Frontier WB602201 User manual

WB602201
SAVE THIS MANUAL FOR FUTURE REFERENCE
USE PRECAUTION
For your safety
INSTRUCTION
MANUAL
Read and understand
EYE PROTECTION
Must be worn
PROTECTIVE GLOVES
Must be worn when
handling tool
CAUTION: Read and follow all Safety Rules and Operating instructions before first use of this product.
NOTE: Ensure all components are present. If any components are missing, do not proceed with
assembly.Please send an email to [email protected]
5 FEET WORKBENCH WITH
CASTORS AND SINGLE DRAWER
60 in
22 in
40 in
Distributed by:
XDD products (USA), LLC
TGH (Cambodia) Industrial CO., Ltd
5011371

2
COMPONENTS
TOOLS REQUIRED
(NOT INCLUDED)：
5mm
Hex Key
PH2
Screwdriver
4mm
Hex Key
B
C
A
I
AA
DD
F
D
H
E
G
BB
CC
Hook
C
PART PIC DESCRIPTION QTY
AA
BB
CC
DD
1
2
1
1
1
2
4
1
30
16
16
1
1
A Leg
Beam
Leg with power charge strip
Rubber wood top
Drawer
Table stiffener
Drawer rail
Swivel casters with brake
Power strip
D
E
F
G
H
I
B
M4X10 cross flange bolt 4.8 grade black
M6X20 Inner hexagonal at head bolt
M8X20 Inner hexagonal at head bolt
M5X15 Cross head tapping screw
Please send an email to [email protected]
Ensure all components are present. If any components are missing, do not proceed with assembly.

3
ASSEMBLY
Attach the leg (A)(B) with beam (C) use 8
pcs M8 x 20 (BB).

Place table top (D) facing down on a flat surface with corner labels facing upward. Use soft moving
blanket or packaging material to protect top during assembly.
Align the positioning label and install the legs (A&B) & beams (C) on the rubber wood top using M5 x
15 cross head tapping screw(AA).


Positioning Label
Step1
PART
DESCRIPTION
BBCBA
QTY
Leg with power
charge strip Beam M8x20 Inner hexagonal at head bolt
Leg
8211
Step2
PART
DESCRIPTION
B CA AA
QTY
BeamLeg M5x15 cross
head tapping screw
Leg with power
charge strip
1 21
D
Rubber wood top
1 24
BB
C
C
B
BB
A
BB
A
C
D
C
AA
B
C
A
D
C
AA
A
B
D
AA
NOTE: Do not tighten all the screws before the final step.

4
ASSEMBLY
Attach the table stiffener (F) with rubber

wood top (D) use 6 pcs M5 x 15 (AA).
Attach the drawer rail (G) with leg (A)(B)
use 8 pcs M8 x 20 (BB).

Step3
PART
DESCRIPTION
D
QTY 1
Step4
AA
F
D
D
AA
F
BB
G
G
A
B
G
A
BB
AA
6
M5X15 Cross
head tapping screw
Rubber wood top
F
1
Table stiffener
M8X20 Inner
hexagonal at head bolt
PART
DESCRIPTION
B GA
QTY
Drawer rail
Leg Leg with power
charge strip
1 2 81
BB

5
ASSEMBLY
Attach the swivel casters with brake (H)
with leg (A)(B) use 16 pcs M6 x 20 (CC).

Inserting the drawer: Pull the slides and slide carrier out until fully extended.Hold the slide on the drawer
while aligning it with the slide on the plate.Slightly insert one side and repeat for the other side.Slowly
push the drawer until it is fully closed to engage slide.


Step5
PART
DESCRIPTION
CCHBA
QTY
Leg with power
charge strip
M6x20 Inner
hexagonal at head bolt
Leg
16411
Step6
PART
DESCRIPTION
E
QTY
Drawer
1
CC
B
H
A
CC
A
H
Swivel casters
with brake
E
E
LEFT RIGHT
Removing the drawer: Fully empty and extend the drawer. Push up the release lever on the left drawer
slide while pulling down the other release lever. Pull the drawer outward until it is released from the slides.

6
ASSEMBLY
Please recycle where facilities exist. Check with your local authority for recycling advice.

DISPOSAL INFORMATION

CUSTOMER SERVICE
Step7
Attach the power strip (I) with leg (B)
use 1 pcs M4 x 10 (DD).

PART
DESCRIPTION
DDI
QTY
Power strip
11
M4X10 cross flange
bolt 4.8 grade black
I
DD
I
DD
If you are having difficultly using this product and require support, please send an email to customerservice
@xddproducts.com