Frontier CT5401B User manual

NOTE: If any parts are missing or damaged, or if you have any questions, please send an email
to or call 678-585-4431.[email protected]
54”1 DRAWER WORKBENCH
CAUTION:
Read and follow all Safety Rules and Operating instructions before first use of this product
Notice: Picture shown is for illustration purpose only and may differ from the actual product.
678-585-4431
XDDPRODUCTS.COM
CT5401B

wearandtear.
thereplacementorrepairofsaidproduct.
The manufacturer warrants the product to be free from defects in materials and workmanship
for a period of one (1) year from date of purchase. This warranty applies only to the original
consumer and only to products used in normal use and service. If this product is found to be
defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that the product has
not been damaged through misuse, abuse, accident, modifications, alteration neglect or
mishandling. This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result
of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure
not relating to faulty material or workmanship. This warranty shall not apply to the finish on
any portion of the products such as surface and/or weathering, as this is considered normal
The manufacturer does not warrant and specifically disclaims any warranty, whether express
or implied, of fitness for a particular purpose, other than the warranty contained herein. The
manufacturer specifically disclaims any liability and shall not be liable for any consequential
or incidental loss or damage, including but not limited to any labor/expense costs involved in
Contact the Customer Service Team at 678-585-4431 or CustomerService XDDPRODUCTS.COM
WARRANTY
NOTE: If any parts are missing or damaged, or if you have any questions, please send an email
to or call 678-585-4431.[email protected]

NOTE: If any parts are missing or damaged, or if you have any questions, please send an email
to or call 678-585-4431.[email protected]
AA
BB
NO
76
8
10
8
26
M6x10mm screw
QTY
M6x16mm screw
CC
DD
EE M6Nut
FF
GG
M4x50mm Selftappingscrew
M4x10mm screw
M5x15mm Self tapping screw
6x25x1.0mmWasher
4
4
KEY PARTS DIAGRAM
A
B
C
D
E
NO ITEM
4
1
2
2
2
AB
C
DF
E
G
H
I
J
leg
Galvanized worktop
Front and back rail
Shelf
Inner plate(D1) with ball bearing slide(D2)
QTY
F
G
H
I
J
Pegboard supporter
Connect bracket
Drawer
Pegboard
Top tray
2
1
1
1
1
ITEM

NOTE: If any parts are missing or damaged, or if you have any questions, please send an email
to or call 678-585-4431.[email protected]
ASSEMBLY
Remove the protective film, using18pcsM6x16mm screws (AA) to install the bottom shelf (B) with
three legs (A).
Step1
1 2
Remove the protective film, install the second shelf (B) and fix the fourth leg (A) using 30pcs
M6 x 16mm screws (AA).
Step2
Number
Name
Quantity
AA
AB
18
1
Shelf
3
Leg
AA
A
B
M6 x 16mm screw
BAA
Number
Name
Quantity
AAA
30
1
1 2
B
AA
A
AA
M6 x 16mm screw
B
1
Shelf
Leg
ATTENTION:Do not tighten the screw until the installation is complete.

Place worktop on the ground with the wooden side facing up. Attach front and back rails (E) with
16 pcs M5 x 15mm Self tapping screws (DD) to the wooden side of the work surface. Once attached,
reorient assembled bench with the feet on the ground and then remove protective film.
NOTE: If any parts are missing or damaged, or if you have any questions, please send an email
to or call 678-585-4431.[email protected]
ASSEMBLY
Step3
Step4
Install the front and back rail (E) with 16pcs M6x16mm screws (AA).
Note: The holes on the rails should face upwards. These rails are used to assemble the galvanized
work top.
Correct
Wrong
Number
Name
Quantity
EAA
162
Front and back rail M6 x 16mm screw
AA
EE
E
Number
Name
Quantity
CDD
161
Galvanized work top M5 x 15mm Self tapping screw
A
CDD
Attention
Close to the edge
x
Keep (x) at a proper distance

NOTE: If any parts are missing or damaged, or if you have any questions, please send an email
to or call 678-585-4431.[email protected]
Back Front
Number
Name
Quantity
D1 CC
82
Inner plate
D2
2
Ball bearing slide M4 x 10mm screw
1
CC
D1
D2
ASSEMBLY
Install the ball bearing slide (D2) on the inner plate (D1), then install the inner plate with ball bearing 
slide (D) on all legs, using 8 pcs M4 x 10mm (CC) screws.
Step5
Install the (G) on the with 8pcs M5 x 15mm S pegboard supporter Galvanized work top elf tapping
. screws (DD)
Step6
Number
Name
Quantity
GDD
82
Pegboard supporter M5 x 15mm S screwelf tapping
DD
G
&
G
C
G
C
2
Upward
D
CC
Attention
Attention

NOTE: If any parts are missing or damaged, or if you have any questions, please send an email
to or call 678-585-4431.[email protected]
ASSEMBLY
Install the Pegboard (H) on the (G) and pegboard supporter galvanized work top(C) , using 6pcs
M6x16mmscrews (AA) and 2pcs M5 x 15mm elftappingscrews (DD) respectively. S
Step7
Number
Name
Quantity
HAA
61
Pegboard
1 2
DD
2
Install the (I) on the side bracket with 4pcs M6 x 16mm screws (AA). Connect bracket
Step8
Downward
Upward
Number
Name
Quantity
I
1
Connect bracket
AA
4
M6 x 16mm screw M5 x 15mm Self tapping screw
M6 x 16mm screw
G
AA
H
DD
H
C
I
AA
GI
Attention

NOTE: If any parts are missing or damaged, or if you have any questions, please send an email
to or call 678-585-4431.[email protected]
ASSEMBLY
Install the t t (J) on the pegboard supporter (G) and Pegboard (H), using 8pcs M6x10mm op ray
screws (BB), 2pcs M6 x 16mm screws (AA) and 10pcs M6 nuts (EE) respectively.
Step9
Number
Name
Quantity
J
1
Top tray
EE
10
M6 Nut
J
BB
G
EE
J
H
Step10
CAUTION: Finally tighten all the screws.
Align the guide rail and install the drawer (F), then fix the table on the wall, using 4pcs
M4 x 50mm self tapping screw screws (FF) and6x25x1.0mm washers (GG).
F
Number
Name
Quantity
F
1
Drawer
FF
4
M4 x 50mm Self tapping screw
GG
4
6x25x1.0mm Washer
FF GG
BB
8
M6 x 10mm screw
AA
2
M6 x 16mm screw

678-585-4431
Retain this manual for future use
XDDPRODUCTS.COM