FPG INLINE 5000C Series User manual

Refrigerated
Open-front Cabinets
Curved and Square Formats

Part No. 26126 Rev. P September 2019 - 2 - 5000 Series Open Front Cabinets
Copyright © September 2019 Future Products Group Limited.
All rights reserved.
No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior
written permission of Future Products Group Ltd.

IN-5C08/12-OF - 3 - © Future Products Group
Warnings
Operational
Safety
This appliance is not intended for use by young children or infirm persons,
unless they have been adequately supervised by a responsible person, to
ensure that they can use the appliance safely.
Young children should be supervised, to ensure that they do not play with the
appliance.
Water
THIS UNIT IS NOT WATERPROOF. DO NOT USE A WATER JET SPRAY TO
CLEAN THE INTERIOR OR EXTERIOR OF THIS CABINET.
Caution
Do not store explosive substances, such as aerosol cans with flammable
propellant, in this appliance.
Mains Supply
Cord
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons, in order to avoid a hazard.
Specialist
Disposal
Specialist disposal procedures are required for the safe removal of refrigerant
gasses and potentially flammable foam materials.
Pentane, Dimethyl Ether, Isobutene, Butane and Propane may be present.
Hazardous
Substances
The cabinet does not contain any of the following, in its construction:
Asbestos
PCBs (Oils containing polychlorinated biphenyl)
Mercury

Part No. 26126 Rev. P September 2019 - 4 - 5000 Series Open Front Cabinets
Table of Contents
WARNINGS.........................................................................................................................3
Operational Safety...................................................................................................................................... 3
Water.......................................................................................................................................................... 3
Caution ....................................................................................................................................................... 3
Mains Supply Cord..................................................................................................................................... 3
Specialist Disposal ..................................................................................................................................... 3
Hazardous Substances .............................................................................................................................. 3
INTRODUCTION .................................................................................................................7
Welcome........................................................................................................................................................... 7
Future Products Group (FPG).................................................................................................................... 7
Guidance and Help..................................................................................................................................... 7
Warranty ........................................................................................................................................................... 7
Warranty Period.......................................................................................................................................... 7
Liability Exceptions..................................................................................................................................... 8
Specific Exclusions..................................................................................................................................... 8
Assessment................................................................................................................................................ 8
Time Limit................................................................................................................................................... 8
Caution ....................................................................................................................................................... 8
OPERATION .......................................................................................................................9
Cabinet Layout................................................................................................................................................. 9
Self Service Cabinet................................................................................................................................... 9
Shelf Lighting.............................................................................................................................................. 9
Controls............................................................................................................................................................ 9
Control Panel.............................................................................................................................................. 9
Temperature Controller ............................................................................................................................ 10
Temperature Controller Adjustment ......................................................................................................... 10
Preparation..................................................................................................................................................... 10
Shelf Location and Ticketing .................................................................................................................... 10
Shelf Adjustment ...................................................................................................................................... 11
Caution ..................................................................................................................................................... 11
Power Supply ........................................................................................................................................... 11
Defrost Cycle............................................................................................................................................ 11
Load Cabinet............................................................................................................................................ 11
Loading Restrictions................................................................................................................................. 12
Close Rear Doors..................................................................................................................................... 12
Turn on Lights........................................................................................................................................... 12
Operating Routines ....................................................................................................................................... 13
After Hours ............................................................................................................................................... 13
Cleaning ................................................................................................................................................... 13
De-frost Cycle........................................................................................................................................... 13
TROUBLE SHOOTING .....................................................................................................14

