Forest garden MTGSH64 User manual

Tongue and Groove
6' x 4' Shed
Issue 0315
B
MTGSH64DE
DOOR END
DE F
J
MTGSH64 PARTS LIST
MTGSH64DR
DOOR
MTGSH64RF
ROOF QTY 2
G
Place the corner strips so that they cover the joins
between the panels. Fix each in place using 3x30mm
screws.
Place the panels on top of the floor. Make sure that all the panels are tight and flush
before fixing them to each other using 3x50mm screws.
When the panels are secured to each other, make sure they are square and fix to the
floor using 3x50mm screws for each side panel. Use 2x50mm screws for the plain and
door end panels, ensuring that the screws are located into the bearers underneath.
Top View
D
B
A
2
4
11
C
MTGSH64WS
WINDOW PANEL
Place and secure two hinges to the door so that they line up with
the battens on the reverse, using 25mm Security Screws for each.
Place the door into the door end ensuring that the door is square.
Fix the doors in place using 3x25mm Security Screws for the
smaller section of each hinge.
3
C
Fixing Pack (FPMTGSH64) Not to Scale
REQUIRED TOOLS :
(NOT SUPPLIED)
POZI DRIVE SCREWDRIVER
SPIRIT LEVEL
TAPE MEASURE HAMMER
Tee Hinge Qty 2
40mm Screw Qty 2
I
30mm Screw Qty 40
E
IMPORTANT, RETAIN FOR FUTURE REFERENCE; READ
CAREFULLY
Check all parts prior to assembly
This buildings is pressure treated to ensure longevity of all
timber components and to protect against rot. This may leave
a colour difference on some parts that will even out as the
moisture content stabilises. This will not require additional
treatment.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Please keep all plastic bags and small parts away from
children
- The roof of this building is not a load bearing structure.
- This product must be built on a solid level base.
Technical Help line: 0333 7777 089 8.30 am and 5.00
pm Monday to Friday.
In line with your statutory rights, please check all parts prior
to assembly, as assembly of damaged parts may be deemed
to be acceptance and this may affect the remedies you are
entitled to. If the product is not constructed in accordance
with the instructions, or is altered in anyway (e.g. painted),
the manufacturer cannot be held liable for any resulting
damage.
XT623502
ACRYLIC SHEET
H
Important : Assembly of
this shed requires a
minimum of two adults.
HAMMER
Must Pre drill for
each screw used.
ROOF FELT
95120760PAII66PT
BARGE BOARD
MTGSH64PS
PLAIN SIDE
MTGSH64PE
PLAIN PANEL
FIN20510012PPT
FINIAL
QTY 2
57121680PPT
CORNER STRIP 1680mm
QTY 4
FELT42BL
FELT QTY 1 ROLL
28280760PAII24PT
DRIP STRIP
MTGSH64FL
FLOOR
A
K M I
D
Attention:
Take care
when placing
the screws.
These can
not be
backed out.
Fix the pad bolt to the doors so that it is in line with the batten on the back. Make sure that both parts are
positioned so that the bolt will locate correctly and keep the doors locked. Fix the pad bolt in place using
8x25mm Security Screws.
Attention:
Take care when placing
the security screws.
These can not be
backed out.
Cranked Hinge
Qty 2
10mm Felt Tacks
Qty 100
25mm Countersunk
Security Screws Qty 22
Pad bolt
Casement Stay
SHARP KNIFE
FOR ROOFING FELT
50mm Screw Qty 24
I
I
MTGWIN
WINDOW
15120629PAII45PT
629mm BEADING QTY 2
15120508PAII45PT
504mm BEADING QTY 2
N OL
25mm Panel Pins Qty 14
25mm Screw Qty 16

10
Forest Garden Ltd, Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
Biocidal Product Regulation (EU 528/2012) Article 58 Information
This article contains timber treated with Celcure AC-500, incorporating biocidal products to give protection against wood destroying insects & wood rotting fungi.
Contains: Basic copper carbonate (Copper (II) carbonate – Copper (II) hydroxide (1:1)), Boric acid, Benzalkonium chloride.
Wear gloves when handling freshly treated wood. Avoid breathing dust when cutting treated or untreated wood. Dispose of off-cuts responsibly – do not burn.
67
Place and fix the Casement Stay centrally against the inside of the opening
window and make sure it is offset at least 12mm from the to top of the frame so
as not to hit the glass. Fix in place using 2 x 25mm screws.
Mark the position of the holes of the casement stay when the window is closed
before fixing the pins in place using the 25mm screws provided.
Place the Drip Strip against the door end above door, fixing it in place using
2 x 50mm screws.
Place each of the roof sections on to the top of the shed so that each section is flush
with the door and plain ends. They should also be in line with the apex.
Fix each roof section in place using 3 x 30mm screws at each end and a 40mm screw
mid way down the side screwing through the board into the top of the side panel.
5
8
Unroll the felt and cut it in to two equal lengths. Place the sheets on each side so
that there is a 50mm overhang on the eaves and they overlap at the apex. Fix these
to the roof using felt nails spaced in 150mm intervals. Cut and fold the corners
securing with a single felt nail for each.
Place the Barge Boards against the front and back of the shed. Make sure
that these are in line with the roof sheet and meet at the apex. Fix each in
place using 2 x 30mm screws.
Place the Finial over the top of the join between the two barge boards and
fix this in place using 2 x 30mm screws.
9
M
F
H
KL
Place the acrylic sheet inside the window frame and position the beading so that each
section fits flush and keeps the sheet tight. Fix each piece using 3 x Panel Pins.
Fix two Flush hinges to the top of the window so that it sits in the rebate. Fix the
smaller section of the hinge to the window using 2 x 25mm screws for each. Open up
the hinges and fix the remaining section of each hinge to the top of the Window Panel
using another 3 x 25mm screws for each hinge.
J
N
M
O
12mm Offset
Maintenance.
Regularly check that all fixings are secure.
Regularly check the quality of the roofing felt and that it is free of holes and splits.