be secured / anchored when fully assembled.
Note: DO NOT assemble this item alone for safety. Four people are necessary.
SAFETY INFORMATION:
Please read and understand this entire manual before attempting to assemble or install the product.
When installing and assembling the item, it is recommended four or more adults are involved.
This product is intended for outdoor use only and should be placed on flat, horizontal ground.
Ensure enough clearance around the product.
Do not use the unit during an electrical storm, as there is a remote chance of getting struck by lightning.
Do not climb on top of the item. Falling off it can result in serious injury, possibly evendeath.
This package contains small items and plastic bags that should be kept away from children.
Ensure all connectors and poles are firmly secured in position. It is important to do so before use to avoid
collapsing or damage to the item, which could also result in injury.
Never barbecue under this item or use lanterns that contain open flames.
Center hook’s maximum weight capacity is 26 lbs.
WARNING:
Keep all flame and heat sources away from the tent fabric. This tent is made with fabric that meets CPAI-84
specifications for flame resistance. It is not fire proof. The fabric will burn if left in continuous contact with any
flame source. The application of any foreign substance to the tent fabric may render the flame -resistant
properties ineffective. Remove the roof during severe weather conditions such as sustained strong winds,
hurricanes, tropical downpours and snow. The manufacturer or retailer is not liable for any loss of the product
ASSEMBLY INSTRUCTIONS
ITEM# L-GZ215PST-5B
SKU# 164707
10’x12’ HAMPTON GAZEBO
THIS UNIT IS HEAVY!

or other items due to the failure to take down the item during any inclement weather.
CARE AND MAINTENANCE:
1. This item is intended for decorative and sunshade purposes only, and is not designed to withstand severe
weather, including high winds, sustained tropical downpours, and snow. In order to avoid damage in such
instances, remove any accumulated water and the roof immediately. Disassemble the item in the reverse
order of the assembly steps if necessary prior to a severe storm.
2. A partially disassembled item is not stable enough to resist high winds and other severe weather, and
therefore can be damaged and/or cause damage.Complete disassembly is recommended prior to any major
storm.
3. Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.
4. Steel components of garden accessories and furniture are treated with rust inhibiting paint. However, due to
the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural
process. To minimize this condition, it is recommended that care be taken when assembling and handling the
product, in order to prevent the paint from being scratched.
5. Surface rust can be removed easily using a very light application of common cooking oil. If surface
oxidation (rusting) occurs and no measures are taken to correct it, the oxidation may start dripping onto the
assembly surface, which may cause damaging stains that may bedifficult to remove.
6. If the product will not be used for a long period (e.g. winter time), it should be stored in a clean, dry
environment.
7. Keep the original packaging to store the item.
PREPARATION:
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents
list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Item Identification: For ease of identification, all parts are labeled to correspond to the Step number in which
the part is used.

1
4
4
4
2
2
2
2
4
8
4
4
2
2
4
4
1
1
4
1
1
1
1
Post
Post Base
Base Protector
Short Beam (1)
Short Beam (2)
Long Beam (1)
Long Beam (2)
Slanting Bar Connector
Support Bar
Big Top Bar
Connect Bar
Short Side Bar
Long Side Bar
Long Netting Bar
Short Netting Bar
Big Top Connector
Hook
Small Top Connector
Small Top Bar
Small Canopy
Large Canopy
Wall
Mosquito Netting
E
A
B
C
D
F
G
H
I
J1
J2
K
L
M
N
O
P
Q
R
S
T
U
V
Parts List
P11144B01100
P11651A01100
P11539A01100
P11042C01100
P11043C01100
P11044C01100
P11045C01100
P10737A01100
P11884A01100
P10307B01100
P11477A01100
P10478A01100
P10479A01100
P12155A01100
P12156A01100
P10107B01100
P12601C01100
P10108B01100
P10248A01100
P00149B07007
P00150B07007
P00216B06007
P00331B01911
Part NO.
QTY
CS NO. Image
Description

Fig.1: Fit the base protector (C) onto the post (A), connect the post base (B) and post (A) by using screw
(AA) and flat washer (BB).
Fig.2: Insert the beam E (G) to beam D (F), and fix them by using bolt (CC) and washer (BB).
Fig.3: Connect assembled beams to the post (A) by using bolt (DD) and washer (BB).
AA M6X15 screw 8 PCS
BB M6 flat washer 64 PCS
CC M6X15 bolt 40PCS
DD M6X35 bolt 16 PCS
Z M6 wrench 1 PC
Hardware Pack 1
H09015C11
H19001C11
H02015C11
H02035C11
H00001C12
Part NO. QTY
CS NO. ImageDescription

Fig.4: Attach the netting bar N (M) to beam D (E, F, G) by using bolt (CC) and washer (BB).
Fig.5: Fix the support bar (I) to beam G (D, E, F) and post (A) by u sing bolt (CC) and washer (BB).
BB M6 flat washer 28 PCS
CC M6X15 bolt 4 PCS
EE M6X40 screw 12 PCS
FF M6 nut 12 PCS
Hardware Pack 2
H09040C11
H14001C11
Part NO. QTY
CS NO. Image
Description

Fig. 6: Insert the connect bar (J2) to the big top bar (J1), fix them by using bolt (CC) and washer (BB).
Fig.6-1: Insert the big top bar (J1) to the big top connector (O). Screw the hook (P) to big top connector (O).
Fig.7: Attach the connect bar (J2) to the post (A) by using screw (EE), washer (BB) and nut (FF).
Fig.8: Insert the short side bar (K) and long side bar (L) to the big top connector (O).
Fig.9: Attach the side bar K (L) to the slanting bar connector (H) by using screw (EE), washer (BB) and nut
(FF).
Fig.10: Insert the small top bar (R) to the small top connector (Q), then place the small canopy (S) onto the
small top and tighten.
Fig.11: Place the large canopy (T) onto the big top, do not spread it. Attach assembled small top to the big
top bar (J1) by using screw (EE) , washer (BB) and nut (FF). Then s pread the large canopy (T) and tighten.
GG Φ8X180 peg 16 PCS
HH Small plastic ring 52 PCS
II Big plastic ring 52 PCS
Hardware Pack 3
P12401A01001
P90701A07001
P90701B07007
Part NO.
QTY
CS NO. Image
Description

`
Made in China
Fig.12: Hang the m
osquito netting (V) to the netting bar N (M ) by using Small
plastic ring (HH).
Fig.13: Hang the
w all (U) to the beam (F, D, E, G) by using Big plastic ring (II).
Fig.14: Lift the base protector (C), secure the assembled gazebo to lawn with
Peg (GG ).
Now, your Gazebo is ready for use.