Front Runner SSDR011 User manual

SSDR011_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
Universal Drawer
Small SUV
SSDR011
ENG
1
Thank you for purchasing Front Runner Universal Drawer Small SUV.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

SSDR011_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
10MM
10MM
1 1 X Universal Drawer Large Pick-up
2 X Set Of Keys
2 4 X Eye Nut
3 4 X M8 Nylon Washer
4 4 X Stud Plate
5 4 X D-Ring
6 4 X M6x19x1ss Flat Washer
7 4 X M6 Spring Washer
8 4 X M6x20 Hex Bolt
9 4 X Carabiner Hook 60mm
10 4 X M6 Wing Nut
11 4 X Turnbuckle
12 4 X M6 x 30 Countersink Screw
13 4 X M6 Finishing Washer
FIGURE 1.1
13MM
GET ORGANIZED
1
IN THE BOX
Here is what you are looking at for SSDR011
17
1
4
3
2
5
6
7
8
9
10
11
12 13

SSDR011_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 3
FIT AND SECURE
2
6
2.1
2.2
2.3
Secure the 4 D-Rings (item 5) on both
sides of the drawer using the fasteners
shown.
Assemble each of the 4
turnbuckles (item 12) with a wing nut
(item 10) as shown. The wing nut will be
used to lock the turnbuckles after they
have been set.
Place the drawer in the vehicle
and position as desired. Making
sure the turnbuckles are pulling
outward to prevent the drawer
from moving after it has been secured.
5
6
7
8
10MM
9
11
10

SSDR011_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 4
FIT AND SECURE
2
Connect the C-hooks (item 9) onto the
D-rings (item 5) on the drawers upright.
Connect the turnbuckles (item 11) on the
other side of the C-hooks and hook it into
the tie-down that are fitted to the
vehicle.
Secure the drawer by tensioning the
turnbuckles until there is no more
movement on the drawer. Make sure the
drawer stays in position when doing this.
Lock the turnbuckles with the wing nuts.
Do this by tightening the wing nuts up to
the turnbuckles.
Refer to diagram 2.2
2.4
2.5
4
3
2
9
5
11
Assemble the eye-nuts (item 2) with a
M6 nylon washer (item 3) and a stud plate
(item 4) and slide them into place.
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!