Front Runner FAFE001 User manual

ENG
180 min
Ford everest (2015 - current)
Foot Rail
FAFE001_REV_A00_MV © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
1
IMPORTANT WARNING!
Don’t be a hero and muscle through this without first reading these fitting instructions! Improper installation of this gear may void certain aspects of
your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
FAFE001
READ ME FIRST
START HERE!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

FAFE001_REV_A00_MV © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS 2
IN THE BOX
FIGURE 1.1
1 2 X Rear Foot Rail; 1xLH, 1xRH
2 2 X Front Foot Rail; 1xLH, 1xRH
3 8 X M6x16 Button Head
4 8 X M6x12x1 Stainless Steel Flat Washer
5 8 X M6 Nyloc Hex Nut
6 16 X M6 Nut Cap
7 12 X M8x20 Hex Bolt
8 12 X M8x16x1.6 Flat Washer
9 12 X M8 Nyloc Hex Nut
10 12 X M8 Nut Cap
11 8 X M6x30 Hex Bolt
12 8 X M6 Spring Washer
13 8 X M6x19x1 Stainless Steel Flat Washer
IN THE BOX
TOOLS NEEDED
13mm
10mm 4mm
Allen Key
Measuring
Tape
IN THE BOX IN THE BOX
14 2 X Splice Plate
15 8 X Foot Spacer
16 8 X M6 Channel Nut
17 1 X Protective Rubber Strip 250mm Long
IN THE BOX IN THE BOX CONTINUED
3
12
11
6
13
6
4
14
5
10
8
9
15
16
2LH
1LH
1RH
2RH
7
1GET ORGANIZED
Here is what you are looking at for FAFE001
Sealant

© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
3 FAFE001_REV_A00_MV
2.1
2.2
2.4
Prepare the channel nuts (item 16) by
stretching out the spring to use it as a
handle.
Place a bead of sealant in and over each
hole in the roof, then place a spacer over
each hole (item 15).
Cut a 20mm piece of item 17. Remove
backing and place under item 15.
2.4
Join the two halves of the foot rails with
the supplied splice plate (Item 14).
Fasten as shown with items 5, 4 and 3.
Now place the assembled foot rail onto
the spacers and fasten with items 11, 12,
13 and 16.
6414
5
15
16
6
11
12
13
3
To achieve this installation you will need to remove the Interior roof lining and then the factory roof rails.
FIT AND SECURE
2
10mm
Tighten all the nuts and bolts securing the foot rails to the vehicle's roof. Place a M6 Nut Cap (Item 6)
over each of the M6 Nuts and Hex Bolts.
2.5
10mm
16
4mm
10mm

© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
4 FAFE001_REV_A00_MV
Congratulations. You did it. Take a step back and admire your work!
FIT AND SECURE
3
3.3
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
Now's the time to visit your favorite Front Runner Dealer in person or Online.
Fit your roof rack to the foot rails with
items 7, 8 and 9.
Make sure that the wind deflector is
installed before you proceed to the next
step.
COMPLETION
4.1
4
3.2
13mm
3.1
Refer to RRSTUNI when assembling your Slimline II Tray.
3.4
Centre the rack and tighten fully. Use the supplied M8 nut caps (Items 10) to finish off the nuts.