Frisco 252045 User manual

6-PANEL CONVERTIBLE PLASTIC PLAYPEN
DIVIDER WITH WALL MOUNTS
INSTRUCTION MANUAL
SKU# 252045
PN# 26320

For questions, please call 1-800-672-4399.
DOG PLAYPEN ASSEMBLY INSTRUCTIONS
Gloves suggested to avoid injury during assembly. Please assemble on a flat surface, and be careful not to scratch the floor.
INSTALLING SKID-RESISTANT PADS
INSTALLING BETWEEN TWO WALLS
NOTE: When setting up as a barrier, maximum number of panels is six. WARNING: Do not mount gate hinges into sheetrock or
plaster. Hardware is included for use in solid materials, such as wood or metal. Never mount the gate at the top of the stairs.
8 Screws (G)Carry Strap (D)
Preassembled Panels (C)
Mounting
Connector (B)
12 Skid-Resistant Pads (F)2 Wall Hinges (E)
Mounting
Connector (A)
PARTS INCLUDED
21 3
STEP 1 Position both of the preassembled
wall mounting connectors/wall hinges,
vertically so the wall hinge pins are facing
upwards on the wall, and the mounting
connector is as close to the floor as
possible. Mark the top of each wall hinge.
See Figure 3.
To help protect floors, ensure the skid-resistant pads
are on the bottom of the gate panels. Clean and dry
the panels prior to installing the pads. Remove a single
pad from the release paper as shown in Figure 1. Place
the adhesive side of the pad onto the bottom edge
of the gate panel approximately 2" from the center of
each hinge, as shown in Figure 2. Repeat steps for each
of the remaining pads. Maximum skid-resistance will
be maintained by cleaning the bottoms of the pads
periodically with a water-dampened clean cloth.
STEP 2 Separate the mounting
connectors from the wall hinges by
pressing inward on the locking boss
located in the center of the wall hinge.
Lift up on the connectors to free them
from the wall hinge. See Figure 4 for
removal from wall hinge.
STEP 3 To attach the wall hinge to the
wall, align the top with the mark drawn
in Step 1. Mark the top hole and pre-drill
a 1/8" pilot hole. Attach the top of the
wall hinge in place with a screw. Proceed
down the hinge and install a screw into
each screw hole with screws provided.
FIGURE 1
FIGURE 4 FIGURE 5FIGURE 3
FIGURE 2

For questions, please call 1-800-672-4399.
REMOVAL FROM WALL HINGE TO DISCONNECT PANELS
INSTALLATION AS A FREESTANDING ENCLOSURE
STEP 4 Attach the mounting connector
side A to panel 1 by setting opening A over
Pin B, push down in order to slide Pin C
into the slot of Cylinder D. See Figure 6.
To remove the gate from the wall hinge, press on the locking
boss located on the center of the wall hinge (See Figure 9), and
lift the panel itself until the gate rib clears the locking boss.
To disconnect two adjoining panels, select one of the joints where
the panel pushes down (panel 1), as shown in Figure 10. Gently
press down on panel 1 while lifting slightly on panel 2. This will
enable you to slide Pin C free of Cylinder D (see Figure 10). Then
lift up on panel 1 until Opening A (see Figure 10) is free of Pin B.
Begin setting up your enclosure by unsnapping the gray carrying strap and carefully unfolding the panels to form a hexagon. See
Figure 11. When you have finished unfolding the panels, there will be two unconnected panels arranged as shown in Figure 12.
Make certain that the pin in Cylinder B is up as shown. Begin connecting the panels together by gently lifting up on panel 2 and
setting the Opening A (as shown in Figure 12) over Pin B located on panel 1.
Now locate the slot on the lower end of Cylinder D. See Figure 12. This slot tapers to an opening that
accommodates Pin C. Gently press down on panel 2 while aligning Pin C with the slot in Cylinder D.
While maintaining downward pressure on panel 2, lift slightly on panel 1, and slide Pin C through the
slot and into the opening as shown.
STEP 5 Attach the mounting connector
side B to panel 2 by setting opening A
over Pin B, push down in order to slide
Pin C into the slot of Cylinder D. See
Figure 7.
STEP 6 Attach the mounting connectors,
that are now attached to the panels, to
the wall hinges by aligning the horseshoe
shaped hoops on one side of the gate over
the pins on the wall hinges to set the gate
in place. See Figure 8. NOTE: Always lift up
on the end panels to ensure that the gate is
properly secured and locked in place.
54 6
FIGURE 6
FIGURE 11
FIGURE 9
FIGURE 12
FIGURE 10
FIGURE 7 FIGURE 8

• STOP using when a pet can climb over yard or dislodge/open the gate.
• Install only with the locking/latching mechanism securely engaged.
• To prevent falls, NEVER use at top of stairs.
• This product will not necessarily prevent all accidents.
• Periodically check all fasteners to be sure they are tight and secure, stop using if any parts are missing or become damaged.
• Wall mount hardware is included for use in solid materials only, such as wood or metal.
• NEVER leave anything in the pet yard that could provide a foothold or create a danger of suffocation or strangulation.
• Do not use this product on a smooth slippery surface unless skid-resistant pads are used (included).
• Do not attempt to use this product in temperatures less than 40 degrees F, or damage may result.
• Do not use as a barrier for stairways, stoves or heaters.
• Do not use on uneven surfaces.
• When setting up as an enclosure, do not connect more than 8 panels. When setting up as a barrier, maximum number of panels is six.
WARNINGS AND CAUTIONS
We care about the safety of your pet, so please READ AND FOLLOW ALL INSTRUCTIONS before using.
Improper use may result in serious injury or even the death of your pet.
CALL OUR FRIENDLY CUSTOMER SERVICE TEAM ANYTIME.
WE’RE HERE 24/7! 1-800-67-CHEWY (672-4399)
QUESTIONS?
Your gate is manufactured from durable, weather-resistant plastic panels. To clean, wash the panels with mild, non-abrasive detergent,
rinse with clean water, and allow to dry thoroughly.
CLEANING TIPS
PET DOOR OPERATION FOLDING FOR TRANSPORT OR STORAGE
Your gate comes from the factory with the pet door in the
locked position.
TO UNLOCK Squeeze and twist the front center knob located
below the pet door. As you twist, the knob will line up with the
arrows on the right or left sides of the knob. The pet door will
move freely in both directions for your pet to pass through.
TO LOCK Squeeze and twist the front center knob located
below the pet door. As you twist, the knob will be in the upright
position, keeping the door securely locked.
Your gate folds compactly for transport or storage. You must,
however, fold the panels properly. Gently fold the panels (without
jerking them or slamming them together) in alternating directions
like an accordion.
Slip one end of the gray carrying strap through the mesh near the
top middle of each outside panel and snap it closed.
The gate is now ready for transport or storage.