Front Runner FAJK003 User manual

ENG
Jeep Wrangler JKU 4 Door (2007-Current)
Front Support arms
FAJK003_REV_A01 © COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
1
IMPORTANT WARNING!
FAJK003
FRONT RUNNER CAN NOT RECOMMEND A MAXIMUM LOAD CARRYING CAPACITY. PLEASE REFER TO YOUR VEHICLE MANUFACTURER'S RECOMMENDATIONS. IT IS CRITICAL
THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN
AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS
TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU
DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE
INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
Thank you for purchasing Front Runner Jeep Wrangler JKU 4 door Front Support Arms .
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

FAJK003_REV_A01 © COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS 2
IN THE BOX
FIGURE 1.1
1 2 X M8 x 20 Hex Bolt
2 2 X M8 x 19 x 2SS Flat Washer
3 2 X M8 Nyloc Nut
4 2 X Front Support Arm - 1Left + 1Right
5 2 X M8 Nut Cap
6 1 X Rubber Strip 600mm
IN THE BOX TOOLS NEEDED
IN THE BOX
1GET ORGANIZED
T40
3
5
6
2
1
4RH
4LH

© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
3 FAJK003_REV_A01
4LH
6
PREP FOR RACK INSTALL (FULL RACK)
2
13mm
2.1
2.2
2.3
If not already assembled, assemble your
Tray as per the Universal Tray Assembly
Instructions (Document RRSTUNI)
Using a T40 Torx Wrench, remove the six
bolts holding the Window Corner Plates in
place. Be careful not to let the plate fall
when removing the last bolt as this may
result in damage to the paintwork of the
part or your vehicle.
Before removing the paper backing from
the Rubber Strip (Item 6), cut five pieces
of 60mm long and apply it to the inside of
each Front Support Arm as shown.
Tighten the Front Support Arms (Item 4LH
& 4RH) over the window corner plates
using the original bolts.
T40
T40
NOTE: Before fitting the Wind
Deflector, insert two M8 x 16 Hex
Bolts (Item 16 from FAJK006) or
(Item 1 from FAJK003) into the first
slat (Combined Slat), using the
Machined slots. Slide a bolt to each
of the outer corners.

© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
4 FAJK003_REV_A01
MOUNT YOUR TRAY
2
13mm
2.4
2.5
With the help of a friend, flip the Tray
end over end so that it is in the upright
position. (The Tray is flipped end over
end so that bolts and brackets do not
slide left and right).
With one of you on either side of the
Tray, lift the Tray and walk it into
position above the vehicle, approaching
from either the front or the rear of the
vehicle.
Line up the Front Support Arms (Items
4L & 4R) with the two M8 x 16 Hex Bolts
(Item 1) either side of the wind deflector
and hand tighten the front of the Tray to
the arms using M8 Nyloc Nuts and M8 x
19 x 2SS Flat Washers (Items 2 & 3).
2
3
4L
1
Full Rack Shown

© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
5 FAJK003_REV_A01
4
COMPLETION
3
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
9
3.1
Congratulations! You did it. Take a step back and admire your work!
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on: