Front Runner TRFD001 User manual

ENG
TRFD001_REV_A00 © 2019 FRONT RUNNER VEHICLE OUTFITTERS
1
Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
TRFD001
READ ME FIRST
START HERE!
front runner FORD /MAZDA DC TRACKS /1250MM
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

TRFD001_REV_A00 © 2019 FRONT RUNNER VEHICLE OUTFITTERS 2
FIGURE 1.1
IN THE BOX
1 2 X Track - 1250mm Long
2 2 X Rubber Strip - 1250mm Long
3 10 X M6 x 25 Countersink Bolt
4 10 X M6 Rivnut
1GET ORGANIZED
3
TOOLS NEEDED
9mm
5mm
4mm
1
2
4

© 2019 FRONT RUNNER VEHICLE OUTFITTERS
3 TRFD001_REV_A00
FIT AND SECURE
2
2.1
2.2
2.3
Place the track (Item 1) on roof so that rear
is level with rear door. Track must run next to
the rib in roof. Mark all five holes in the track
onto the vehicle.
Remove the Track and drill a 5mm pilot hole
on all the marks you have made. Open the
holes to 9mm.
Insert and set M6 Rivnut (Item 4) in all the
holes drilled in 2.2.
Treat holes with Anti rust and place Silicone
in and around all the M6 Rivnuts (Item 4).
Before starting the fitment, remove the
protective strip from the double sided
tape applied to the bottom of the Tracks
(Item 1) and fit the Rubber Strip (Item 2)
to the bottom of the Tracks.
5mm
9mm

COMPLETION
3
3.1
Congratulations! You did it. Take a step back and admire your work!
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
IMPORTANT!
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER
FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.
© 2019 FRONT RUNNER VEHICLE OUTFITTERS
4 TRFD001_REV_A00
FIT AND SECURE
2
2.4
Place the Track in position again and secure
using M6 x 25 Countersink Bolts (Item 3).
4mm