IN-5C08/12-OF - 5 - © Future Products Group
CLEANING........................................................................................................................15
Cautions ......................................................................................................................................................... 15
Power ....................................................................................................................................................... 15
Water........................................................................................................................................................ 15
Exterior ........................................................................................................................................................... 15
Metal Surfaces.......................................................................................................................................... 15
Glass ........................................................................................................................................................ 15
Sliding Doors............................................................................................................................................ 15
Louvers..................................................................................................................................................... 15
Interior............................................................................................................................................................. 16
Internal Glass ........................................................................................................................................... 16
Trays, Shelves & Air Grills........................................................................................................................ 16
Access to the Cabinet Base Cavity .......................................................................................................... 16
Caution ..................................................................................................................................................... 16
Cleaning the Base Cavity......................................................................................................................... 17
Condensate Drain..................................................................................................................................... 17
Cooling Fins.............................................................................................................................................. 17
Temperature Probes................................................................................................................................. 17
Condensate Tray...................................................................................................................................... 17
Mandatory Cleaning Routines...................................................................................................................... 18
Warning .................................................................................................................................................... 18
Removable Filter ...................................................................................................................................... 18
Condenser Radiator ................................................................................................................................. 18
Fault Correction........................................................................................................................................ 18
INSTALLATION ................................................................................................................19
Regulations .................................................................................................................................................... 19
Compliance with Local Requirements...................................................................................................... 19
Setting Up....................................................................................................................................................... 19
Unpacking................................................................................................................................................. 19
Site Preparation........................................................................................................................................ 19
Cabinet Preparation.................................................................................................................................. 19
Shelf Trays ............................................................................................................................................... 19
Grounding................................................................................................................................................. 20
Power Supply and Earthing...................................................................................................................... 20
Electrical Isolation..................................................................................................................................... 20
Condensate Disposal ............................................................................................................................... 20
Location.......................................................................................................................................................... 20
Ventilation................................................................................................................................................. 20
Access...................................................................................................................................................... 20
SERVICING.......................................................................................................................21
Lighting........................................................................................................................................................... 21
Caution ..................................................................................................................................................... 21
Test Lighting Components ....................................................................................................................... 21
Access to LED Strips................................................................................................................................ 21
LED Strip Replacement............................................................................................................................ 21

Part No. 26126 Rev. P September 2019 - 6 - 5000 Series Open Front Cabinets
Refrigeration .................................................................................................................................................. 22
Caution ..................................................................................................................................................... 22
Ventilation Panels..................................................................................................................................... 22
Control Gear............................................................................................................................................. 22
Condenser Radiator ................................................................................................................................. 22
Cabinet Air Circulation Fans..................................................................................................................... 22
Condensate Disposal ............................................................................................................................... 23
Remote Condensers................................................................................................................................. 23
ACR Fault Finding Guide ......................................................................................................................... 23
Temperature Regulator XR40CX ............................................................................................................. 24
XR40CX Connections .............................................................................................................................. 30
SPECIFICATIONS.............................................................................................................31
Mechanical ..................................................................................................................................................... 31
Electrical......................................................................................................................................................... 31
Controller Setting .......................................................................................................................................... 32
Dixell XR40CX Settings............................................................................................................................ 32
Compliance .................................................................................................................................................... 33
Standards ................................................................................................................................................. 33
Performance Aspects............................................................................................................................... 33
Improvements ................................................................................................................................................ 33
Ongoing Development.............................................................................................................................. 33
ELECTRICAL CIRCUIT DIAGRAMS................................................................................34
Model: IN-5C08-OF (Curved)................................................................................................................... 34
Model: IN-5C08-OF-SQ (Square)............................................................................................................. 34
Model: IN-5C12-OF (Curved)................................................................................................................... 35
Model: IN-5C12-OF-SQ (Square)............................................................................................................. 35
SPARE PARTS .................................................................................................................36
Cabinet Serial Number............................................................................................................................. 36
MECHANICAL DRAWINGS..............................................................................................38
Cabinet Dimensions ...................................................................................................................................... 38
IN-5C08-OF.............................................................................................................................................. 38
IN-5C08/5C12-OF-SQ.............................................................................................................................. 39
IN-5C12-OF.............................................................................................................................................. 40

IN-5C08/12-OF - 7 - © Future Products Group
INTRODUCTION
Welcome
REFRIGERATED CABINETS - INTRODUCTION
Future
Products
Group (FPG)
Welcome to the world of FPG! Our innovative products are designed and
engineered to have the best visual merchandising performance.
We are confident that you will be delighted with your inline food service cabinet,
and that it will become a valued appliance in your store.
Guidance and
Help
To ensure you receive the utmost benefit from your new cabinet, there are two
things you can do.
•Before operating the cabinet, please read the instruction book carefully and
follow its recommendations. The time taken will be well spent! These
instructions, both general and technical, tell you how to operate and look
after your food service cabinet so that you can receive the full benefits that
this cabinet has to offer.
•These instructions cannot, however, cover all eventualities. If you are
unsure of any aspect of the installation, operation or performance of your
cabinet, contact your dealer or FPG. Contact details will be found on the
back cover of this manual. In many cases a phone call could answer your
question.
Warranty
REFRIGERATED CABINETS - INTRODUCTION
Warranty
Period
Future Products Group Limited warrants, to the original purchaser of an FPG
manufactured food service cabinet that for ONE YEAR (12 months), from the
date of purchase, any defect in workmanship or material resulting in the product
malfunctioning while under correct use will be rectified.
The warranty is extended to THREE YEARS (36 months), for refrigeration
condenser units. Conditions apply, see Liability Exceptions.
Liability under this warranty is limited to replacing or repairing a part, without
charge.
Continued on next page

Part No. 26126 Rev. P September 2019 - 8 - 5000 Series Open Front Cabinets
Warranty cont.
REFRIGERATED CABINETS - INTRODUCTION
Liability
Exceptions
Liability under this warranty does not include:
•Any loss, damage, or expenses directly or indirectly arising from the use of,
or inability to use, the product or from any other cause.
•Any part of the cabinet which has been subject to misuse, neglect,
alteration, incorrect installation, accident, or damage caused by
transportation, use of abrasive or caustic chemicals, flood, fire or acts of
God.
•Damage, resulting from failure to have the cabinet regularly serviced every
three months, by a refrigeration engineer. NB: You may be required to
provide copies of service records in the event of a compressor failure.
•Any damage or malfunction, resulting from the use of non-FPG supplied
spare parts.
Specific
Exclusions
The following are specifically excluded from warranty:
•Breakage of glass or plastic components, or the replacement of LED lighting
assemblies or gaskets.
•Maladjustment of the electronic refrigeration controller, by an unqualified
person.
•Failure to re-assemble the cabinet correctly after cleaning.
•Fair wear and tear.
Assessment
The liability under this warranty is dependent on an assessment by FPG, to
determine the defect in workmanship or materials.
Time Limit
FPG does not guarantee that any service to be performed under this warranty
will be carried out within any particular time limit.
Caution
No warranty claim will be accepted, unless authorised by FPG prior to
commencement of service.

IN-5C08/12-OF - 9 - © Future Products Group
OPERATION
Cabinet Layout
REFRIGERATED CABINETS - OPERATION
Self Service
Cabinet
This open front cabinet is designed for the display of chilled food items or
drinks.
Cabinets are available either with curved fronts, or in square format.
Sliding glass doors are fitted to the rear of the cabinet.
The cabinet is fitted with three shelves, and items may also be placed on the
base tray.
The internal temperature of
the cabinet is maintained by a
curtain of cold air, emitted
from a grill below the pelmet
of the cabinet.
The pelmet is heated to avoid
external condensation.
Shelf Lighting
All cabinets are fitted with a top light and lighting below each shelf.
Cabinets are fitted with high efficiency LED lighting, requiring no maintenance.
Controls
REFRIGERATED CABINETS - OPERATION
Control Panel
The control panel is mounted on the back of the cabinet, and houses:
•The main power switch
•The Light switch
•The refrigeration controller
The refrigeration controller displays the internal temperature of the cabinet
during normal operation.

Part No. 26126 Rev. P September 2019 - 10 - 5000 Series Open Front Cabinets
Controls cont.
REFRIGERATED CABINETS -OPERATION
Temperature
Controller
The controller regulates the cabinet
temperature and controls the automatic
defrost cycles.
The display indicates the internal temperature
of the cabinet.
On integral condenser cabinets, the refrigeration gas pressure is also
monitored, to protect the compressor from damage resulting from a blocked
radiator or loss of gas.
Temperature
Controller
Adjustment
Caution:
This controller
should only be
adjusted by a
qualified service
technician.
The controller is set up during manufacture of the cabinet, and should not
require further adjustment.
The set point temperature will be lower than the air temperature inside the
cabinet, because the refrigeration condenser is controlled in response to the exit
air temperature from the evaporator heat exchanger.
Incorrect adjustment can cause the fins to ice up, resulting in reduced airflow
and poor performance.
The controller also governs the de-frost cycles, and incorrect adjustment can
again lead to poor temperature control or possible overflow of condensate.
If you think an adjustment may be needed, call the service technician.
Preparation
REFRIGERATED CABINETS - OPERATION
Shelf Location
and Ticketing
All shelves are adjustable in height and can easily be
moved up or down, to match product size.
The movement is restricted to 50mm, because of the
electric cables to the lights. For greater movement
contact the manufacturer or supplier for advice, as
electrical modifications may be required.
The front and rear edges of the shelves
are profiled to carry ticketing/labels.
Continued on next page

