Front Runner VACC120 User manual

VACC120_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
front runner
VACC120
ENG
1
Thank you for purchasing a Front Runner Suzuki Jimny Internal Cargo Tray.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
Suzuki jimny internal cargo tray

VACC120_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
IN THE BOX
1 1 X Internal Cargo Tray
2 2 X Side Brackets
3 6 X M6 X 12 Button Head Bolt
4 6 X M6 X 12 X 1 Flat Washer
5 4 X M6 X 16 Button Head Bolt
6 4 X M6 X 19 X 1 Flat Washer
7 2 X Short Molle Panel Straps
8 2 X Long Molle Panel Straps
4mm
Phillips
3 4
1
2 5 6
7
8

VACC120_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE2
2.1
2.2
2.3
Insert the M6 x 12 button head bolts (Item 3)
and M6 x 12 x 1 Flat washers (Item 4) into
the side brackets (Item 2) as shown but do
not thread all the way.
Remove the rear grab handles in the vehicle
by removing two mounting screws. Fit
the side brackets (Item 2) using the grab
handle mounting points. The side brackets
can either be fitted using the M6x16 Button
Head Bolts (Item 5) and the M6 x19 x 1 Flat
Washers (Item 6) as seen in Fig 2.2A, or it
can be mounted by refitting the grab handle
as seen in Fig 2.2B.
The slot in the side brackets allows for
adjustment of the tray towards the front
or rear of the vehicle. Use the indication
markers on the side bracket as reference
points to ensure that the left and right hand
brackets are aligned.
With the Front Runner sticker facing the
rear of the vehicle, align the mounting slots
on the Internal Cargo Tray (Item 1) with the
M6x12 Button Head Bolts and slide the tray
into position as seen in Fig 2.3.
Tighten the M6x12 Button Head Bolts.
3
2
4
56 2
A
B

VACC120_REV _A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS 4
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!