Front Runner SSDR012 User manual

SSDR012_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
drawer pick-UP
medium
SSDR012
ENG
1
45 min
IMPORTANT WARNING!
Thank you for purchasing a Front Runner Drawer.
Before you start, take a moment to familiarize yourself with this Fitting Intruction and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH.
YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE.
THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE.
IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES,
YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

SSDR012_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
10MM
10MM
1 1 X Drawer
2 6 X M6 Stud Plate
3 6 X M8 Nylon Washer
4 6 X M6 Eye Nut
5 8 X M6x20 Hex Bolt
6 4 X M6 Spring Washer
7 12 X M6x19x1 Flat Washer
8 8 X D-Ring
9 1 X Track
10 2 X M8x16 Hex Bolt
11 2 X M8 Spring Washer
12 2 X M8 Flat Washer
13 2 X M8 Channel Nut
14 4 X 60mm C-Hook
15 4 X M6 Wing Nut
16 4 X Turnbuckle
17 4 X M6 Nyloc Nut
FIGURE 1.1
13MM
6.5MM
GET ORGANIZED
1
IN THE BOX
Here is what you are looking at for SSDR012
9
10
5678
76
5
2
1
5
7
8
7
17
3
4
11
12
13
5
7
8
7
17
16
15
14

SSDR012_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS 3
FIT AND SECURE
2
9
13
75
8
6
57
4
3
2
8
6
12
11
10
2.1
2.2
2.3
Slide 2 channel nuts into the track. Center
the track under the drawer and secure with
the fasteners that are shown.
Secure the 4 D-Rings on both
sides of the drawer as shown.
Assemble the 6 eye-nuts and
slide into place.

SSDR012_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS 4
FIT AND SECURE
2
8
7
17
5
16
16
15
15
14
14
Assemble each of the 4
turnbuckles with item 15
as shown. Item 15 will be used
to lock the turnbuckles after they
have been set.
Place the drawer into the vehicle
and position as desired. Making
sure the turnbuckles are pulling
outward to prevent the drawer
from moving after it has been secured.
Mark and drill 6.5mm holes using
the D-rings as a guide.
Use the fasteners that are
shown to secure the drawer
to the vehicle.
2.4
2.5
2.6

SSDR012_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS 5
Congratulations you have completed your installation, take a step back and admire your work.
COMPLETION
3
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
3.1