IN-5C08/12-OF - 11 - © Future Products Group
Preparation cont.
REFRIGERATED CABINETS -OPERATION
Shelf
Adjustment
To move the shelf support brackets, remove the rear sliding doors and then
remove all the shelves. Using two people, one on each bracket, slide the
bracket upwards and disengage it from the support pillar. Insert the bracket in
the new position and push it down
firmly. Replace all shelf trays and
doors.
The brackets can be inserted in two
positions, allowing the shelves to be
either horizontal or sloping
downwards.
Caution
Make sure the shelf brackets are pushed down as far as they can go.
Otherwise, the shelf may collapse, when loaded with product.
Power Supply
Ensure that power is connected to the cabinet.
Turn on the main power switch, as shown above. The cabinet fans will run
and the cabinet temperature will begin to fall.
The temperature controller is pre-set to maintain the cabinet temperature to 2-
4C, and should not need adjustment.
Defrost Cycle
Note that the defrost times are set from when the cabinet is first turned on.
If they are required at a particular time, you must turn on the cabinet 2 hours
before the first defrost required. The time depends on the cabinet type, see
Controller Settings.
The cycles will then occur every 2 hours, provided that the cabinet remains on.
Load Cabinet
Load the cabinet with pre-chilled product, from either the front or rear doors.
The cabinet is designed to maintain the temperature of pre-chilled product at
between 2and 4C. It is not a refrigerator, and consequently, if warm
product is introduced, there could be some delay before the operating
temperature falls to the normal operating level.
Continued on next page

Part No. 26126 Rev. P September 2019 - 12 - 5000 Series Open Front Cabinets
Preparation cont.
REFRIGERATED CABINETS - OPERATION
Loading
Restrictions
It is important to leave adequate free
space for the refrigerated air to circulate
within the cabinet.
Product should be kept clear of the
lightened areas, shown in the picture.
A minimum clearance of 40 mm should
be maintained below the shelves and
the top air vane.
The internal air grills at the front and
rear of the cabinet must not be covered
at all.
Close Rear
Doors
It is important to keep the rear doors closed. If doors are not fully closed, the
correct air circulation will not be achieved within the cabinet.
Turn on Lights
When ready for service, turn on the cabinet lights.

IN-5C08/12-OF - 13 - © Future Products Group
Operating Routines
REFRIGERATED CABINETS - OPERATION
After Hours
Ideally, cabinets should not be turned off after hours or at night. Products can
either be left in the cabinet or placed in night storage. Shut the cabinet doors
and turn off the lights. The cabinet will then operate on minimum load, and stay
cold, ready for instant operation when next required.
If the cabinet is turned off, allow it to run for about half an hour before replacing
the pre-chilled products.
Cleaning
Since the cabinet needs to be switched off during cleaning operations, it is best
to clean it at the end of the working day. The cabinet will then have time to
recover its normal operating temperature, before replacing the products.
Once the cleaning is finished, turn the cabinet on again, turn off the lights and
shut the doors. The cabinet will cool down under minimum load and be ready
for the next day’s use.
De-frost Cycle
The cabinet will de-frost automatically 12 times per day. The cabinet should
NOT be temperature tested within ½ hour of a de-frost cycle being completed.
The first defrost cycle will occur 2 hours after the cabinet is first switched on.
See Controller Settings.
If you suspect that the defrost system is not working properly, have it checked
by a qualified service person.
Operators must not attempt to adjust the refrigeration controller.

Part No. 26126 Rev. P September 2019 - 14 - 5000 Series Open Front Cabinets
TROUBLE SHOOTING
FAULT
POSSIBLE CAUSE
REMEDY
Cabinet does not operate/start
The mains isolating switch on
the wall, circuit breaker or
fuses are off at the power
board
Turn isolating switch circuit
breaker or fuses on
The power switch on the
cabinet is OFF
Turn the power switch ON
The power switch on the unit is
faulty
Have the switch replaced
HA2 Alarm Display on
Controller
Compressor discharge pipe
high temperature
Turn power off, clean
condenser radiator & pre-filter.
Turn power on.
If no cooling, or alarm returns
within 24 h, call for service.
The cabinet temperature is not
correct
One or more rear doors is
open
Close the doors and re-test
temperature after 30 minutes
Ventilation louvers are blocked
Remove blockages
Product is blocking air louvers
Place product on shelves
Evaporator coil fins are
blocked
Remove blockages
Trays are obstructing air flow
Re-position trays on shelves
Thermostat needs adjustment
Adjust controller
Ambient temperature > 25C
Adjust store air conditioning
Evaporator coil iced up
De-ice coil
Condenser radiator blocked
Remove dust and debris
Thermostat faulty
Replace controller
Temperature probe damaged
or dislocated
Replace or relocate the
temperature probe
Fan not operating
Check and replace the fan
The cabinet lights are not
working
The light switch is OFF
Turn the light switch ON
A LED strip has failed
Replace the LED assembly
An LED PSU has failed
Replace the PSU
An internal circuit breaker has
tripped/failed
Check the wiring and reset
or replace the circuit breaker
Doors are not sliding smoothly
The door is not in its track
Install the door correctly
There is debris in the track
Clean the door tracks
A door glider is damaged or
missing
Have the glider replaced
Lack of lubrication
Apply food grade lubricant to
door tracks
External Condensation
Power supply failed (800 cab.)
Replace power supply
Aluminium parts are corroded
Damage by caustic detergent
Order replacement parts
Service
Personnel Only
The table entries in italics indicate actions to be taken only by qualified Service
Personnel.

