Freescale Semiconductor DEMO9S08SE8 User manual

8-bit Microcontroller
DEMO9S08SE8
The General Purpose 8-bit MCU
Development System
DEMO9S08SE8—Quick Start Guide
• Quick Start Guide
• Lab Tutorials
• CodeWarrior™ Manual
• Getting Started DVD

Get to know the
DEMO9S08SE8 board
Figure 1. DEMO9S08SE8
MC9S08SE8
MCU
Embedded
BDM Multilink
for Programming
and Debug
Power Select
Jumper
MCU Reset
Push Button
MCU Port
LEDs
RS232 Port
Push Buttons

Introduction
Do more with less. The MC9S08SE8 offers a new
level of integration in a 28-pin 8-bit MCU plus
excellent compatibility with Freescale’s 5V MCU
portfolio. This quick start guide provides step-
by-step instructions that within minutes will help
you get started on your next project using the
DEMO9S08SE8 demo board.
DEMO9S08SE8—Quick Start Guide

Step-by-Step Installation Instructions
Please take a look at the
DEMO9S08SE8 labs document
(DEMO9S08SE8LAB) included in
the “Training” section of the DVD to
learn more about the key benefits
the SE8 gives your application.
Install CodeWarrior™
for Microcontrollers and
MC9S08SE8 Service Pack
CodeWarrior is a powerful tool designed to help
you speed your time to market. CodeWarrior
installation is a one-time step required before
connecting the board to your computer. After
installing the MC9S08SE8 Service Pack for
CodeWarrior Development Studio 6.2, it can
support SE8 application development.
1. Insert provided DVD into your computer. A menu
will appear.
2. Click “Install CodeWarrior.”
3. Follow the on-screen instructions until installation
is complete.
4. Return to DVD menu and click “Install SE8
Service Pack,” which is listed under the
software menu.
5. Follow the on-screen instructions until installation
is complete.
Following installation, take advantage of several
CodeWarrior tutorials that will walk you through
various development tool features, such as
“C Programming,” “Assembly Programming,”
“Using Processor Expert” and more. Simply
open CodeWarrior via “Programs > Freescale
CodeWarrior > CW for Microcontroller V6.2
> CodeWarrior IDE.exe,” click “Run Getting
Started Tutorial” from the startup dialog, select
a tutorial and follow the on-screen instructions.
STEP
1

Open DEMO9S08SE8
Documentation
The Getting Started DVD included with the
demo board kit contains a folder with demo
board documentation. This folder should be
copied onto your computer for use in the
next steps. This installation step is a one-time
requirement.
1. Insert provided DVD into your computer. A
menu will appear.
2. Click “DEMO9S08SE8 Documentation,” which
is listed under the Documentation menu,
to start downloading the DEMO9S08SE8
documents.
3. Follow the on-screen instructions to complete
the installation.
For your reference, the documentation contains:
• CodeWarriorprojectles
• Demoboardschematics
• Demoboarduser’smanual
STEP
2
DEMO9S08SE8—Quick Start Guide
STEP
3
Connect Board to
Computer and Launch
the Demo Program
USB driver installation is a necessary one-time
step that requires CodeWarrior installation first.
1.Removeboardfromanti-staticpouch.
2.Makesurethejumpersareinthedefault
positions. Please refer to the LAB Tutorial to
checkthedefaultjumperpositions.
3.ConnecttheprovidedUSBcablefroma
free USB port on your computer to the USB
connectorontheboard.
4.Theoperatingsystemwillrecognizeyourboard
as new hardware and will prompt you to install
the USB drivers. Choose the recommended
option to install the software automatically.
USBdriversforyourboardwerepre-loaded
via CodeWarrior Development Studio 6.2
installation.
5. Follow on-screen instructions until all USB
driver installations are completed. The on-
boardgreenUSBLEDshouldilluminate.

STEP
4
Test Board by Running
Quick Start Application
Now that you have successfully completed the
software and hardware setup, test your board
by running the Quick Start Application, which
is pre-loaded in the microcontroller’s on-chip
flash memory.
1.UsethejumperPWR_SELonthe
DEMO9S08SE8boardtoselectyourpower
source,jumperVDDforexternalpoweror
jumperVBforpowerthroughUSB.Once
connected, the green VDD LED will illuminate
and the application will run.
2. Once the application has run, LED1 and LED2
begintoblinkalternately.
3.Nowthatyourboardisfunctional,tryoutthe
labsintheDEMO9S08SE8labstutorialtolearn
moreabouttheMC9S08SE8microcontroller
andthefeaturesincludedwithyourboard.

DEMO9S08SE8—Quick Start Guide

Learn More: For more information about
Freescale products, please visit
www.freescale.com.
Freescale and the Freescale logo are trademarks or registered
trademarks of Freescale Semiconductor, Inc. in the U.S. and other
countries. All other product or service names are the property of their
respective owners. © Freescale Semiconductor, Inc. 2008.
Doc Number: DEMO9S08SE8QSG / REV 0
Agile Number: 926-24592 / REV A