IN-5C08/12-OF - 15 - © Future Products Group
CLEANING
Cautions
REFRIGERATED CABINETS - CLEANING
Power
ALWAYS TURN THE POWER SUPPLY OFF BEFORE CLEANING.
Water
THIS UNIT IS NOT WATERPROOF. DO NOT USE A WATER JET SPRAY TO
CLEAN THE INTERIOR OR EXTERIOR OF THIS CABINET.
Exterior
REFRIGERATED CABINETS - CLEANING
Metal Surfaces
Stainless steel or aluminium surfaces should be cleaned with hot soapy water.
DO NOT clean surfaces with abrasive pads or cleaners, as stainless steel and
aluminium surfaces will be damaged.
Glass
All glass should be cleaned using a good quality glass cleaner and a clean
cloth.
DO NOT use abrasive pads or cleaners, because they will damage the surface
of the glass.
Sliding Doors
Sliding glass doors can be removed for cleaning by sliding
the door to central position, placing hands either side of
the door, lifting up and then swinging out at the bottom.
When replacing doors, make sure that the top is located in
the correct slot, and the bottom is
properly located on the correct bottom
track.
Sliding door tracks should be
vacuumed out regularly to keep doors
sliding freely. Failure to do so will
damage the gliders and track.
Louvers
To maintain the refrigeration efficiency, and prevent overheating, use a vacuum
cleaner to remove dust and fluff from the ventilation louvers.
The condenser radiator must also be cleaned regularly, see the Mandatory
Cleaning Routines section.

Part No. 26126 Rev. P September 2019 - 16 - 5000 Series Open Front Cabinets
Interior
REFRIGERATED CABINETS - CLEANING
Internal Glass
The internal glass surfaces can normally be cleaned after the shelf trays have
been removed.
The shelf lights are connected with plugs and sockets, enabling the complete
shelf assemblies to be removed.
Only remove the lights, shelf brackets and rails when carrying out longer term
maintenance.
Trays, Shelves
& Air Grills
Stainless steel trays, shelves, grills etc. should be cleaned with hot soapy water.
Do not use abrasive pads or cleaners as these may damage surfaces.
Warning: Dishwasher detergents will damage any anodised aluminium parts.
Access to the
Cabinet Base
Cavity
Remove the front ticketing rail from the
deck trays, if fitted.
Lift out the deck trays and sweep out, or
use a vacuum cleaner, to remove any
loose debris.
After removing two screws, the fan deck can be
lifted, to enable thorough cleaning.
Lift the cover plate off the
evaporator coil, raising it
to the vertical position, to
disengage it from the
chassis.
Lift the air louvers out.
Caution
The whole of the cabinet interior is now accessible
for cleaning.
To avoid possible damage when replacing fan decks,
be sure that cables are not trapped by metal parts.
Continued on next page

IN-5C08/12-OF - 17 - © Future Products Group
Interior cont.
REFRIGERATED CABINETS - CLEANING
Cleaning the
Base Cavity
Sweep out, or use a vacuum cleaner, to remove any debris from the cabinet
base cavity.
A Wet-and-Dry vacuum cleaner should be used, since there is likely to be some
water in the bottom. Finally, wipe out the bottom with a damp sanitized cloth.
Condensate
Drain
Make sure that the condensate drain is free of debris.
The drain hole is located in the well, at the front of the cabinet, under the return
air grill.
Cooling Fins
If there is food stuck in the cooling fins, it is best
to use a wet and dry vacuum cleaner to suck out
the food. DO NOT attempt to hose food parts
from fins.
Caution: The fins are very sharp. Take extra
care when cleaning this area. Do not bend the
fins over, as this would restrict the air flow and
degrade cabinet performance.
Temperature
Probes
Take care not to damage or move
the temperature probes, when
cleaning the cooling fins.
One probe is inserted between the
fins of the cooling coil another is in
free air. A third probe is located on
the other side of the coil, in the
return air flow.
Do NOT move the probes.
Condensate
Tray
The condensate boil off heater is only designed to handle cooling-coil defrosting
liquid that drains from the well.
DO NOT fill the well with liquid, or attempt to hose out as the condensate tray will
overflow and leak onto floor.

Part No. 26126 Rev. P September 2019 - 18 - 5000 Series Open Front Cabinets
Mandatory Cleaning Routines
REFRIGERATED CABINETS - CLEANING
Warning
It is mandatory to have the radiator fins cleaned periodically, by a
refrigeration engineer. (see Servicing section).
To maintain optimum performance, cleaning must be regular and thorough.
It is recommended that a schedule of cleaning operations be established.
Failure to carry out routine cleaning/servicing schedules will void the
warranty on the refrigeration equipment.
Removable
Filter
(integral
condenser
cabinets)
The removable filter must be kept clean, to maintain
efficient refrigeration performance.
Slide the filter out to remove dust and fluff, using a
vacuum cleaner.
It can also be carefully washed in warm soapy
water.
Condenser
Radiator
For efficient refrigeration performance of cabinets with
integral condensers, the condenser radiator must be
kept clean, (see Servicing, Condenser Radiator).
Accumulated dust and fluff.
Fault
Correction
If any small faults are noticed, have them attended to promptly by a competent
serviceman. Don’t wait until they cause a complete breakdown.

IN-5C08/12-OF - 19 - © Future Products Group
INSTALLATION
Regulations
REFRIGERATED CABINETS - INSTALLATION
Compliance
with Local
Requirements
It is very important that your inline food cabinet is installed correctly and that the
operation is correct before use. Installation must comply with local electrical,
health & safety and hygiene requirements.
Setting Up
REFRIGERATED CABINETS - INSTALLATION
Unpacking
Unpack and check unit for damage and report any damage to the carrier and
supplier. Report any deficiencies to your supplier.
All display cabinets are supplied fully assembled, but the shelf trays are packed
separately.
Site
Preparation
Ensure the cabinet location and any bench cut outs are made to the precise
measurements shown in the Mechanical Drawings. Position the cabinet in its
allocated working position.
Rotate the feet to adjust the cabinet height, and use a spirit level to ensure the
cabinet is level from side to side and front to back. (If this is not carried out,
water may accumulate in the cabinet well, and uneven temperature distribution
could also occur).
Cabinet
Preparation
Remove all tapes, ties and packers, used
to prevent movement during transit.
Lift out the deck trays and grills to gain
access to the cabinet well.
Shelf Trays
If packed separately, remove the shelf trays from their packing, peel off any
protective plastic coating and assemble them on the support members.
Continued on next page

Part No. 26126 Rev. P September 2019 - 20 - 5000 Series Open Front Cabinets
Setting Up cont.
REFRIGERATED CABINETS - INSTALLATION
Grounding
THIS APPLIANCE MUST BE GROUNDED TO EARTH
The earth lead, in the mains cable, must always be connected to ground.
Terminals are also provided, to allow the cabinet to be bonded to a surge
grounding conductor or to adjacent equipment.
Power Supply
and Earthing
The cabinet is supplied with a three-core mains lead, with phase, neutral and
earth conductors. Before connecting to the power supply, check that the local
supply is correct to that shown on the rating label on the rear of the cabinet.
Electrical
Isolation
An accessible means of isolation must be provided in the electrical supply to the
cabinet.
Condensate
Disposal
On the integral condenser versions, no
drain is required for condensate disposal.
Check that there is no packing material or
debris in the integral condensate boil-off
tray.
The element is automatically controlled,
only operating when water is detected in
the tray.
The condensate must be piped to a drain on the remote condenser versions.
A P-trap must be included in the pipe work, to prevent air entering the bun.
Location
REFRIGERATED CABINETS - INSTALLATION
Ventilation
Adequate ventilation must be provided for cooling air to enter and exit through
the rear louvers of the cabinet.
The rear of the cabinet should not be placed close to a wall.
The cooling system is designed to maintain the correct temperature, providing
the rear doors are kept closed and cabinet is not in a draughty location.
Access
Access to the back of the cabinet is also required for loading, cleaning, re-
positioning of shelves and operation of the control panel.